RF Sensors
Detect RF signal and represent the detected signal level in a manner that can be measured and recorded.
See Also: RF Power Sensors
-
Product
High Current Sensor
HCS-BTA
-
Vernier Software & Technology, LLC
Use the High Current Sensor in experiments that involve currents larger than 1 A, such as solar panels, hand generators, and other alternative energy projects.
-
Product
Ultra-compact Photoelectric Sensor
EX-20 Ver.2
-
Panasonic Industrial Devices Sales Company of America
Using a single chip optical IC, Panasonic created the powerful EX-20 Ultra-Compact Photoelectric Sensors, which are among the smallest Photoelectric Sensors worldwide and in spite of their miniature size, the Sensors incorporate a sensitivity adjuster. Since a red LED dot light source is used, alignment and confirmation of the sensing position is easy, even if very tiny objects have to be detected.
-
Product
PAMAS Sensors
-
PaMas Partikelmess- und analysesysteme gmbH
High-precision, German-engineered laser-based instruments designed to measure solid particle contamination in liquids.
-
Product
RF Multi-Coupler
MC108-2
-
Systems Engineering & Management Company
The MC100 Series Multi-Coupler is a 1U Rack-Mount device that provides RF distribution form 200 MHz to 5250 MHz. Both single and dual output configurations are available, as well as up to 8 output channels. Each output is an independent channel with +/- 5 dB gain controls, providing the ability to balance all outputs within +/- 1 dBm. Frequency Channel selection is from both front panel controls as well as remote control via Ethernet and SEMCO's MCCS Network software program.
-
Product
RF Reference Source
96040A Series
-
The 96040A RF Reference Source enables you to simplify your RF calibration system by replacing many of the instruments and accessories that make up your current system.
-
Product
Infrasound Sensors
MB3a
-
The MB3a is an infrasound sensor developed by the CEA, following the MB2000 and MB2005 series, which allows the recording of very-low-frequency acoustic signals over a broad frequency band, with an excellent resolution and a large dynamic range.
-
-
Product
High Performance LXI RF & Microwave Multiplexers
Microwave Multiplexer
Our standard microwave multiplexers offer the highest density configurations available, packaging up to 16 SPnT switches into a 2U high rack-mount enclosure. Standard microwave multiplexer systems include 50Ω Versions up to 67 GHz and 75ΩVersions up to 2.5 GHz. Alternatively, you can use our Microwave Switch Design Tool to mount any combination of our wide range of transfer and SPnT relays onto your own front panel design.
-
Product
Linear Position Sensors and Transducers
-
Linear Position Sensors and Transducers are used throughout many industries including; test/lab applications, medical applications, Motorsport, industrial processing, industrial machinery and mobile vehicleapplications. You may have come into contact with these types of sensors in everyday life. Some of the applications that they are used for include:
-
Product
Broadband Sensors
-
Offers a response between 120 sec and 160 Hz in a smaller, rugged, low power and low cost system that is easy to install and deploy. Built with ease of installation in mind, it does not require mass lock, mass centering, and has a large operational tilt range which combines to reduce installation training, time, and cost.
-
Product
Dielectric/Conductivity Sensor
Micro-VariconTM
-
The Micro-Varicon sensor is a miniature, thin, flexible dielectric sensor designedfor cost-sensitive use where space is limited. The electrode array is patterned on apolyimide substrate, and the Micro-Varicon sensor can be supplied with or withoutTeflon insulated leads.
-
Product
Torque Analyzers & Sensors
-
If torque tools slip out of calibration, that could impact the quality of your products. Having an accurate way to regularly test calibration onsite is a great way to reduce risk and ensure safety. With Mountz torque analyzers and sensors, you can test tools before they go into service every day. This prevents employees from working with miscalibrated tools and enhances quality management. It’s also more efficient to use your own torque testing equipment since you can evaluate your tools without sending them to a laboratory. Whether you want stand-alone sensors for hand and power torque tools or run down adapters that simulate actual joint conditions, Mountz has many options to choose from.
-
Product
Digital Displacement Inductive Sensor
EX-V Series
-
High-speed, high-accuracy, digital inductive displacement sensors with sub-micron resolution and an ultra-fast 40,000 samples/sec. sampling rate. Automatic Bottom-dead-center measurement mode. High-speed sampling : 40,000 samples/second. Digital Inductive Displacement Sensor
-
Product
Web Sensor
P8552
-
The devices are equipped with two connectors for connection of the temperature and humidity external probes and three binary inputs for two-states signals. The dry contact or two-state voltage signal can be connect to the binary input.
-
Product
Oxygen Sensor
KS60051
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Sensor Amplifier
UVM-SB
-
This is the relay amplifier box for the multi-point type UV monitors. Received UV light intensity is converted to electric signal for transmission. This allows distance between the light receiving inlet and the controller to 10 meters maximum.
-
Product
CW Power Sensors
E-Series
-
Operates with the EPM, EPM-P and P-series power meters Wide dynamic range sensors (-70 to +20 dBm)Accurate CW average power measurements Wide frequency coverage from 10 MHz to 26.5 GHz (sensor dependent)Calibration factors stored in EEPROM
-
Product
On / Off Tilt Sensor
SQ-SEN-390
-
The SQ-SEN-390 series sensor acts like a position sensitive switch which is normally closed when below horizontal and normally open when above horizontal.
-
-
Product
RF Switch Cards
-
The Adapt-a-Switch® RF switch cards deliver high performance and high density for your RF switching applications.
-
Product
RF Cables
-
RF/microwave interconnect and precision test cables for 50-Ohm and 75-Ohm systems from DC to 67 GHz with a wide selection of connectors including SMA, N-Type, F-Type, BNC, and 2.92mm!
-
Product
Peak/Average Reading Directional RF Wattmeter
83000-A
-
When you need Peak power measuring capability in the 2 to 2300 MHz frequency range and from 100 mW to 10 kW, then you need to get your hands on our Model 83000-A RF Peak Reading Wattmeter -- only from Coaxial Dynamics.
-
Product
Photoelectric Sensors
-
From long sensing range to oil resistance, Omron’s photoelectric sensing portfolio covers all the features required for advanced applications.
-
Product
4-20mA Sensor Converter
ENVIROMUX-S420MA-24V
-
External RJ45 device monitors up to two 4-20 mA analog sensors. Supports ISA Type 2, ISA Type 3, and ISA Type 4 sensors. Provides 24VDC, 25mA for each sensor. Connector: Screw Terminal, 8-position. Supports CAT5/5e/6 cable up to 500 ft. (152 m). Includes Mounting Hardware. Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: RoHS.
-
Product
Flat Carbon Sensor Conductivity meter
HE-960LF / FS-09F-1/2
-
It is effective to keep the dilution of Slurry constant. Maintaining an appropriate conductivity value contributes to process stability in the wafer polishing process. Even highly viscous sample liquids such as CMP Slurry can be measured without problems because they use a sensor structure that reduces the risk of the sample liquid sticking to the electrodes. In addition, the sensor is made of a wetted material with excellent chemical resistance, which meets the cleanliness requirements of semiconductor processes. In addition to the above, it can also be used for introduction at the semiconductor process development stage and conductivity control of special chemicals.
-
Product
chromatic Confocal Sensor Heads
ENDO
-
Sciences et Techniques Industrielles de la Lumière
STIL introduces ENDO series, a new range of chromatic confocal sensor heads with an exceptionally small size.With a mechanical diameter from 4 to 8 millimeters and a straight or radial beam of 90°, ENDO series is ideal for non-contact measurement applications in reduced space environments.
-
Product
DSP Sensors
-
Now available with an optional blue laser, LaserGauge® DSP Sensors are totally self-contained and allow single stripe, Cross-Hatch or Cross-Vector scans with unmatched speed and flexibility. DSP Sensors are capable of scanning a wide variety of surface types including solid metal, paint, plastic/rubber, headlamps, tail lamps, window glass, composite, chrome surfaces.
-
-
Product
Rate & Inertia Sensors
-
TE Connectivity (TE) provides electronic test and measurement systems, such as inertial sensors, rate sensors, and rate gyroscopes for demanding industrial, military, aerospace, automotive crash testing, robotics, biomechanics, and more.
-
Product
2D CMOS Image Sensor
Lince6M5
-
Lince6M5 is a single chip, fully digital, high speed CMOS active pixel sensor which is designed for maximum flexibility. It has excellent performance in a large variety of applications, ranging from low noise, high dynamic range surveillance, to high speed slow motion analysis, including high resolution machine vision applications. Lince6M5 incorporates a high speed 6.5MP CMOS active pixel image sensor providing both global and rolling electronic shutter, as well as High Dynamic Range (HDR) features. The sensor array utilizes active CMOS pixels with pinned photodiodes to deliver high image quality whilst maintaining the size, cost, and integration advantage of the CMOS technology.
