Speed
See Also: Sport, Dynamometers, Motor
-
Product
Bus Bar Protection
BUS1000/2000
-
The BUS 1000/2000 is a solid state, high speed protectionsystem for the detection of phase-to-phase andphase-to-ground faults on bus bar installations. It can beused to protect high voltage bus bar installations of anyvoltage.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
-
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Remote Spectrum Analyzers
LPT-3000RX4
-
Latest DSP Technology; 9 kHz to 3 GHz Frequency Range; External 10 MHz Reference; 17 RBW filters Down to 1 Hz; 17 VBW filters Down to 1 Hz; > 88 dBm Dynamic Range; High Definition Spectrum Trace; 55 dBm Input Port Isolation; 50 dBm input attenuator; 0.5 millisecond Port Switch Speed; Available in 4, 8 or 16 RF inputs; Optional Internal Carrier Identification CID module; Optional Internal Down Converter modules
-
Product
IO Expander
AD16x2DA16x8-125ETH
-
The IO Expander is an additional module to provide more input and output capabilities to the AD16x2DA16x8-125ETH. Via high speed link it connects 8 TTL inputs, 16 TTL outputs, 8 SPDT RF switches, and a GPS module.
-
Product
Airborne Network Flight Test Recorder
TTC nREC-7000
-
Curtiss-Wright Defense Solutions
The nREC-7000 is a high speed network recorder for use with Flight Test Data Acquisition and Multiplexing units. The nREC-7000 accepts data for recording on two 10GBASE-SR ports and two 1000BASE-T ports that can store data at sustained speeds of up to 1,000 MBps per 10GbE port. The recorder is also capable of acquiring, formatting (using PCAP, DARv3 or IRIG-106 Chapter 10/11), and recording 10GBASE-SR Ethernet at line rate.
-
Product
Air Core Line & Load Reactors
-
Line and load reactors are generally serial-connected to the input and/or output terminals of three phase equipment such as motor speed controllers, inverters and UPS systems. These equipment make use of semiconductor switches such as IGBTs, thyristors, and diodes and therefore create harmonic distortion and high switching over-voltages (dv/dt). Use of such equipment has been becoming more widespread as the technology advances. However, the negative effects of these equipment should not be overlooked.
-
Product
Vector Signal Analyzers
-
Vector signal analyzers combine superheterodyne technology with high speed ADCs and other DSP technologies to provide fast FFT-based, high-resolution in-channel spectrum measurements, demodulation, and advanced time-domain analysis. A vector signal analyzer is especially useful for characterizing complex burst, transient, or modulated signals in aerospace & defense, radar, wireless communications, and avionics.
-
Product
Dual Channel Analog Oscilloscope
MOS-620
-
MOS-6XXC Series dual trace oscilloscope, the maximum sensitivity is 5mV/div, the maximum scanning speed is 0.2us/div, and can be expanded 10 times to make the scanning speed reach 20ns/div. The oscilloscope adopts a rectangular CRT with a scale of 6 inches, which is easy to operate, stable and reliable.
-
Product
Gateway
CODA-4780
-
Hitron Americas Technologies Inc.
The CODA-4780 has the capability to receive 5Gbps based on 2 x OFDM + 32 QAM over its DOCSIS 3.1 interface. The integrated Wi-Fi 3×3 2.4 GHz 802.11n and 4×4 5 GHz 802.11ac Wave 2 dual band MU-MIMO Access Point significantly improves customer experience extending range and coverage with blazing speeds. For wired clients, the four Gigabit Ethernet ports offer ultra-fast connections. Its switchable upstream (5~85/5~204MHz) offers the possibility of flexible integration to existing networks.
-
Product
RF Mixers with Integrated LO
-
Analog Devices RF mixers/multipliers include both active and passive, as well as broadband and narrowband, products. These devices promise high performance and flexibility to help designers achieve their target specifications, reduce design time, and optimize costs. With leading specifications including speed, dynamic range, noise figure under blocking, SFDR, and ESD performance, ADI RF mixers and multipliers help to raise the bar within RF systems.
-
Product
Evaluation boards
-
iSYSTEM evaluation and development systems are optimized for evaluation of the featuring microcontroller whether it fits the project requirements or for the development of the target application while the hardware is still in the design stage. Our systems are distinguished by high speed debug and trace connection to experience the full microcontroller capabilities.
-
Product
Rectangular Connectors
-
Smiths Interconnect offer a broad range of modular and rectangular connectors. Our modular solutions allow the user to customize, configure and combine signal, Power, Filter High Speed Data (coax, twinax, triax, quadrax, fiber optic) contacts into a single connector.
-
Product
High Accuracy Fiber Optic Sensors
FS01
-
Compact & simple operation. New 12-bit concurrent CPU. 20-s response speed. Multiple calibration methods. Wire-Saving 0-line or 1-line connection
-
Product
LAN Cable Tester Plus
PK-3456 Spy Splitpair
-
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
-
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
VIEW
-
Quality Vision International Inc.
VIEW provides high speed, high precision non-contact measuring systems for manufacturing process control. VIEW’s high performance measuring systems and software are ideally suited for the small feature sizes and complex dimensioning schemes typical of micro-electronic and micro-fabricated parts.
-
Product
Telecommunications
-
TELETEL combines its communication and information systems expertise with its strengths in analogue and digital circuit design to develop products suitable for telecommunication, military and industrial applications. TELETEL's products exist in more than 20 countries in Europe, America and Asia. Every module on TELETEL's product line is designed, developed and tested to meet the increasing demands of today's technology for higher transmission speeds and enhanced system performance.
-
Product
4 1/2 Digital Multimeter
TH1941
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital multimeter TH1941 4 1/2-digit is voltage/current/resistance tester with multi functions and low cost. The instrument can stably perform measurement at high speed as several times as other instruments at the same level. It provides excellent performance, such as maximum reading of 21,000 counts, maximum DC voltage accuracy of 0.02%, and low cost to give you a best choice.
-
Product
Computer-On-Module
SMARC
-
SMARC form factor is the only computer-on-module form factor that truly is capable of supporting both ARM and x86 designs. With 314-pins on a high speed MXM3 connector, SMARC can fully cover both typical x86 interfaces as well as typical ARM type low level signals. Using ARM SoCs opens the possibility to leverage the product ecosystem of familiar devices such as tablet computers and smart phones. Alternative low power SoCs and CPUs, such as tablet oriented x86 devices and other RISC CPUs may be used as well.
-
Product
BF-Series Soft Stop Models
-
The E-DRIV® BF-Series soft stop models is designed with an unique "soft-stop" shock absorbing clutch that is ideal for fastening shock delicate components such as disk drives, plastics, and electronics. The ergonomically designed soft stop clutch reduces impact and vibration transmitted in the screw fastening process, which delivers less torque reaction to operator. The electric screwdriver offers an adjustable speed setting and a selectable Soft Start mode. Designed for precision torque control the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
PMC Compatible SpaceWire Interface
PMC-SpaceWire
-
Utilize SpaceWire to communicate with the European Space Agency and NASA equipment utilizing the ECSS-E-50-12A specification. SpaceWire is configured using routers to create a heirarchical point-to-point system with high speed parallel paths. PMC SpaceWire implements SpaceWire in a convenient PMC format. With PMC you can install the adapter into PCI [PCIBPMC], cPCI [cPCI2PMC], or processor board pmc slots. The SpaceWire specification calls for LVDS signaling and a specific 9 pin micro-D connector. You can connect the PMC-SpaceWire to other SpaceWire compliant devices without electrical interface issues.
-
Product
Surface Measurement Instrumentts
-
Analyze surfaces texture with nanometer precision is already a technological challenge, but TR Scan Premium is able to perform this task with unprecedented speed! The TR Scan Premium is used in workshops and laboratories worldwide. It is completely designed and manufactured in Switzerland by TRIMOS. The TR Scan is focusing on Digital Holographic Imaging Technology. Accuracy, speed, ease of use and modular construction make it ideal for all types of surface measurements.
-
Product
Copper TAPs
-
Profitap Copper TAPs provide complete access and visibility into your network by creating an exact copy of full-duplex 10M/100M/1G/10G traffic at wire speed with no impact to the network link. Profitap Copper TAPs introduce no point of failure to the network. They are designed for redundant powering, which allows a second power supply to activate if the first were to become unavailable. In case of complete power loss, Profitap Copper TAPs guarantee that the link remains operational by instantly switching to a fully passive mode.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 32 Channels
DN6.593-32
-
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Programmer AUTO300 Weilei Memory
-
AUTO300 is the newest programmer from weilei company. That programmer is dedicated to automotive electronics. The main advantages are : reliability, speed, and the ratio of quality to price, the software in ten languages and 3-year warranty
-
Product
UniPro/UFS Analyzer/Exerciser
Eclipse M52
-
Implementing a new high speed front end, supporting MIPI M-PHY™ HS-Gear5 at speeds up to 23Gbps, the Eclipse M52 stands as the markets most complete analyzer/exerciser. The Eclipse M52 is the right tool for engineers and developers who need to ensure the correct and efficient operation of technologies employing the high data transfer speeds of the UniPro/UFS specifications.
-
Product
Non-Signaling RF Test Platform for Validation & Production
Universal Wireless Tester
-
Wireless communication standards are increasingly integrated into vehicles as well as smart home and Internet-of-Things applications. They form the basis for connected services, advanced HMIs, and autonomous driving. The combination of constantly evolving standards and the integration of multiple wireless technologies with many RF channels into new product designs means that measurement speed and quality are becoming a priority.
-
Product
2D-3D Laser Measurement
-
Long range profiling laser displacement sensor is built to satisfy the most demanding automated dimension, angle, curvature and height in the industrial application. At a fast speed of 6,000 frames per second and up to 2.5µm resolution, it also has measuring of up to 800 mm.
-
Product
Towing Dynamometer
RS-10K
-
RS-10K Towing Dynamometer is designed for testing today’s mid-sized cars and SUVs. The RS-10K is built with an all aluminum frame, an aerodynamic body and rides on an independent, air ride suspension and uses an eddy current absorber with special high temperature coils to absorb energy. The RS-8K is powered by an industrial generator, so unlike battery/alternator Towing Dynamometers, there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
Product
Circuit Card Assembly
-
Teledyne Advanced Electronic Solutions assembles and tests a variety of complex circuit card assemblies (CCAs) using leading edge, advanced technology assembly automation. We specialize in low-volume, high-mix assembly of highly complex CCAs.- RF, analog, high-speed and digital circuits on rigid-flex and Cu core substrates- Typical lot sizes from 3 to 300 pieces- 4 high speed, flexible SMT lines- Production processes for components from 0201 chips to large grid-array components and connectors- 100% solder paste, automated optical, and x-ray inspection- Forced air convection reflow with inert atmosphere option- Special processes for RF assemblies (filters, shields, etc)- BGA underfill, conformal coating, etc.- Selective and wave solder pin-thru-hole processes- CCA and component bonding processes
