Vickers Hardness Testers
See Also: Hardness Testers, Brinell Hardness Testers, Leeb Hardness Testers, Rockwell Hardness Testers
-
Product
Primary Injection Testers
AT-10B
-
ETI’s AT-10B autotransformer steps-down 480V outputs to 240V outputs. This portable autotransformer allows ETI’s PI-1600 or PI-800 circuit breaker testers to be used at full-capacity on 240 and 480 VAC lines. The unit provides 240 VAC at 10 kVA, is housed in a rugged ABS enclosure approximately 22″ x 11″ x 22″, and weighs less than 125 lbs.
-
Product
AMIDA IGBT Tester
600
-
KVI Source: 1 Channel 4Q V/I Source; ±1000V, ±10mA Source ability; V/I read back at 16 bits resolutions under 100Ks sampling rate ; ±0.2% accurate reading of Range
-
Product
Electrical Installation Testers
-
Continuity tester for measuring the resistance of the protective earth conductors and earth bonds – an ohmmeter dedicated to electrical safety
-
Product
Freezing Tester
-
Our Freezing Tester units are available in vertical or horizontal configurations are used to test the bending/flexing durability of rubber, plastics, synthetic leather, shoes, etc., under cold temperatures as low as -30°C or -70°C depending on the selected model. The test chambers can be equipped with a variety of flexing/bending fixtures made of stainless steel. These models conform to ASTM D 1790, and ASTM D1593 standards.
-
Product
Chip Tester
-
Chip aging test is a very important task. It simulates various environmental and stress conditions of the chip during long-term use, evaluates its reliability and life, and provides effective reference and guidance for chip product design and manufacturing. It is necessary to select high-quality chip testers to ensure accurate test data, thereby further improving the reliability and life of chip products.
-
Product
AMIDA 3001XP Tester
-
AMIDA has introduced two new analog/mixed-signal and logic options in the AMIDA-3000 series in recent years—the AMIDA-3001XP and AMIDA-3KS test systems. Both reinforce the AMIDA-3000 series' ability to provide cost-optimized test solutions for a variety of consumer components in power management and mobile device components. The AMIDA-3000 series provides more than twice the number of analog channels of its modules per test system, thus greatly reducing the acquisition cost of each channel and more than doubling the number of analog channels in the entire test system. This results in a higher number of parallel tests and a higher level of capability for this system, as well as a lower and more cost-effective IC unit test cost for this tester. This series of test systems provides a powerful test combination with high-speed hardware and software integration. The built-in instant messaging protocol detection function of AMIDA-3001XP test machine not only simplifies the complexity and difficulty of test development, but also greatly shortens the test time by using its high-speed computing capability.
-
Product
Transformer Performance Tester
JYW6100
-
JYW6100 Transformer No-loads and On-loads tester power factor tester is suitable for loss testing of low power factory transformer such as amorphous alloy transformer, with high precision and data loc
-
Product
Adhesion Testers
-
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
Product
Single-functional testers
3123
-
The MI 3123 SMARTEC Earth / Clamp is an earth resistance tester with the ability to perform 4-wire earth resistance measurement and 4-wire specific earth resistance measurement. With the optional A 1018 and A 1019 current clamps the instrument can perform 4-wire earth resistance measurement with one current clamp, contactless earth resistance testing with two clamps and TRMS current measurement up to 20 A. Configurable limits enable a PASS / FAIL evaluation of test results.
-
Product
Electric Testers
-
ATEQ offers a broad range of electric testers designed to meet the diverse needs of various industries. These testers, including advanced battery testers, are pivotal in ensuring the efficiency and safety of electrical systems. They are used in applications ranging from automotive and e-mobility to broader industrial purposes and EV battery testing. ATEQ’s electric testers are known for their precision, featuring integrated databases for battery types and parameters, secure systems with comprehensive battery protections, and user-friendly interfaces. This makes them essential tools in production lines, research and development laboratories, and for EV/HEV expertise
-
Product
Current Tester
MIG0624
-
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
Product
Permeability Tester for Diapers
DRK357B-II
-
Shandong Drick Instruments Co., Ltd.
The diaper permeability tester is used to determine the absorption speed, re-permeability and permeability of diapers and other products.
-
Product
Current Transformer Testers
-
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
-
Product
Hipot Line Testers
-
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
Product
Respirator Fit Testers
-
Respirators and masks play a crucial role in protecting workers from various airborne hazards, including environmental and chemical dangers, as well as airborne biohazards, in the workplace.
-
Product
Torque Tester
DIS-IP Series (-IP05/5/50/200/500)
-
For managing various manual torque wrenches and torque drivers. Standard product for static torque measurement. Display characters are larger, improving usability. Installation in a small space is now possible with the separated type. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
Product
Single Sheet Tester
Model SST500X500
-
Gopal Make single sheet tester SST is developed as per IEC 60404-3. It can be attached as probe to Ep400 Main unit and user can test specific total loss, specific apparent power, and r.m.s value of magnetic field strength as well as B/h curve in the software.
-
Product
Relay Tester
-
Beijing GFUVE Electronics Co.,Ltd.
Assists in the inspection, installation, and repair of assigned electro-mechanical controls and equipment systems.
-
Product
Signalling Testers
-
Anritsu's strong and flexible Signalling Testers are a key part of Anritsu's total wireless test and measurement solution, utilizing technology developed through our global leadership in this market.
-
Product
Withstand Voltage Tester
2672AM
-
Shenzhen Chuangxin Instruments Co., Ltd.
Withstand Voltage Tester is used to measure the dielectric (withstand voltage) strength, which can be intuitive, accurate and fast tested the electrical safety performance indicators of the object, such as the breakdown voltage, leakage current etc. And Withstand Voltage Tester can be used as a high voltage source to test performance of the components and whole machine.
-
Product
Leakage Current Tester
-
Test Voltage : - 1V to 500V DC settableAccuracy : ± 1% of set Value ± 1digitLeakage Current : - Accuracy - ± 0.5% ± 1digitDigital Model – 19.99μA / 199.9 μA / 1.999mA / 19.99mAAnalog Model - 10μA /25μA/100 μA/1mA/2.5mA/10mASeparate Indication for Charge / Measure and Discharge modeAvailable in Digital Version Also
-
Product
Various Types of Automatic Hardness Testing System
-
Various Types of Automatic Hardness Testing System
-
Product
Martindale Abrasion Tester
GT-KC13A
-
To determine the abrasion resistance of all kinds of footwear vamp material. Samples are rubbed against known abrasion at low pressures and in continuously changing directions and the amount of abrasion. The unique design allows removal of individual sample holders for examination without lifting the top motion plate.
-
Product
Digital Phosphate Tester
MW12
-
The Milwaukee MW12 Phosphate Photometer lets you go digital with your testing. No more hit and miss testing with strips. Great for aquariums, aquaculture & coral, labs, water treatment, classroom and more. This meter is also ideal for educators that want their students to learn the basics of water quality analysis to apply in the real world.
-
Product
Rad Hard Power Sequencing
-
Renesas' radiation hardened quad power supply sequencers are designed to drive point-of load (POL) regulators that power high performance FPGAs and complex, multi-rail power systems.
-
Product
IPTV Tester
NetProbe 2000 IPTV Analyzer
-
The NetProbe 2000 IPTV is a handheld IPTV tester that can emulate a set top box or passively monitor video channels in pass-thru mode. It can be used to turn up new service by auto scanning all channels and checking their quality or to troubleshoot the service. It is battery powered and easy to operate by a tier one technician.
-
Product
Adhesive Tack Testers
-
Adhesion test is to measure the initial tack and holding power of adhesive tapes and labels. Tack or holding power test is very important in packaging industry and adhesive industry.
-
Product
AC Hipot Testers
VLF
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Programmable micro-controller• Advanced digital frequency technology• Built-in printer•Portable• AC HIPOT testing of cables and electrical apparatus is now easier than before•UDEY VLF testers are suitable for testing cables, transformers, switchgear, rotating machinery, & other electrical apparatus.
-
Product
Transformer Bench Tester
KVBT
-
KV Hipot Power Test Equipment Co.,Ltd
Transformer Test System is applied for ex-work and maintenance detecting on various transformers.
-
Product
Electronic Tire Tester
Model BTT-5700
-
The Branick BTT-5700 was created from the ground up to be the most efficient, durable and reliable electronic tire tester available. The electronic detector accurately locates flaws that may be missed using conventional methods. A visible spark occurs at the site of a flaw and the rotation stops to allow the flaw to be marked. The adjustable height platform reduces physical strain that can often lead to workers compensation claims. The BTT-5700 also features a bi-directional variable speed electric rotation motor that is whisper quiet. The auto extend/retract ramp makes tire loading easy. Hand controls are located on a locking swing arm that can be adjusted in seconds. Four air tool ports and two electric outlets are also provided so any needed tools can be kept close for improved efficiency. A high power LED light and Medium Truck Probe are also included. All probe heads require only the push of a button to change and are available to fit all common tire sizes. And, like everything from Branick, it's made in the USA.
