Control Systems
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 510 Ohm - SPST
50-294-114
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Flight Control System Test Platform
The Flight Control System Test Platform provides a hardware in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of Flight Control Systems (FCS) of both commercial and military aircraft. The system simulates control surface activities from multiple combinations of rudder, flaps, elevator, aileron, and engine controls to the FCS. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation test systems.
-
product
Vapor Source Mass Flow Controller With Viscous Choked Flow
The 1150C Vapor Source Mass Flow Controllers are pressure based measurement and control systems designed to meter and control vapor from low vapor pressure liquid and solid sources directly, without the need of a carrier gas using viscous flow through a choked orifice.
-
product
Electrical Creep and Rupture Testing Machine
ECR Series
Jinan Testing Equipment IE Corporation
This series of computer control electronic creep and rupture testing machine is newly designed with full-digital measuring control system to meet the standards of GB/T2039, GB//T20120, EN ISO 204-2009 and ASTM E139 etc. The electronic creep and rupture testing system can perform not simply creep. stress-rupture test and stress relaxation test on metals under room or high temperatures, but also low cycling test & creep fatigue test. The electronic creep and rupture testing machine is widely used for quality control in factories, material research in R&D department and teaching in universities,
-
product
IP Reuse
IC Manage Global Design Platform (GDP & GDP-XL) includes an open platform for maximizing IP reuse. Design and verification teams can use the system to rapidly publish and integrate IP into existing flows, and to trace bug dependencies. Internal and third party IP can be imported or linked with IP Central from multiple commercial and open source design management systems, as well as internal revision control systems. ”
-
product
Transducer Calibrator Systems
Unholtz-Dickie Calibration Systems have earned their place in industry as the standard for calibrating accelerometers and velocity transducers. The Models 660C & 680C are UD''s latest generation of automatic calibration systems, both utilizing the expanded features of the i5 based APEX SL Windows vibration control system.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm With SPDT
50-293-111
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
224 Channel Digital I/O Modular PXI Card
GX5731
The GX5731 is a 6U modular digital I/O card with 224 I/O channels. Designed for ATE, data acquisition, or process control systems where a large number of discrete I/O channels are required, the GX5731 offers the highest density in the industry for a single PXI plug-in board. Of the 224 channels, 128 support TTL levels with the direction of each group of eight channels programmable as input or output. The other 96 channels can be used for customized I/O using MTS' GX57xx series I/O modules.
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 1.5k
50-265-402
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 131k Ohm
40-294-034
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Dissolution Software for Enhanced Data Management
Agilent dissolution software systems enable more effective management and analysis of dissolution data, while ensuring ongoing regulatory compliance. Our dissolution testing data systems integrate analysis and sampling and provide real-time access to test status and simultaneous control of multiple systems.
-
product
PXI Resistor Module 2-Channel 2R to 65.5k
40-293-033
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
AXIe Switch Module
PK100x4
The PK100x4 AXIe module implements a 100x4 matrix switcher structure (100 inputs – 4 outputs). The module is designed to work in functional control systems, systems for monitoring and diagnostics of ground-based electronic equipment, control systems for bench tests.
-
product
Universal Military Craft Systems Controller
3U VPX
The system is 3U VPX based. It consists of two CPU modules, a power supply module [SMART.PSU] Technology explained <- Click here, two PMC/XMC carrier modules and two MILBUS modules. Optional: WLAN module for controlling the system externally without hanger access (Aircraft on runway - pre-takeoff)
-
product
PXI Strain Gauge Simulator Module 2-Channel, 2K
40-265-302
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Geophone Testing – Hydrophone Testing – Vibrator TestingVersatile Quality Control System - Three Test Units In One!
Bird Dog 3 - 3 Channels
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Three different operation with a single unit*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Three-Component Test Mode, checks 3 elements at onceto save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
product
Multicore Digital Signal Processor
SI-C667xDSP
Sheldon Instruments offers a complete portfolio of hardware products for a wide spectrum of real time applications in measurement and digital control systems. Our hardware range includes carrier boards that combine DSPs and FPGAs for various PCI/PCIExpress form factors such as slotted/desktop PCI/PCIe, PCI-104/PCIe-104, PMC/XMC, CompactPCI, as well as stand-alone embedded solutions. The DSP-FPGA carrier hardware is complemented by high performance analog and digital I/O modules as well as all necessary accessories like cables and terminal blocks.
-
product
PCI High Density Potentiometer Card 2-Channel, 16-Bit, 0 To 65k Ohm
50-296A-021-2/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Test Automation System for Brake Testing
STARS Brake
STARS Brake is an integrated automation, data acquisition and control system platform that provides a comprehensive application functionality in a single, powerful environment. STARS Brake is designed to address the needs of a wide range of brake testing applications from component development to final component and system validation. It offers users a level of flexibility and openness that enables thorough investigations of brake systems.
-
product
Wafer Level Multi-Die Test System
ITC55WLMD
The ITC55WLMD series of test systems has been developed by ITC to be stand-alone UIL test systems configured specifically to test on wafer. The systems include an ITC55series UIL tester and inductor box, a current limiter module and a system controller
-
product
The Language of Technical Computing
MATLAB
MATLAB is a high-level language and interactive environment for numerical computation, visualization, and programming. Using MATLAB, you can analyze data, develop algorithms, and create models and applications. The language, tools, and built-in math functions enable you to explore multiple approaches and reach a solution faster than with spreadsheets or traditional programming languages, such as C/C++ or Java. You can use MATLAB for a range of applications, including signal processing and communications, image and video processing, control systems, test and measurement, computational finance, and computational biology. More than a million engineers and scientists in industry and academia use MATLAB, the language of technical computing.
-
product
PCI High Density Resistor Card 5-Channel, 12-Bit, 0 To 4k Ohm
50-295A-021-5/12
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Instruments
Advanced Thermal Solutions, Inc.
ATS designs and fabricates the most extensive line of thermal test instruments specifically designed for the electronics industry. These research-quality, state-of-the-art instruments include Pressure, Temperature and Velocity Measurement Systems, Airflow and Heat Flux Controllers, Micron-level Thermography Systems and Cold-Plate Thermal Characterization Systems.
-
product
Motor Quality Control Test Systems
SKF Condition Monitoring Center
These rack-style motor quality control units are rugged, field-proven systems for testing stators and armatures in high-volume manufacturing environments. They combine the most common electrical tests into an efficient automated solution.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm
50-293-014
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Motors & Actuators
Our precision linear and rotary Voice Coil Actuators (VCAs) and Brushless DC Motors (BLDCs) produce, sense and control motion in high precision and high accuracy machinery. We also offer a series of VCA Developer's Kits that are easy to set-up and use without needing to specify a complete control system.
-
product
ABex Matrix Module with 86x4 or 43x8 Cross Points
ABex TM-404 Matrix
The ABex TM-404 is a 86×4 matrix designed as a universal connection between the test points and the measuring instrument. This can be done locally or via the ABex. The ABex TM-404 can be configured as a matrix with 4 or 8 busses. The internal matrix busses can be switched to the analog bus. The back connector allows to connect the TM-404 to the front of a Konrad PXI-501 ICT card to build a very compact ICT instrument. In addition, this combination can be used as an ABex system controller
-
product
PXIe-8842 2.6 GHz 6-Core Processor PXI Controller
790658-01
The PXIe8842 is an embedded controller for PXI systems that you can use for processor-intensive modular instrumentation and data acquisition applications. The PXIe8842 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, one Thunderbolt 4 port, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, and other peripheral I/O. Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
product
Serial Production Mark Quality Control
The control system is based on the Sick IVC smart camera, which not only captures, but also processes the image. After training on the font samples, the system practically does not require the operator's attention in addition to setting the current marking for control. The character set can be specified by the operator or transmitted via the interface from the printer or from the enterprise information system.The camera software works autonomously: it loads all settings from the camera's permanent memory, initializes the backlight electronics and waits for a signal from the object presence sensor. When a signal is received from the sensor (an object in the shooting area), the camera captures the frame, searches for markings and analyzes the symbols for their compliance with the exemplary set.
