Control Systems
-
product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 1.02k Ohm - SPST
40-294-121
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Checking the Geometry and the Placement of the Weld
Based on the real geometric three-dimensional profile of the weld (groove) on the outside of a large diameter pipe, determine the offset of the center of the weld (groove) from the weld line. Provide continuous output of results through the RS-232 interface to the welding process control system. Provide a graphical picture of the current profile, the values of the specified and calculated geometric parameters to the operator.
-
product
FPD Tester Model
27014
Chroma 27014 Flat Panel Display Tester is a complete testing solution that meets the Liquid Crystal Module testing requirements of production line. With integrated video generator, multi-channel precision power supply and process control unit, the system allows a complete test of signal, pattern and electrical parameters of LCM through a PC or remote control box.
-
product
Motor Drive Analyzer, 350 MHz, 8 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch
MDA 8038HD
Static power analysis - like a dedicated power analyzer.Dynamic power analysis – capture more information.Complete test coverage – control system, power section, motor.Comprehensive mechanical interface.Harmonics calculation option.Vector display option (THREEPHASEVECTOR).Waveform Transformations option (THREEPHASEdq0).16 Channels with OscilloSYNC™.
-
product
DynoLAB Test Cell Supervisory System
SAKOR Technologies’ DynoLAB™ data acquisition and control systems offer reliable, cost effective automation of all types of dynamometer test systems. As with all SAKOR products, the DynoLAB system undergoes a continuous program of upgrade and improvement, regularly expanding and enhancing DynoLAB’s capabilities.
-
product
3U CompactPCI Multi-Function I/O Board
CPCI-AD32
The CPCI-AD32 is a 3U CompactPCI multi-function I/O board. The CPCI-AD32 offers 32 channels of 16 bit A/D, two 16 bit D/A, 16 digital I/O, counter / timers.There is a local 60 Mhz TMS320C31 DSP processor to supervise all the I/O activity. The DSP can be programmed by the end user to execute application specific code. The CPCI-AD32 is ideally suited for factory automation, automatic test equipment, test & measurement, and control systems.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm - SPST
50-294-134
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Digital PFC Controllers with Power Metering
Are digital power factor correction (PFC) controllers that provide accurate input power metering capability and inrush current control for ac/dc systems.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm
40-294-033
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Vibration Test Chamber Elevator Mechanism System
Guangdong Test EQ Equipment co., Ltd.
- Structural Design: Monolithic construction with seamless TIG welding for durability and aesthetics. Lever-driven door lock mechanism.- Smart Control System: Features a Chinese/English-language color LCD touchscreen HMI + high-performance PLC, powered by TESTEQ's proprietary software for automated, intelligent, and user-friendly operation.- Energy Efficiency: Incorporates TESTEQ's patented "Static Balance" technology, reducing energy consumption by over 30% during low-temperature stabilization.- Vibration Integration: Elevator Mechanism: Wireless remote-controlled for alignment with horizontal/vertical vibration platforms.- Advanced Sealing: Custom flexible connectors ensure airtight integration between temperature/humidity chambers and vibration platforms.
-
product
PXI Resistor Module 2-Channel 1.5R to 4.09k with SPDT
40-293-123
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Test Automation System for Brake Testing
STARS Brake
STARS Brake is an integrated automation, data acquisition and control system platform that provides a comprehensive application functionality in a single, powerful environment. STARS Brake is designed to address the needs of a wide range of brake testing applications from component development to final component and system validation. It offers users a level of flexibility and openness that enables thorough investigations of brake systems.
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 350 Ohm
50-265-012
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Connector Blocks
VI Control Systems has designed several connector blocks for mating ribbon cables to screw terminals. Our design goal was to make the connector blocks small and inexpensive.
-
product
Differential Pressure Gauges
Differential pressure gauge is an economical means for measuring pressure between two independent pressure sources. Used on process monitoring or control, the unit's system design permits a small volume of media migration; intended for air, hydraulic oil and non-corrosive applications. A good choice for satisfying challenging pressure requirements.
-
product
Electrical Creep and Rupture Testing Machine
ECR Series
Jinan Testing Equipment IE Corporation
This series of computer control electronic creep and rupture testing machine is newly designed with full-digital measuring control system to meet the standards of GB/T2039, GB//T20120, EN ISO 204-2009 and ASTM E139 etc. The electronic creep and rupture testing system can perform not simply creep. stress-rupture test and stress relaxation test on metals under room or high temperatures, but also low cycling test & creep fatigue test. The electronic creep and rupture testing machine is widely used for quality control in factories, material research in R&D department and teaching in universities,
-
product
Control System
HICOS
HIGHVOLT Prüftechnik Dresden GmbH
The HiCOS controller is a collection of modules for monitoring test systems and recording, creating, evaluating and evaluating measurement data. It is suitable for mobile and stationary test systems as well as measuring devices. The modular design of the HiCOS controller allows the expansion of functions. Existing test systems from other manufacturers can be upgraded with HiCOS.
-
product
Software Development Projects
Precision Development Consulting Inc
Automation of new process tool prototype in startup environment, Complex R&D Gasbox Automation, Semiconductor System Control Software, Wafer Transfer Control Software, 300mm Factory Automation, Complete port of Spectrometer software to windows, HSMS Protocol
-
product
Wide FOV Target Projector
The Model 13792 is a broadband portable target projector used for characterizing the performance of a wide variety of infrared sensor systems. The system incorporates SBIR standard components to provide accurate and precise stimulus to sensors under test in laboratory, depot and production line environments. Testing can be automated with the use of IRWindows™ test system controller that reduces test times and cost, while improving the consistency and accuracy of test results.
-
product
Digital Positioners
Smart digital positioners form the vital link between the control system and the valve. Digital positioners from ABB incorporates auto-adjust to reduce commissioning time and an adaption program provides for optimal control of the position until set point is reached.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
High Output Simulators
The Abet Gen II optical design, patent pending, dramatically increases the percentage of photons reaching the work plane.All electronics are packaged in the lamp house – no clutter of high power cables to deal with. A digital shutter timer allowing both manual and external control is included with every unit.Standard maintenance, lamp or filter replacement, does not require any tools.Locking indicator dials on all the system controls provide for a reproducible and stable setup.
-
product
Industrial Control
Schweitzer Engineering Laboratories, Inc.
Industrial control systems require reliable automation solutions that can integrate with relays, meters, and plant controls to ensure the safe operation of industrial facility power systems.
-
product
FPGA Boards
For over two decades, Digilent has proudly worked with Xilinx to become a global leader in the design and manufacturing of cost-optimized field-programmable gate array (FPGA) and System on a Chip (SoC) development boards. Optimized for accessibility and flexibility, our control system boards are suited to a wide array of applications ranging from embedded vison and sensor fusion to networking and RF to embedded measurement and control systems. Enjoy high performance-to-price ratio, ease-of-use through onboard peripheral support, extensive documentation and example designs, and an open-source philosophy.
-
product
Low Power Comparators
Analog Devices low power comparators provide a capable solution to demanding applications that must operate in the µA range. To cover a range of design needs, our low power comparators are available in commercial, industrial, and automotive temperature ranges, with feature such as noninverting inputs and inverting inputs. This portfolio supports applications such as Li-Ion monitoring, handheld instruments, LED/relay driving, control systems, and optoisolator driving.
-
product
Incremental Encoder Simulator
ENC-SIM01
Plant Control and Automation Pty Ltd
This instrument is designed to simulate the function of most types of incremental encoders; it allows the engineer to fully test a control system that uses a rotary or linear shaft encoder, without the need for any mechanical movement.
-
product
LED Driver Aging Rack
LEDRACK-100W192P
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
product
Test Cell Controller
RAPID
The Rapid II Test Cell Controller is an integrated, multi-loop control and data acquisition system for test cell applications, designed to provide maximum performance at an affordable price. Rapid II combines the latest in digital control technology with off-the-shelf hardware to produce one of the industry's most powerful, flexible and advanced controllers at a cost-effective price. This high-speed, 4-channel PID controller includes ample I/O to act both as a system controller and a data acquisition system, reducing overall system cost and complexity. Designed for integrators, OEMs, and DIYers, these systems can be configured to fit your needs with little upfront costs and minimal risk while benefiting from a stable, powerful platform.
