Video Distribution Amplifiers
See Also: Distribution Amplifiers
-
Product
PHIL 4-Quadrant Power Amplifier
PAV5000
-
PAV5000 is the four-quadrant amplifier with high power applied in the semi-physical simulation power platform to analyzer the sensitive load, the equipment power adaptability, and the electric vehicle, etc. and provide the technical support and service on the power quality.
-
Product
Laser Scattering Particle Size Distribution Analyzer
Partica LA-960V2
-
This latest evolution in the LA series advances scientific knowledge for tomorrow's world through intuitive software, unique accessories, and high performance.The LA-960V2 continues HORIBA's proud tradition of leading the industry with innovative design.
-
Product
Linear Amplifiers
-
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-12GHz) linear amplifier for receiver-side applicationsFeatures controlled gain from 0dB to 31.5dBFeatures input offset adjustment and input peak detectorFully differential input interface with on-chip 50Ohm terminationFully differential output interface with on-chip 50Ohm terminationOutput 1dB compression point of 1.5dBm3rd Harmonic better than -47dBc within the full bandwidth15dB Noise FigureSingle +3.3V or -3.3V power supplyPower Consuption: 530mW typicalFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
Product
Broadcast Video Products
-
Macom Technology Solutions Holdings Inc.
Macom Broadcast Video Products
-
Product
Amplifiers, Splitters & Combiners
-
DEV’s RF Splitters, Distribution Amplifiers, or Dividers are used to distribute and amplify RF signals, to compensate for signal loss, and to provide redundancy paths to ensure maximum uptime.
-
Product
Goniophotometer For Luminaries Intensity Distribution Curve
LCG-1800
-
Shenzhen Chuangxin Instruments Co., Ltd.
Mainly used to measure FL etc. When installing luminaires, the lighting center of luminare and the rotating center of rotating table shall be at the same position. In B- coordinates, luminaire axis is superposed with the horizontal axis of rotating table. In A- coordinates, luminaire axis is vertical with the horizontal axis of rotating table.
-
Product
Gas Distribution Panels
PTS DII
-
PTS DII Gas Distribution Panels are similar to our PAO-DII Fluid Distribution Panels. They are designed to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger PTS, Portable Temperature Servo Conditioner or HPG, High Pressure Gas Conditioner. You can also use PTS-DII Gas Distribution panels with any other source of temperature controlled gas, including a competitor's air or gas source.
-
Product
Single Channel High Voltage Linear Amplifier
A600
-
The A600 is a general purpose broadband linear amplifier having a fixed amplification of 100 times and capable of bipolar high voltage output of 300V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to 3 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
High-Frequency Signal Amplifier
VCH-605
-
High-frequency signal amplifier VCH-605 is designed to amplify and multiply sinusoidal signals with a frequency of 1-100 MHz.
-
Product
8-16-24 Ports Video Recorder
-
NVS series of video recorder with 8-16-24 802.3af/at Compliant PoE can be applied to usage cases like banking, healthcare, building surveillance, etc.
-
Product
SparkFun Qwiic Thermocouple Amplifier
MCP9600 (Screw Terminals)
-
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
Product
Converter Signal Amplifier – 0…10 Vdc – Wall Mounting
HD978TR6
-
Configurable converter signal amplifier with 0…10 Vdc (10…0 Vdc). Input measuring range -10 ..+60 mVdc. Standard configuration 0…20 mVdc. Minimum measuring range 2 mVdc.
-
Product
C-Band Separate Raman Fiber Amplifier
RFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
Product
High Voltage Linear Amplifier
A800X
-
This unit is a version of A800 amplifier equipped with two inputs, DC-offset and output atenuation. Input A is a normal non-inverting one. Using this input alone makes A800X functionally identical with A800 amplifier.Input B can act as a inverting or non-inverting depending on the position of the corresponding switch.
-
Product
Erbium Doped Amplifier
AEDFA-FTTH
-
Amonics FTTH EDFAs inherit the reliable design of Amonics's optical amplifier technology. They exhibit high output power, high gain with very low noise, and are ideal for FTTH network amplification. Integrated CWDM splitters are available to enable routing of 1310nm and 1490nm data streams from OLT to ONU through EDFAs. The turnkey rackmount EDFAs provide microprocessor controlled alarms and status indicators. An integrated Ethernet TCP-IP computer interface enables easy control, diagnostic functions and data acquisition.
-
Product
In-Line Charge Amplifiers
-
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
Product
Optical Limiting Amplifiers
-
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
Product
LVDT Sensor Amplifiers
-
Analog Devices signal conditioning ICs, together with linear variable differential transformers (LVDTs), can be used to convert mechanical position to a dc voltage. The IC provides both the excitation for the LVDT and the output conversion to dc level with a user selectable gain. ADI LVDT signal conditioners are available to interface with a wide range of LVDTs, including half bridge and standard 4- and 5-wire.
-
Product
Low Noise Amplifiers
-
RPG Low Noise Amplifiers are developed and manufactured using the most modern discrete components and thin film technologies, in order to cover the frequency range 50 to 350 GHz. With improved DC-supply and modern semiconductors these amplifiers not only deliver low noise performance but also broad operating bandwidth and gain flatness. These low-noise amplifiers are available as a standard product and on request as customized manufactured product.
-
Product
PPID-2000 Photosynthetic Photon Intensity Distribution Test Unit
-
Hangzhou Everfine Photo-E-Info Co., LTD
It is mainly used for testing plant lighting products. With the EVERFINE GO-R5000 goniophotometer system, it can realize the measurement of plant photosynthetic photon intensity distribution (μmol/s/sr) in the whole space. In addition, the device can also realize the test of photosynthetic photon flux, far red light photon flux, photosynthetic radiation efficiency and other parameters, referring to DLC, ASABE, DIN, GB, CQC and CSA related international plant lighting standards .
-
Product
2.5G Distributed Feedback Lasers
-
Macom Technology Solutions Holdings Inc.
MACOM’s Distributed Feedback (DFB) laser diodes are designed for direct modulation uncooled operation up to 2.5Gb/s. These products utilize patented Etched Facet Technology (EFT) for exceptional reliability with the following benefits: *Etched Facet Technology enabling high performance and product uniformity*Wide operating temperature range for wireless, PON and datacenter applications*No isolator required due to high back-reflection rejection
-
Product
GHZ-Wideband Amplifiers
-
Ultra-wide bandwidth from 10 kHz up to 2.5 GHzGain up to 60 dB (x 1,000)Transimpedance gain with photodetectors up to 50,000 V/AVery low input noise down to 310 pV/√Hz (6.2 pA/√Hz)Integrated DC-current path for biased photodetector applicationsTwo identical signal outputs (HSA-Y series)DC-monitor output (HSA-Y series)
-
Product
Driver Amplifiers (< 3 W)
-
Qorvo's driver amplifiers are designed to provide good linear or efficiency performance for gain stages prior to the final power amplifier in a transmitter chain. These products support frequencies up to 46 GHz, using process technologies such as InGaP HBT, power pHEMT, E/D pHEMT and GaN.
-
Product
RF High Power Broadband Amplifiers
-
Chengdu KeyLink Microwave Technology Co., Ltd.
Broadband amplifiers of KeyLink have exceptional RF and Microwave performance. These RF broadband amplifiers(wideband amplifiers) are available in wide frequency bands from 1 MHz to 18 GHz. Power levels for octave and multi-octave designs range from 1 watts to over 1000 watts. Applications of these broadband RF amplifiers range from radar, jamming, communication to test and measurement.
-
Product
Solid State Power Amplifier Module (SSPA)
-
Macom Technology Solutions Holdings Inc.
MACOM’s Solid State Power Amplifier (SSPA) and waveguide module product portfolio leverages our world class MMIC technology and system design expertise for high performance Industrial, Aerospace, Defense, and Communications applications. Our SSPA modules feature up to 16 power-combined MMICs in a single module and we can power-combine multiple modules up to 100GHz featuring either coaxial or waveguide interfaces.
-
Product
RF Amplifier
SA812C
-
Hangzhou Softel Optic Co., Ltd.
SA812C1/SA812C2 Field Bidirectional AGC Amplifier is a new high gain amplifier. Adopt optimized circuit design and scientific and rational process. High performance AGC control circuit inside is useful for stable gain and low distortion. It's the best choice for large and medium-sized bidirectional CATV transmission network.
-
Product
10mA One-Channel Amplifiers
-
USB connected devices have become common in lab environments. The nano box USB is a standalone piezo amplifier with 16 bit D/A resolution. Its small size and powerful amplifier includes a USB 2.0 interface that offers a variety of helpful commands.
-
Product
Instrumentation Amplifier
AAF-3G
-
Programmable, 2-Channel Instrumentation Amplifier for the AAF-3, AAF-3PCI, PGA-16 and OEM Data Acquisition Systems.
-
Product
Distribution Operations
-
Schweitzer Engineering Laboratories, Inc.
SEL provides tools that work with protection and control relays to improve your system’s visualization and dynamic response—while still maintaining performance, situational awareness, and efficiency.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
