Filter Results By:
Products
Applications
Manufacturers
Volt Drop
electrical energy given up flowing through a circuit.
-
product
Mezzanine System
5658
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
-
product
Digital Multimeters
ST-3501
Standard Electric Works Co., Ltd
● Display: 3½ digit liquid crystal display (LCD) with max. reading of 1999.● Polarity: Automatic, (-) negative polarity indication.● Zero Adjustment: Automatic.● Over Range Indication: Highest digit of (1) or (-1) is displayed.● Low Battery Indication: The (BAT) is displayed when the battery voltage drops below the operating voltage.● Measurement Rate: 3 measurements per second, nominal.● Operating Temperature: 0°C to ±50°C, 0-70% RH.● Storage Temperature: -20°C to +60°C, 0-80% RH, with battery removed.● Accuracy: Accuracy specifications at 23±5°C, less than 75% RH.● Power: Single, 006P 9 volt battery● Dimensions: 128(L)×72(W)×33(D)mm.● Weight: Approx .200g
-
product
PoE Tester
PE-100
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
product
Load Cell Power Supply
MODEL PSMR
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
product
Audio Multimeter
AMM-1
The purpose of this tool is to enable the user to: Measure True Amplifier Power output into any load reactive or resistive Measure Common DC voltages Measure DC voltage drops during quick transients on cable runs or battery / charging systems Measure Impedance of speakers at any power or frequency from 20Hz - 1kHz (box rise) Measure Phase Difference between Voltage and Current into reactive loads (Power Factor) Find Tuning Frequency of subwoofer enclosures Tune subwoofer enclosures for maximum power transfer Measure AC Volts (amplifier output) Measure AC Amps (amplifier output)
-
product
Milli Volt Drop Test Set
Widely used for testing transformer and switchgear, this equipment is available to clients in different capacities.
-
product
4 Digit Field Indicator
CFIA-40 4
Chuan Sheng Electronics Co., Ltd.
1. Using LED to display, and able to be used in dark environment2. No external power needed3. Able to display measured value like pressure , temperature and depth etc4. Display solution 1/99995. Isolated alarm open drain output6. Voltage drop will below 4 volt
-
product
Digital Multimeters
ST-3201
Standard Electric Works Co., Ltd
● Display : 3½ digit liquid crystal display (LCD) with max. reading of 1999.● Polarity : Automatic, (-) negative polarity indication.● Zero Adjustment : Automatic.● Over Range Indication : Highest digit of (1) or (-1) is displayed. ● Low Battery Indication : The (BAT) is displayed when the battery voltage drops below the operating voltage.● Measurement Rate : 3 measurements per second, nominal.● Operating Temperature : 0ºC ~ 50ºC, 70% R. H.● Storage Temperature : -20ºC ~ 60ºC, 80% R. H.● Accuracy : Accuracy specifications at 23 ± 5ºC, less than 75% R. H.● Power : Single, 006P 9 volt battery● Dimensions : 128(L) × 72(W) × 33(D) mm.● Weight : Approx. 183g
-
product
Battery Monitor
BAF-M2
Schumacher Electric Corporation
BATTERY MONITOR• Plugs into a 12 volt automotive cigarette lighter receptacle• Allows instant monitoring of battery & charging system voltage• Constant automotive battery and charging system check with a digital readout• LED warning lights alert you when your battery or charging system is not functioning properly• Detects charging input voltage within 0.1 volts variance• Detects problems with the alternator, diode and any variance of more than 0.8 volts• Alerts you once battery drops to 12.0 volts giving you approximately one more hour of run time, depending on the system’s wattage• Digital display indicates electrical voltage of your battery• Mounted display on your car’s dashboard for constant monitoring of your electrical system Contents: (1) Battery Monitor with 12V DC plug
-
product
RF Volt Meters
The latest addition to Boonton’s popular 9200 series of RF voltmeters. It combines accuracy, smart probes, and operator features that have never before been available in its price range.
-
product
Transducers with 0-10 Volts Output
Overview of transducers with 0-10V output for temperature, humidity, CO2 and pressure.
-
product
Drop Test Machine
Single-wing Drop Test Machine Simulate the drop conditions of packaged products when different faces, edges and corners fall to the ground from different heights, thus to understand the damage of the product and evaluate the drop height and impact resistance that the packaging materials can endure while falling down, so as to improve and optimize package design according to actual conditions of the product and national standard range.
-
product
Millivolt Drop Tester
The SCR ELEKTRONIKS Millivolt Drop Tester is an industry acclaimed product. MVDT has a specially built constant current source (current generator) up to 400A (depending on model) and a dedicated PLC to store test parameters (in automatic models), perform test procedure, make the millivolt drop & junction resistance measurements and store test results, that can be retrieved later or downloaded to PC. PC based TestWare can display the test results & export those to Office, HTML, Printer or PDF. The manual models consist of the constant current source, digital ammeter and a digital millivolt meter with 3 ranges.
-
product
Zero-distance Drop Test System
KRD40 series
KRD40 series drop tester, mainly simulates the resistance to drop and impact of large and heavy packaging products. Its strong power system and unique sample holder facilitate easy loading and unloading of oversized and overweight items and automatically rise to the setting. After the height, the drop test is completed. It can realize the drop test of the edge, surface and angle of the sample. This equipment is mainly used to evaluate the ability of product or packaging to withstand drops during transportation and loading and unloading, so as to improve product and packaging design.
-
product
0-10 Volt Sensor
DT140
A general sensor that will measure any device or transmitter that produces a linear analog 0-10V output. The voltage can easily be converted to the correct measured units with the help of the Microlab program.
-
product
Volt Probe & Socket Testers
Non-Contact & Socket
Use Amprobe non-contact volt probes to safely check circuit breakers, wall sockets and fuses for voltage presence with portable, economical tools. For sockets, choose an Amprobe socket tester, which can confirm whether GFCI breakers are properly wired.
-
product
Small Drop Test System
KRD41 series
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
product
Shock & Drop Testing
Shock testing is often performed as part of a hardware qualification or design process. Information obtained during shock testing can improve the survivability of products as well as verify that they will perform properly in service. These types of tests require special transducers and measurement systems to record and process the high level, high frequency response.
-
product
Service Drop Locator
VM-560
The VM-560 is a general-purpose locator used to detect buried pipe and cable services in a variety of situations. With a 50/60Hz passive power locating frequency and three active frequencies, the VM-560 locator will meet the requirements of those wishing to detect the presence of active power cables and to trace short ranges. The VM-560 transmitter also has the additional frequency of 8kHz Fault-find so it can be used to detect the presence of ground to sheath faults on cable when used with the VM-510 Stand Alone A-Frame fault locator.
-
product
Spinning Drop Tensiometer
SDT
Our Spinning Drop Tensiometer – SDT measures interfacial tension with a high degree of accuracy and a particularly wide measuring range. The SDT is the ideal solution for the quality control and development of emulsions and surfactants thanks to its enormous bandwidth, small sample volumes and simple handling during preparation.
-
product
Automatic Double Drop Test Machine
DT-JT
The machine wills automatic stop positioning after sample reach up to the sated height position. According to the different size to choice the test distance between tests arms, electric pulse width. The release mechanism of machine are flexible and reliable, to ensure the sample without any external influence during the release of instant and free fall way, and make sure it meet sample’s dropping requirements. It is according to GB4757.5-84), GB/T4857.5-92, GB/T2423.5, IEC68-2-27, JISZ0202-87, ISO2248-19, ISO2248-1985(E, ASTMD5276-1998 and ISTA3A. This series drop test bench for measuring the main simulation packages in the transportation, loading and unloading process under drop impact influence, identification package impact strength and packaging design.
-
product
Ultra Stable Surface DC Volt Meter
USSVM2
The meter measures the magnitude and polarity of static charge on objects or surfaces. The sensor is calibrated for measuring a surface at 1" from the end of the sensor. On metallic or conductive surfaces, the meter measures the voltage on the surface. (As with any electrostatic voltmeter, the displayed reading depends somewhat on the size of the object being measured and the distance between the object and the sensor.) On insulating surfaces, "voltage" is not a well-defined number. In this case, the meter reads a number proportional to the static charge present.
-
product
Drop Tester
KD-2768
King Design Industrial Co., Ltd.
Drop tester is applied to test the anti-vibration, covering-protection capability of packaging material, or product’s impact-resisting capability to determine the improvement parts of related packing design, material and structure. It contribute to promote the packing material and product’ strength. According to the result of packing drop test, you can judge whether the product has reach the required strength encountered in future. Through doing the drop testing of product independently, you’ll know its affordability to withstand external impact and assess the damage.
-
product
Traction Battery Drop Tester
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Drop Tester Relevant standards requirementsSingle Storage Cell Safety TestDropt testing steps：Charge the single storage cellaccording to 6.1.3Drop the positive negative terminals of the cellfrom the height of 1.5m to the concrete floor；Observe for 1hBattery Module Safety TestCharge the battery module according to the standard 6.1.4Drop the positive negative terminals of the battery from the height of 1.2m to the concrete floorObserve for 1h
-
product
Service Drop Locator & Metal Detector
VM-585
The VM-585 is a combination of the popular VM-550 utility locator with the added benefit of a built in Ferrous Metal Detector. This makes it ideal for locating short distance runs such as service drops and to detect buried ferrous metal objects such as buried valve box covers, buried tanks, and manhole covers. The advanced filtering of the VM-585‘s metal detector rejects materials such as bottle caps and aluminum cans and zeros in on finding only ferrous materials. The manual gain control allows it to be controlled and able to work close to large metal objects such as automobiles and chain link fences while still looking for the targets underground. The VM-585 will locate through asphalt, concrete, or grass and in temporary conditions such as snow.
-
product
Battery Drop Tester for Battery Safety Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's battery drop tester is used to test the drop impact performance of large, heavy-duty packaging products by simulating real surface, edge, and corner differences.
-
product
Digital DC Micro Volt meter
PGP Electronics Private Limited
PGP Electronics Digital DC Micro Voltmeter is a precision measuring tool for the measurement of low DC Voltages. This unit can measure low DC voltages, typically in the order of Micro Volts. This instrument is designed to with stand rugged operation.
-
product
Video Volt Meter
VVM
This hand-held, battery-powered Video Volt Meter measures sync, white and composite video with digital accuracy in volts peak-to-peak and I.R.E. units.
-
product
Volt Gradient Detector
K&S Engineering and Scientific Ltd
The Voltage Gradient Unit is used to pinpoint faults by the pool of potential methods
-
product
Cycle Drop Simulation Generator
Beijing KeHuan Century EMC Technology Co,.LTD
Cycle drop simulation generator
