PCI Diagnostic Cards
See Also: POST Cards
-
Product
PCI Resistor Card 2-Channel 2 Ohm to 32.7k Ohm With SPDT
50-293-132
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
VLF Diagnostics System
PHG 80 TD
-
Cable testing and diagnostics with the BAUR PHG 80 TD. The combination of the PHG 80 programmable test generator with the BAUR dissipation factor measurement system produces the cable testing and diagnostics system PHG TD. It is operated via PC control. Dissipation factor measurement and diagnostic testing sequences can be programmed in the menu, after which the dissipation factor measured values are automatically determined in various voltage steps and a final evaluation is conducted.* Biggest dynamic range of tan delta measured values from 1 to 10-4 with a cable capacitance >10 nF to 20 uF* High resolution +/- 1x10-5 applicable even in new PE/XLPE cables* Insensitive against interferences due to complete mains separation* Lowest time required for assessing a medium-voltage cable (3-phase approx. 1 hour)
-
Product
Counter DAQ Cards
-
Counter card series include pulse output, event counting, PWM measurement/output and encoder reading functions.
-
-
Product
8 Port PCI Express
PEX 8608
-
The ExpressLane™ PEX 8608 device offers 8 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 8 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The PEX 8608 architecture supports packet cut-thru with the industry's lowest latency of 140ns (x4 to x1) and offers two virtual channels for traffic prioritization in the system.
-
Product
20-Port PCI Express
PEX 8680
-
The ExpressLane™ PEX 8680 device is the industry's first PCIe switch to offer 80 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 20 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 80-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including servers, communications, storage, blade servers, and embedded systems.
-
Product
96/48/24-CH Opto-22 Compatible Digital I/O PCI Cards
PCI-7296/7248/7224
Digital I/O
ADLINK"s PCI-7296/7248/7224 are high-density parallel digital I/O boards with 96/48/24 I/O channels. The header connectors are fully compatible with industry Opto-22 standard. Thus, PCI-7296/48/24 can utilize the Opto-22 external devices. The PCI-7296/7248/7224 devices emulate mode 0 of the industry standard 8255 programmable peripheral interface (PPI) chips. The PCI-7296/7248/7224 provides 4/2/1 PPI chips respectively. Each PPI offers three 8-bit ports: Port A, Port B and Port C. The Port C is divided into 2 nibble-wide (4-bit) ports. The PCI-7296/7248/7224 devices have programmable timer/counters. One 16-bit counter is available for event counting, while the other 32-bit timer is available for timed interrupt generation. The PCI-7296/7248/7224 devices provide multiple programmable interrupt sources from DIO channels, as well as the output of the timer.
-
Product
PCI Express Digital I/O Card With Counters And IRQ
PCIe-DIO-24HC
-
This product is a x1 lane PCIe DIO board with basic DIO, Counter/Timers and interrupt generation capabilities. The card uses an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C is further broken into two 4-bit nybbles via software, configured as either inputs or outputs.
-
Product
PCI Express To PCI Express Expansion With 16 PCIe X4 Gen-2 Slots
ExpressBox16-BX4
-
Magma’s ExpressBox 16 is the simplest solution to seamlessly increase the number of PCI Express® slots available to your server or workstation. ExpressBox 16 expands one host PCIe® slot to sixteen slots by extending PCI Express signals over a high-bandwidth x8 or x16 connection to an external Magma enclosure.
-
Product
64-bit PMC to PCI Adapter
4930
-
This passive PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment.
-
Product
Multiprotocol Serial Card
PCIe-COM-4SM DB/RJ
-
ACCES I/O’s PCI Express multi-port multi-protocol serial communication cards deliver four (PCIe-COM-4SMDB, PCIe-COM-4SMRJ) or two (PCIe-COM-2SMDB, PCIe-COM-2SMRJ), high-speed serial communication ports for use in a wide variety of applications.
-
Product
32-Bit CardBus Card
GPIB-PCMCIA-XL
-
The GPIB-PCMCIA-XL is the ideal solution for connecting GPIB instruments to mobile computers.
-
Product
Microwave Switch Cards
-
The Adapt-a-Switch® microwave switch cards deliver high performance and high density for your microwave switching applications.
-
Product
PCI Simulation Modules For Sensor Simulation
-
Does your test strategy require simulating environmental sensors, including temperature, pressure, altitude, and strain gauges.
-
Product
PCI Precision Resistor Card 3-Channel, 3Ω To 5.82MΩ
50-297-152
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Express x4 Copper Cable
ProDAQ 8034
-
The ProDAQ 8034 PCI Express x4 copper cable connects crates equipped with the ProDAQ 3026 Low-Cost PCI Express VXIbus slot-0 interface or the 3030 PCI Express VXIbus slot-0 interface to the ProDAQ 3261 PCI Express host interface. The cable transmits four PCI Express lanes and sideband signals with transfer rates of up to 10 Gbps full-duplex. The robust, shielded cable and the die-cast connectors with latching mechanism ensure a stable connection and prevent accidental disconnects.
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
-
Product
Linear Array Detector Cards
X-Card 0.2 to 2.5mm
-
A product family of high performance linear X-ray detector cards with preamplifier ASICs. The preamplifier ASIC converts the charge output from the photodiode array into voltage with serial output for easy integration with readout electronics. Can be arranged end-to-end to form large linear detector arrays.
-
Product
Compact PCI AE Chassis
MICRO-II
Chassis
The Micro-II is an industrial chassis built to enable powerful AE testing capabilities in a compact form factor. Its 4 PCI slots allow it to hold up to 32 AE channels, using Physical Acoustics’ PCI-8 AE boards. It has been designed to operate either as a benchtop system via direct connection to a monitor, keyboard, and mouse, or as a remote system controlled by a notebook computer over its Gigabit Ethernet interface.
-
Product
Customized Cards & Modules
-
Tap into the resources of both a world-class electronics manufacturer in Molex, and a proven Engineering team that has been designing complex FPGA products since 1993. It’s a unique combination. Our experienced staff, IP, processes and facilities are the ingredients of a world-class design and manufacturing partner that our customers value for their most important projects.
-
Product
Dual-Port Serial Interface Cards
PCI-COM2S And PCI-422/485-2
-
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
-
Product
PCI High Density Resistor Card 10-Channel, 8-Bit, 0 To 255 Ohm
50-295A-021-10/8
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
FPGA Cards
-
Curtiss-Wright Defense Solutions
Curtiss-Wright addresses the demands for increased data and signal processing performance, along with flexible interfaces for handling sensor I/O, through our full line of FPGA processor cards. Our rugged FPGA cards supporting Xilinx FPGA devices are designed to perform reliably in the harshest military environments.
-
Product
GPIB Controller Card
GPIB-PCI-E
Controller
The GPIB-PCI-E is a PCI Express GPIB controller card that converts any PC with a PCI Express slot into a GPIB controller.
-
Product
Isolated Serial Interface Card
PCI-ICM-2S
-
The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
Low-cost Cable/terrestrial Modulator For PCI
DTA-111
-
Low-Cost VHF/UHF Modulator for PCI Bus
-
Product
32 Channel Pass Through Card
SET-2090
-
The input signals can be configured by customers. Each input channel can be tested, conditioned or measured in different ways. Various inductors, filters, pull-up or pull-down resistors can be used for this purpose. In standard configuration, the input signals are transmitted directly to the output.
-
Product
Production Parametric Probe Card
VC20TM Fab
-
*Maximum channel count: 48*Tester platforms: Keysight 4062, 4072, 4080, Keithley S600, S530, Rack and Stack configurations.*Minimum Pad Size: 30ux30u (tunable scrub)*Contact Resistance: less than 1 ohm*Temperature range: -65C to 200C*Leakage: Less than 5 femto Amps per volt. If you require faster settling time*Repairable*Lifetime Performance: Production customers are experiencing 10M+ million touchdowns on Aluminum and Copper pads. Few to no rebuilds due to pobe wear
-
Product
High Speed Matrix Card
MATX4001
-
The MATX4001 module is a general purpose-switching matrix, consisting of 40 relays arranged in 5 rows by 8 columns. Each row/column consists of independent Force/Sense lines that are switched simultaneously. Each relay is capable of handling 1 Amp and can isolate up to 5 KV. Each relay on the matrix is independently controlled with an On/Off command via software
-
Product
High Current Relay PXI Card
GX6115
Relay
The GX6115 is a 15 channel, high current relay board that plugs directly into any 3U PXI slot. The GX6115 also provides three transistor-driven channels for external relays. These outputs may be used to drive external loads, such as heavy duty relays, lamps or other devices.
