Infrared Calibrators
controlled sources of thermal radiation, used to calibrate infrared radiation devices.
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (m)
85562A
Mechanical Calibration Kit
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight
-
Product
CalPod Drive Cable, 40 GHz, 2 Meter
85553A
Calibration Cable
This cable provides the bias voltages and control signals for operation of the 40 GHz CalPod modules. This cable is supplied with the 85540/41/42A CalPod modules.
-
Product
Flexible Cable Set, 3.5 Mm (Test Port) To 7 Mm
85132F
Calibration Cable
The Keysight 85132F is a 62.9 cm (24.75 in) long¹ flexible cable set composed of two 3.5 mm female² to 7 mm connectors. Cable frequency range is dc to 18 GHz with a return loss greater than or equal to 17 dB. Insertion loss is 0.25 * sqrt(f) + 0.2, where f is frequency in GHz, for the test port connector and device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability¹ of the Keysight 85132F is less than 0.12 dB and phase is 0.13 * f + 0.5, where f is frequency in GHz.
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7-16 (female)
85038F
Mechanical Calibration Kit
The Keysight 85038F calibration kit contains only female calibration devices (open circuit, short circuit and termination) and has frequency coverage from dc to 7.5 GHz (usable to 8 GHz).
-
Product
Cal Kit, 4-in-1 OSLT, DC To 26.5 GHz, 3.5 Mm(f)
85521A
Mechanical Calibration Kit
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
Product
Standard Mechanical Calibration Kit, DC To 7.5 GHz, 7–16 (male)
85038M
Mechanical Calibration Kit
Modern wireless communication systems require high-performance components offering low VSWR and low intermodulation distortion at high transmit power levels. To meet these needs, 7-16 connectors are becoming increasingly common in base station transmitters, amplifiers, duplexers, and other products. These connectors conform to IEC 169-4, DIN 47223, European standard EN 122190, and British standard BSEN 122190.
-
Product
15-meter (49 feet) Sensor Cable
E1739C
Calibration Cable
The E1739C 15-meter (49 feet) Sensor Cable is used to connect the E1736A USB Sensor Hub to either the E1737A Material Temperature Sensor or the E1738A Air Sensor. The connectors at either end of a sensor cable are identical. It is part of the 5530 Laser Calibration System. Other cable lengths available: E1739A 5-meter (16 feet), E1739B 10-meter (33 feet) and E1739D 25-meter (82 feet).
-
Product
Linear/Angular Measurement Kit
55281B
Mechanical Calibration Kit
The Keysight 55281B Linear/Angular Measurement Kit is part of the Keysight 5530 Laser Calibration System and enables the system to measure both linear velocity along a machine's travel path as well as rotation about an axis perpendicular to the axis of motion (pitch and yaw).
-
Product
Economy Mechanical Calibration Kit, DC To 6 GHz, 7 Mm
85031B
Mechanical Calibration Kit
The Keysight 85031B calibration kit contains a set of precision 7 mm fixed terminations and a one-piece open/short circuit used to calibrate Keysight network analyzers for measurement of devices with precision 7 mm connectors. This kit is specified from dc to 6 GHz.
-
Product
Infrared Linescanners
-
Fluke Process Instruments Linescanners are designed for continuous monitoring of parts or processes. The up to 300Hz scan speed is the fastest in the business. This provides more complete data about even the highest speed manufacturing processes. With up to 1024 data points per scan and up to 200:1 optics, each spot on the target surface is over sampled up to three times, providing complete coverage.
-
Product
Infrared Thermometers
-
PeakTech Prüf- und Messtechnik GmbH
Infrared thermometers offer many advantages when measuring surface temperatures because they have a much faster response time than conventional contact thermometers and it is possible to record precise measurement results in fractions of a second.
-
Product
Infrared Thermometers
-
Non-contact Infrared Thermometer Sharply Focus on Measurement Spots with Two-Beam Laser Marker, Ideal for HVAC Applications
-
Product
Infrared Thermometers
-
Easily measure surface temperatures with ThermoWorks non-contact IR guns, ideal for produce and agriculture inspectors, HVAC, construction, warehouse, quality assurance, HACCP and cold chain management, both shipping and receiving. Choose from fixed or adjustable emissivity; single, dual or circle laser types; and lens optics from close focus—for electronic components and laboratory measurements—to 100:1—for long distance measurements. High temperature ranges up to 3272°F (1800°C) are perfect for metallurgy and metal work foundries.
-
Product
Infrared Thermometer
DITH 120
-
Infrared Thermometer is also known as laser thermometerInfrared thermometer is a thermometer which infers temperature from a portion of the thermal radiation sometimes called blackbody radiation emitted by the object being measured.Laser is used to help aim the thermometer or non-contact thermometers or temperature guns, to describe the device's ability to measure temperature from a distance. By knowing the amount of infrared energy emitted by the object and its emissivity, the object's temperature can often be determined. Infrared thermometers are a subset of devices known as "thermal radiation thermometers".The design essentially consists of a lens to focus the infrared thermal radiation on to a detector, which converts the radiant power to an electrical signal that can be displayed in units of temperature after being compensated for ambient temperature. This permits temperature measurement from a distance without contact with the object to be measured. A non-contact infrared thermometer is useful for measuring temperature under circumstances where thermocouples or other probe-type sensors cannot be used or do not produce accurate data for a variety of reasons.
-
Product
Waterproof Infra-Red Turbidimeter (NTU) with calibration kit
TN 100
-
The microprocessor-based waterproof TN100 meter is an easy-to-use turbidimeter that meets the rigor of rugged field applications. It is a "must -have" for anyone monitoring turbidity on the go. Using an Infrared light source, it delivers laboratory accuracy with a resolution of 0.01 NTU across an extended range of up to 20 NTU (Nephelometric Turbidity Units).
-
Product
Calibration
EMC Test Antennas
-
There are some changes in the calibration standard ANSI C63.4 concerning the calibration procedures of hybrid antennas, also the newly issued standard - CISPR 16-1-6 dealing with EMC antenna calibration is covered by our services. You are very welcome to consult Seibersdorf Laboratories calibration experts for the recommended calibration procedures of the most common radiated emission test standards.
-
-
Product
Calibrators
-
TES Electrical Electronic Corp.
Unique mapping function let you calibrate temperature. iCal is a multifunction calibrator and an arbitrary function generator.
-
Product
Calibration Lead Precision Resistor - Single
40-975-009-SL1
Calibration Lead Cable Assembly
The cable assembly is specifically designed to connect to the 9-Pin D-Type calibration port located on the front panel of Pickering Interfaces Module Part Numbers 40-260, 40-261, 40-262, 40-263 and 40-265.
-
Product
Far Infrared Systems
-
Far-Infrared and terahertz (THz) radiation is the spectral region at the long wavelength end of the infrared and the short end of the microwave region, also known as the sub-millimeter wavelength spectral region. Recently, there has been an explosion of interest in THz applications as the radiation generated can penetrate various materials. THz light is commonly used in materials science, security, pharmaceutical com- pound analysis, biomedical imaging, superconducting materials, astronomy, and particle physics research.
-
Product
Infrared Thermometer
64 MAX
-
Fluke 64 MAX IR Thermometer features Auto Capture allowing technicians to set time and intervals to record up to 99 data points unattended so it can capture elusive temperature events. The thermometer can be mounted on a standard tripod using a tripod mount accessory for unattended measurements. The 64 MAX displays minimum, maximum, or average temperature, or the difference between two measurements, and features Hi and Lo alarms for rapid display of measurements outside set limits.
-
Product
Infrared Cameras
-
Nowadays, temperature measurement is closely linked to this new type of equipment, capable of fully mapping any kind of surface. HT offers a wide range of Infrared Cameras for any kind of requirement and use.
-
Product
IR Infrared Thermometers
-
Includes the GM300 and GM700, a great Value Hand Held Instrument in hard case with battery included. Also includes the RayTemp 2 and IR Micro Thermometer.
-
Product
Calibration Standards, Calibration Services
-
ISO 17015 traceable calibrated reference lamps, detectors and reflectors for the calibration and adjustment of sensors and measurement devices for light, optical radiation and light reflection. We offer as well many ISO 17025 calibration services.
-
Product
Infrared Thermometers
-
Makes non-contact temperature as quick and easy as pointing the laser and pressing a button. Unique pocket-sized model available with additional temperature and flashlight feature-set.
-
Product
Infrared Thermometer
EST-65
-
*High quality construction w/rubber insert in grip, nose & LCD areas. *High temperature range
-
Product
Infrared Thermometer
6574
-
Peaceful Thriving Enterprise Co Ltd
*Distance to spot ratio is 8:1.*Temperature range: -50-550℃.*Laser and Low Battery indicator.
-
Product
Infrared Thermometer
MT-4612
-
Ideal for measuring of mechanical, chemical, pottery,food, metallurgy, electric power, air condition,high-temperature heat treatment.
-
Product
Infrared Thermometers
-
Our infrared thermometers make it possible to measure a temperature without contact by way of determining an object emitting infrared radiation. Here you will find Infrared Thermometers for measuring temperature without contact and contain a targeting light to ensure the correct surface area is being measured. An infrared thermometer can only measure the temperature of exposed surfaces and not through glass. Some infrared thermometers possess a preset emissivity value, and others allow the user to choose the emissivity value depending on the surface material being measured, whether it's paper, wood or metallic surfaces.
-
Product
Non-Contact Infrared Thermometers
-
Precision Mastech Enterprises Co.
Handheld devices that measure surface temperature from a distance by detecting infrared radiation emitted by an object.
