Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Cable Assembly, 50-Pin D-Type, Female to Female, 0.5m HV, Exit Away From Pin 1
40-970-050-0.5m-FF-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Proactive Downstream Spectrum Analysis
SpectraVizion
SpectraVizion is an innovative, software-based diagnostics tool that leverages new advancements in remote spectrum capture, allowing cable operators to address downstream spectrum impairments proactively, before subscribers call in with service complaints. “Troubleshooting downstream spectrum issues has always been a reactive process for cable operators,” said Arthur Skinner, Vice President of Worldwide Sales for ZCorum. “Often they’re not aware they have an issue until a customer calls, and that’s when they then send a technician to the home with a hand-held meter to start a search for the problem.” SpectraVizion takes the guesswork out of problem identification and location by presenting on a simple dashboard a list of devices that are experiencing common downstream issues like Standing Waves, FM Noise, Suck-outs, Roll-off and Tilt. The tool leverages the spectrum data available from cable modems and set-top boxes that support full band capture, and advanced detection algorithms automatically identify devices experiencing downstream impairments. The operator can click on any device in the list to view a capture of the full spectrum from that day, or up to 30 days in the past.
-
product
Power Special Test Equipment
PSTE
AMETEK Programmable Power, Inc.
There are several key benefits of the PSTE. First, it is a complete turnkey system that is capable of operating locally through a simple GUI interface or remotely via a host computer as a single Ethernet address. The spacecraft engineer who defines the spacecraft power bus limits, cabling scheme, mode simultaneity matrix, and system behavior based upon limit conditions implements the real intelligence of the system. From this definition, operating procedures can be generated to allow spacecraft technicians to operate the system, system protections are implemented that perform cable detection and mode verification, automated spacecraft fixture identification and related mode capability, and more.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Female, 0.5m
40-971B-200D-0.5m-MF
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
Cable Fault Locator
TX2001
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3000m (10,000ft) 50, 75 & 100 ohm Selectable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
product
Multi-function Cable Tester
NCT-100-S
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
product
Handheld Online PD Detector
PD-SGS
BAUR Prüf- und Messtechnik GmbH
Quick identification of PD activities in switchgear and cable accessories. The BAUR PD-SGS handheld online PD detector is used to conduct rapid initial tests for PD activities on live switchgear. Potential weak points are immediately signalled acoustically and numerically.* Initial rapid condition evaluation of switchgear and cable accessories during mains operation* Ideal for quick checks of MV and HV switchgear* Two integrated sensors:TEV sensor records PD on the surfaces of switchgearsAcoustic sensor records PD inside switchgears* Greater safety for test personnel switchgear tested for safety risks before starting work
-
product
Low Frequency Generator
LFG-50
• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Cable Identifier
K&S Engineering and Scientific Ltd
K&S Engineering and Scientific LTD's Cable Identifier Set offers the user a compact, portable solution for cable identification. Depending on the user preference, the Cable Function Generator and Cable Identifier Unit can be jointly housed in a rugged briefcase, or alternatively, for the user requiring a more rugged unit, can be delivered as two individual units each with their own carry-case. With the Cable Identifier Set, power optimum levels are selected by means of a rotary switch and the power levels are displayed on a meter located on the Cable Function Generator. As the Cable Identifier Unit is capable of detecting magnetic fields around mains cables it has the added advantage of the user being able to use this as a stand-alone unit to detect power cable configuration.
-
product
Visual Fault Locators
*Visual Fault Locator, we can understand its function in the letter. It could be regarded to be part of OTDR and the fiber fault locator is cheap.*Fiber visual fault locator is a kind of device which is able to locate the breakpoint, bending or cracking of the fiber glass. It can also locate the fault of OTDR dead zone and make fiber identification from one end to the other end. Designed with a FC,SC,ST universal adapter, this fiber testing red light is used without any other type of additional adapters, it can locates fault up to 10km in fiber cable, with compact in size, light in weight, red laser output.*Fiber visual fault locators include the pen type, the handheld type and portable visual fiber fault locator. Fiberinthebox also supply a new kind of Fiber laser tester/ optical fiber pen/ fiber laser pen, it can locates fault up to 30km in fiber cable.*Welcome to our store. Contact us at sales@fiberinthebox.com or Live Chat with us. Save your money & time right now! Buy from optical fiber supplies at Fiberinthebox.com with your confidence.
-
product
Cable Identification System
KSG 200 / KSG 200 T
BAUR Prüf- und Messtechnik GmbH
Cable identification withBAUR KSG 200. The KSG 200 cable identification system is used to identify single- and multi-core cables in a cable bundle or cable loom. By using the KSG 200, the risk of accidentally cutting a live phase is significantly reduced.* Cable identification on all types of de-energised cables* Reliable verification of the cable identification by means of the highly precise three-factor-analysis ATP* Safe cable identification on live low-voltage cables* Connection technology according to CAT IV/600 V
-
product
Leeb Hardness Tester
HT6561
Product synopsis1.1 Typical Applications* Die cavity of molds* Inspection of bearing and other mass produced parts on aproduction line* Failure analysis of pressure vessel, steam generator andother equipment* Inspection of installed machinery, permanent parts ofassembled systems and heavy work pieces.* Testing surface of a small hollow space* Material identification in the warehouse of metallic materials* Rapid testing in large range and multi-measuring areas forlarge-scale work piece1.2 Testing Features* Palm size for narrow space.* Test at any angle, even upside down.* Direct display of hardness scales HRB, HRC, HV, HB, HS,HL.* Large memory could store 250 groups including singlemeasured value, impact direction, material and hardnessscale etc.* User recalibration function allowed.* Can communicate with PC computer for statistics andprinting by the optional cable.* Manual or automatic shut down.* Low battery indication.1.3 Technical SpecificationsDisplay: 12.5mm LCD with back lightAccuracy: Display error ±0.8% at LD=900Measuring range: 200-900LConversion: HL-HRC-HRB-HB-HV-HSDMaterials: 9 different common materialsWith RS232C interfaceMemory: 250 data can be stored and re-readableImpact device: D Will handle the majority of hardness testingapplications. Weight: 75gPower supply: 2x1.5V AAA size batteryDimension: 146×65×36mmWeight: 130g (not including batteries)Working temperature： - 10℃～＋50℃Storage temperature：- 30℃～＋
-
product
LAN Tester
RJ45
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Female, 1m
40-971B-200D-1m-MF
This male rear exit to D-type 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
LAN Tester - RJ45, Coax, Tone
CZ20350
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Deci-Center™ Jumpers
Series 112, 113 & 114
Deci Center Jumpers. Reliable, electronically tested solder connections. Pitch bars help maintain .100 [2.54] conductor spacing. 10-color cable allows for easy identification and tracing.
-
product
Pentype Visual Fault Locator
RA3105
Radiasun International Group Ltd.
The RA3105 Pentype VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes: Finding the breakpoint, poor connections, bending or cracking in fiber optic cables. Finding the faults of OTDR dead zone End-to-end visual fiber identification.
-
product
Energized Cable Identification System
LCI™
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
product
Wires and Pipe Locator
LKZ-720
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
product
LAN Cable Multifunction Tester
TCT-2690PRO
LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.
-
product
COAX & LAN Cable Mapper PRO
PK-801 Multiple 10-Way PRO
The multiple 10-way PRO combines the functions of a 10-way COAX cable mapper and LAN cables identifier that enables identification of a group of improperly labeled patch cables quickly and effortlessly. It also built-in 2 selectable Net/Tel tones for tracing active Ethernet cables even when connected at a switch or Router and locating live phone line systems. This unit also with the capability to do cable/wires loopback and remote continuity testing and voltage detection and warning on F connector, and auto power off function as well as over voltage protection up to 60VAC in a single unit. It provides 2 different ways of Net Tone and HUB blink (optional) feature to trace and work on a live network. It no needs disconnection cable from switch or server and speed up port identification.
-
product
Phase Detector
Paula
BAUR Prüf- und Messtechnik GmbH
BAUR paula phase detector. The paula phase detector is used for clear phase identification in earthed and shorted medium and high-voltage cables. With the help of the measurement procedure tried and tested over many years, paula delivers precise phase allocation without scope for interpretation and corresponds to the highest safety standards for tasks on and close to electric equipment.* Clear phase determination possible in cable lengths up to 40 km* Highest level of safety when used on earthed and shorted cables in compliance with EN 50110-1 (DIN VDE 0105-100)* Suitable for all switchgear constructions due to compact design of the signal injectors* Ready for operation for up to 2 weeks (standby mode)
-
product
Cable Sheath Fault Location
Locating cable sheath faults is one of the last steps in cable testing, occurring after you have identified the existence of a cable fault via the identification procedure based on your specific site variables and the type of system you are working on
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin D-Type Male, 0.5m
40-971B-200D-0.5m-MM
This male rear exit to D-type 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin male D-type connectors. The connector can be secured to the product by screwlocks. The cable assembly can be used with Pickering's 50-Pin D-Type connector blocks (refer to 90-005D). Each of the four D-type cables is numbered to allow identification.
-
product
Online PD Spot Tester
Liona
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR liona. Liona is a portable online PD spot tester for measuring and locating partial discharges in cables and switchgear during normal mains operation. Liona lets you test cable systems and electrical equipment online without switching off partial discharge activities, and then generate trend analyses. Even a PD spot test (duration: 5-10 minutes) is capable of reliably assessing the current status of your system.* Automatic PD detection during normal mains operation (without switching off the cable route)* With DeCIFer technology: PD identification based on 500 million measurement results* Precise online PD mapping with PD transponder
-
product
Cable Tracer and Phone Tester (2 in 1)
183 CB
Standard Electric Works Co., Ltd
Cable Tracer● Trace wires or cables.● Volume control.● Tip & Ring identification.● 2 bi-colored LEDs ( Line 1 & Line 2).● Tone speed selection : Fast & Slow.● A phone jack is designed for headset or handset. (Amplifier probe)Phone Tester● Continuity and resistance testing for voltage-free objects.● Check direct and alternating voltages.● Testing capacitors.● Testing diodes.● Power ON/OFF switch.● The indication of the LED lamp and the sound of the buzzer can occur at the same time.● The LED indication for Power ON status.
-
product
Cable and Pipe Locator
PT-14
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Fiber Identifier
Fiber identifier is an essential installation and maintenance instrument which can identify the optical fiber by detecting the optical signals transmitted through them,during this process the fiber optic identifier generate no harm or damage to the fiber cable and it do not need opening the fiber at the splice point for identification or interrupting the service.This fiber identifier detects frequency tones at 270Hz, 1KHZ, 2KHZ, when traffic is present on the fiber under test, an audible tone can be heard. In the meantime, it can identify the traffic direction that indicated by LED with illumination.
-
product
DIP Jumpers
Series 100 thru 111
DIP Jumpers. Aries offers a wide array of DIP jumper configurations and wiring possibilities for all your programming needs. Protective covers are ultrasonically welded on and provide strain relief for cables. 10-color cable allows for easy identification and tracing.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
product
DataComm & LAN Testers
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
