Analogue
representation of a signal that varies over an infinite range of values.
-
Product
Standard Type Externally Modulated Optical Transmitter
HT8500H
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1550nm externally modulated optical transmitter is the core equipment in the RFTV network system.RFTV is a unidirectional analogue and digital video broadcast. It adopts high efficiency modulation mode for RF carrier wave and its economy , flexibility and bandwidth validity is beyond comparison of IPTV. By adopting EPON, GEPON or P2P access mode to realize triple-play and FTTx, RFTV broadcasting network in 1550nm optical wavelength still plays an important role.
-
Product
47~862MHz & 950~2600MHz Satellite TV & Analog TV PIN Optical Receiver
HRS-26A
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HRS-26A optical receiver, adopting high-sensitivity PIN detector, Taking the technology of frequency division multiplexing, it can receive analogue CATV and SAT-IF signal with the frequency of 47~862MHz and 950~2600 Mhz over single fiber. It can be compatible with any FTTx PON to realize triple-play of analog TV, Digital TV (DBS-C, DBS-T), Satellite TV, Internet and FTTH.
-
Product
Analogue (1kV below) Insulation Tester
1131 IN
-
Standard Electric Works Co., Ltd
● Hight quality Taut Band movement.● Three insulation test voltages (DC) : 250V, 500V, 1000V.● Two ranges for continuity test : 2Ω & 20Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600Vac.● 200mA continuity short-circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
Product
Luminance Colorimeter
XYL-VI
-
The XYL-VI Luminance Photoelectric Colorimeter changes the traditional structure thoroughly, employs the digital X(λ), Y(λ), Z(λ) sensors to replace the traditional analogue sensors, employs the digital signal measurement system to replace the traditional analogue measurement system. The instrument has no analogue unit, thus it is very simple to overcome the zero drift that is impossible to be avoided in traditional colorimeter. The digital sensor has a large dynamic range. Moreover, it possesses strong anti-interference ability and it has high accuracy. The XYL-VI Luminance Colorimeter contains internal RS232 computer interface. The calibration is done by software. It is suitable for monitoring and remote applications. The XYL-VI Luminance Colorimeter can be calibrated by XYL-VI Luminance Colorimeter software to sample the data and print out the results. It can also be corrected by other standard light sources to obtain very high measuring accuracy of x, y color coordinates and color temperature. It is a real-time measuring system and run under Windows2000/XP.
-
Product
Wireless Pulse Input Transmitter Module
T24-PA
-
The T24-PA transmitter module collects and processes pulse related measurements, such as speed of rotation, proximity, flow and count, forming part of the T24 modular telemetry system. The data transmitted by the T24-PA can be received by multiple T24 receivers that include displays, handheld readers, analogue outputs, relay modules and computer interfaces.
-
Product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Intelligent Digital Multimeter, Calibrated, 3999 Count, Mean Value, Auto, Manual Range, 3.75 Digit
72-7755 CAL
-
The 72-7755 CAL from Tenma is an intelligent digital multimeter. It has auto range or manual range options and dual display with maximum reading 3,999 displayed in 40 analogue bars in scale making the measured value to be seen clearly and indicating the trend of changing quickly. In addition to conventional measuring functions, there is a new breakthrough in frequency test with maximum range of 400MHz. RS232C standard serial port is equipped with meter for easy connection with computer to realize macro recording and monitoring and capture of transient dynamic data, displaying change of waveform during measurement, providing data and evidence to engineering technicians for scientific research. This is also a highly applied digital multimeter of high performance with full input protection and display backlight. The orange and grey colour meter features 73mm × 50mm size LCD, CAT III 1000V and CAT IV 600V safety ratings.
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Module For PCI
APXX1553-x
-
MIL-STD-1553 Test and Simulation Module for PCI with 1, 2 or 4 Dual Redundant channels (APXX1553-1, APXX1553-2, APXX1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APXX1553-x module is the option for the MILScope™ capability. Models APXX1553-1-DS/APXX1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
3 Wire (Analogue) Earth Resistance Tester
2105 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
Product
Turbine Flowmeters with Analog Output
CT600R, CT800R Analogue Series
-
High accuracy turbine flow meters with built-in loading valve and analogue output, for use with hydraulic fluids. Flows up to 800 lpm (210 US gpm).
-
Product
Hipot
AC, DC, AC and DC
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Panel mounted controls & indicators with easy to read legend.• Continuously variable output from zero to full voltage.• Low end ground test.• Multi range analogue kV meter and current meter.• Fast acting overload circuit breaker.• Zero start interlock.
-
Product
Gas Detectors
-
International Gas Detectors Ltd
We offer a vast and versatile product range with detector heads for every possible environment. Pioneering the use of addressable gas detection systems IGD today offer the latest networked systems. Our latest addressable gas detection systems network using IGD’s Sentinel+ 2-Wire protocol for enhanced operation and security. IGD is the home of addressable gas detection but we still offer legacy analogue detectors used to interface to older systems.
-
Product
DIGITAL MULTIMETER, TRUE RMS, 10A, 1KV
72-13570
-
*True RMS digital multimeter with 40000 counts display*CAT III 1000V, CAT IV 600V safety rating*Manual function select and auto ranging*Measure AC & DC at the same time (AC+DC)*Up to 9999 readings data storage and 0.1% to 99.9% duty cycle*Data hold, max/min/relative modes, analogue bar graph*Full icon display, double backlight*USB interface and Bluetooth connection*Powered by 9V (6F22) battery*12-month limited warranty *view Terms & Conditions for details
-
Product
Bench/System Linear Regulated DC Power Supply With Smart Analog Controls, Single, Dual Or Triple Outputs, 48 To 242 Watts, With/without Remote Interfaces
PL Series
-
ingle, dual or triple output modelsModels from 6V/8A up to 60V/1.5ALinear regulation - for the best performanceUltra-compact design - uses up less spaceTrue Analogue controls - for ease of useS-Lock function - instantly lock settingsV-Span function - customize the voltage rangeLow current range and current meter averagingDC output switches and "view limits" buttonSelectable remote sense terminalsIndependent, Isolated Tracking, Ratio Tracking and True Parallel modes on dual & triple modelsHigh current low voltage output on triple output model
-
Product
Bench DC Power Supply, Linear Regulation - Single, Dual Or Triple Outputs, Analogue Control, 30 To 130 Watts, Silent Cooling
EL-R Series
-
Single outputs, 30V/1A, 18V/3.3A, 56V/1.1A, 15V/5A, 30V/3ASingle, dual or triple outputs, 30V/2AIndependent digital voltage and current meters for each output with 4 digit resolutionSwitchable local or remote sensingConstant voltage or constant current operationVariable 1.5 - 5.0V auxiliary output at 2A (EL302RT)Compact design uses less bench spaceSilent fan-free coolingDC output switches, automatic mode indicationRS232 or USB controlled models available (30V/2A single)
-
Product
Microwave Wideband APD-TIA Receivers
MR12 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR12 series microwave wideband optical receiver, adopts high Sensitivity APD diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Analogue (1kV below) Insulation Tester
1126 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ) and AC voltage.● LED indiction for testing insulation.● Highly efficiency and accurate DC-DC converter.● Battery check function.● Compact and lightweight.● AC voltage measurement can be made without depressing the test button.
-
Product
BRI and PRI Simulator
emutel Ultra
-
emutel Ultra is a standalone or rackmount unit that comes in five variants giving 8 BRI, 2 PRI and 8 BRI, 2 PRI and 15 BRI, 8 BRI and 14 analogue or 2 PRI, 8BRI and 14 analogue. emutel Ultra can emulate different country specific networks by adding network personality cards & networks supported include North American, NTT, Euro-ISDN, VN3, ITR6 and BTNR191. Protocol analysis option is also available on emutel Ultra.
-
Product
Analogue (1kV below) Insulation Tester
ST-1503
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ), continuity(Ω) and AC voltage.● Instant operation is possible with a push button, convenient timer is provided with automatic power off after three to five minutes to save the battery power.● LED (red) indication when testing insulation and continuity.● Use of a high efficiency and accurate DC-DC converter.● Most suitable for insulation resistance measurement of electrical household appliances, power line distribution and installation.
-
Product
Analogue (1kV below) Insulation Tester
2132 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test. ● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
Product
Modular Tester For Final Test Of LRU’s
FLEX 50
-
The FLEX 50 is designed for customers that prefer a traditional 19” rack format system. The system can be configured with a range of analogue, digital, mixed-signal, and avionics test modules.
-
Product
HPx-410 PCIe Radar Input Card
-
The HPx-410 is a very high-performance PCI express dual stream primary radar acquisition card, capable of capturing and processing analogue and digital primary radar video from up to two independent radars.
-
Product
Dual Output Digital Lab Series Regulated DC Power Supply – Upto 1280W
-
- 300W to 1280W different combination- High current density.- 19″ rack adaptable -3U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
Product
3 Wire (Analogue) Earth Resistance Tester
4105 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
Product
FMC-LPC I/O Module
FM191
-
Sundance Multiprocessor Technology Ltd.
The FM191-RUA1 has a VITA57.1 FMC-LPC connector and follows the electronics specification and recommendations of the standard but is NOT form-factor compatible and will NOT fit all FMC carriers. Two versions are available. The FM191-R main features are a daughter card which provides 5V-TTL-compatible Analogue and Digital GPIOs that are suitable for robotics, motors and sensor application.
-
Product
Microwave Wideband Direct Modulated DFB Transmitters (without RF Amp)
MT50 (40KHz~20GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT50 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
Product
Single-Functional Testers
MI 3121
-
The MI 3121 SMARTEC Insulation / Continuity is a tester for dead testing of electrical installations. With both an analogue and digital representation of the results, the instrument ensures accurate measurements up to 2000 Ω on continuity and up to 30 GΩ on insulation function. Configurable limits enable a PASS / FAIL evaluation of test results, which is accompanied with the bright red and green indicator lights for comfortable use even in the dark conditions. The MI 3121 is equipped with a built-in charger and has a magnetic holder in order to free up hands for testing.
-
Product
Low Cost Microwave Wideband Electro-absorption DFB Transmitter (without RF Amp)
MT60 (40KHz~33GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MT60 series microwave DML optical transmitter, are able to transmit 33G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 60Gb/s high speed communication system.
-
Product
Economic Type Temperature Indicator
CS1-T
-
CS1-T economic type Temperature Indicator has been designed with high accuracy measurement, display and communication of Thermocouple or Pt100Ω.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Analogue (1kV below) Insulation Tester
4132 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
