Filter Results By:
Products
Applications
Manufacturers
Transceivers
both send and receive a signal.
See Also: Optical Transceivers, Vector Signal Transceivers, SFP, SFP Test
- Pickering Interfaces Inc.
product
PXI Analog Output / Current Loop Simulators
These modules are aimed at simulating industrial control transceivers, utilizing 4–20mA current loops. The modules include built-in relays for shorts and opens functionality enabling fault insertion testing on every channel and also enable slew rates to be programmed so that different sensors can be effectively mimicked.
-
product
PXIe-5785, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785585-01
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
product
*PCIe-5785, 12-Bit, 6.4 GS/s, 2-Channel FlexRIO IF Transceiver Device
785587-02
The PCIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PCIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
product
SparkFun Transceiver Breakout
RS-485
This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485. The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
-
product
Transceiver Driver
S-112
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
product
Vector Network Analyzer Extenders
VNAX
VDI''s VNA Extenders deliver high performance network analyzer frequency extension into the THz range. Models cover 50 GHz to 1,100GHz with additional bands in development. VDI modules come in a variety of form factors and configurations including our original Standard-size Modules and new Mini Modules that reduce volume up to 75%. In addition to our full Transceiver (TxRx) modules, VDI also offers Transmit-Reference (TxRef) modules and Receive only (Rx) modules that deliver optimized performance for specific applications. These modules combine high test port power and exceptional dynamic range to deliver industry leading performance. They are compatible with most network analyzers and can be integrated into probe stations and antenna chambers.
-
product
VNA
ZTXR-Series
The RPG ZTXRxxx millimeter-wave transceivers are optional for the following four-port vector network analyzers:
-
product
Fiber Optic Transceivers
Shanghai Tarluz Telecom Tech Co., LTD
Also known as Optical Transceiver or Optical Module. It is a small packaged device that uses fiber optic technology to transmit and receive data.
-
product
Gigabit Ethernet
10G Transceivers: SFP+, XFP, X2, XENPAK
10G transceiver modules from M2 optics are available in a range of types including SFP+, XFP, X2, and XENPAK. All types meet industry standards and we can offer Cisco-compatible along with other major brands.
-
product
Mini PCI Express
MPCIE-A429
Alta Data Technologies’ MPCIE-A429 Mini PCI Express F1 interface module offers a variety of ARINC-429/575/717 channel configurations with software selectable RX/TX channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 transceiver compatible signal.
-
product
Soil Moisture Sensor
Modbus RS485
This is a contact-less capacitive soil moisture sensor, a continuation of my I2C soil moisture sensor. This particular version of the sensor is suited for more professional installations where long cable runs is a requirement. It adds a local voltage regulator to mitigate the voltage drop and RS485 transceiver to accommodate long wires, also reverse polarity and an additional ESD protection level is added.
-
product
SFP Module
F-3000
The DIAMOND flexos SFP modules (transceivers) make it possible to transfer data via fibre optics. The SFP modules are available for multi-mode and single-mode, Gigabit and Fast Ethernet. The SFPs have metal housings with latches for the simple removal of the module. They are compatible with connector types F-3000™ or LC.
-
product
PXIe-57857, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO IF Transceiver
785586-01
The PXIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PXIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
product
Communications Transceiver
AT-710 VHF
The AT-710 is a self-contained, portable, 760 channel VHF air-band communications transceiver.The rugged, portable case includes an aircraft quality radio transceiver, a universal power supply,internal batteries, intelligent battery charging circuitry, audioamplifier and built in speaker.
-
product
ELT STALKER Vector-finder
VF-121
The Vector-Finder Types VF-121 and VF 121A are unique in the Vector-finder series of direction finding antennas. They incorporate a proven design, electro statically shielded loop sensing element with modern solid state low noise analog and digital technology to allow detection and location of aircraft band signals. Both the VF-121 and the VF 121A incorporate a unique digital modulator which allows the user to more easily home-in on unmodulated carriers. Such cases occur at airports when transmitter may be accidentally keyed on during aircraft overnight layovers. The VF-121 is specifically designed to be used on airport premises where signal strengths are high. To compensate for very strong signals, an integral attenuator is also incorporated to allow the user to operate the unit close-in to aircraft. The VF-121A differs in that a high gain, low-noise preamplifier is utilized with the sensing element in order to hunt signals that may be weak or at a distance. The unit is ideally suited for the location of ELT transmitters in the field. Both units are tunable over the 118 MHz to 130 MHz aircraft frequencies and interface directly to the user’s aircraft band receiver or transceiver via the antenna jack. With the antenna system connected to the receiver, the user will hear the desired signal. If the signal is unmodulated, the digital modulator will generate a tone on the carrier. When the handheld unit is rotated about, an audible null on the received signal or the generated tone will be heard. This null aligns with the axis of the equipment case and represents the direction of the received signal. This direction may be read from the black dial compass mounted on the top of the enclosure. As the response is bi-directional, triangulation may be used to determine the true bearing when the true direction is not known.
-
product
Test Board For QSFP28 Transceiver
EQSFP28
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Transceiver Cable
Transceiver Cables are designed to provide flexibility in connecting a bus to various devices on the PXI, CompactRIO, and CompactDAQ platforms. Each isolated cable includes the necessary transceiver for the bus type. The cables also feature termination resistors that you can enable or disable in software. You can use the NI-XNET driver to program and configure the Transceiver Cables.
-
product
TRC-8546 , LIN Transceiver Cable
783702-03
The TRC-8546 is designed to provide flexibility in connecting a LIN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8546 to the port to support a LIN interface. The TRC-8546 is an … isolated cable that includes the necessary transceiver for the bus type.
-
product
Ethernet Transformers
Pulse’s Ethernet transformers are RoHS compliant and qualified at major PHY suppliers. 100/1000/2.5G/5G/10GBASE-T Ethernet transformer modules are optimized for all major LAN transceivers. All modules provide electrical circuit isolation that meets IEEE 802.3, while maintaining signal integrity needed for the most demanding applications.
-
product
Fiber Transceiver Modules
Optical transceiver (transmitter and receiver) modules convert data signals to and from laser optic light and plug into routers, switches, and fiber host bus adapters (HBA). They provide the transmission of data between transceivers over fiber or optical cables.
-
product
Mini MEMS Tunable Filter With VOA
The Optoplex mini tunable filter described is specifically designed for 100G tunable transceiver analog coherent optics (CFP2-ACO) application. The main purpose of this tunable filter is to suppress the noise to improve the sensitivity and OSNR performance.
-
product
Analysis Application for E84
GCI's industry leading E84 diagnostic software is a powerful, Windows-based graphical analysis application that can upload and analyze data from GCI's E84 Handheld Tester, E84 DLD, and RJ-11 Optical Transceiver products. The E84 Analysis Application can also display the signals of a live material handoff in real-time when connected to GCI's E84 DLD or RJ-11 Optical Transceiver.
-
product
PXI-8431/2 , 2-Port, RS485/RS422 PXI Serial Interface Module
778984-01
2-Port, RS485/RS422 PXI Serial Interface Module - The PXI‑8431/2 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
Fiber Cable, Multimode, OM3, 50m
784184-50
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
PXIe-5841, 6 GHz, 1 GHz Bandwidth, RF PXI Vector Signal Transceiver
786982-01
6 GHz, 1 GHz Bandwidth, RF PXI Vector Signal Transceiver - The PXIe-5841 is a vector signal transceiver (VST) with 1 GHz of instantaneous bandwidth. It combines vector signal generator, vector signal analyzer and high-speed serial interface capabilities with FPGA-based real-time signal processing and control. The PXIe-5841 features the flexibility of a software defined radio architecture with RF instrument class performance. This VST delivers the fast measurement speed and small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments. The PXIe-5841 is available with an optional high-performance local oscillator module for improved phase noise, measurement time, and EVM performance. You can use the VST to test a variety of cellular and wireless standards such as Wi-Fi 6 and 5G NR. In addition, you can expand the small, two slot 2U PXI Express form factor to support multiple input, multiple output (MIMO) configurations.
-
product
RS-232
The RS-232 family includes transceivers with auto-power-down and standby functions, multi-channel interfaces and driver/receiver circuits. These devices have a 5 V supply or a 3 V to 5 V supply and are ESD protected enabling true RS-232 performance.
-
product
Proteus Arbitrary Waveform Transceivers
PXIe Modules
The PXIe module of the Proteus Arbitrary Waveform Transceiver (AWT) is based on the PXI Express industry standard. This platform enables up to 4 direct to RF generator output channels and 2 direct to RF digitizer input channels and occupies only 3 PXIe slots - Allowing scaling to 100's of channels.
-
product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
product
Wireless Receivers
Omega offers a full range of wireless reciever options. Form RS232-to-USB transceivers to long-range repeater/receiver systems, and connector/transmitter receivers.
-
product
Wireless Fiber Inspection Probe - WIS 300
Shanghai Fibretool Technology Co.,Ltd.
WIS 300 wireless fiber inspection scope is a WIFI/USB dual-use portable digital fiber inspector. With automated PASS/FAIL and fast images focus functionality, and easy pairing to Android™ and Apple© iOS devices, It can quickly check various patch cords and transceivers, display the fiber end face in PC/laptop/ OTDR/Smartphone etc..digital devices with the USB cable or WiFi connection. Under WiFi mode, it can automatically get the image checked and analyzed. Test results can do the pass/fail judges with IEC/IPC criteria. Fiber images and results can be saved on PC and mobile devices in jpg/pdf/excel format for file records. It’s super light and handy to take anywhere anytime for field tests, operation inspections, and lab research.
