Socket Testers
test access viability to electricity, gas or data.
-
Product
Test Sockets
BGA/LGA
-
There are a lot of options when it comes to bench test sockets. Save yourself and your lab time, money and frustration by working with Ardent for truly customized test socket solutions to meet your needs and do the job with high performance, reliability and quick turnaround that you need and deserve.
-
Product
TEST SOCKET
-
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
-
Product
Inverter Socket
Series 6621
-
Inverter Sockets. Inverted configuration allows the socket to be wave soldered on the component side of the PCB and the device socketed through a window on the solder side of the PCB. Available on .600 [15.24] centers. Consult factory for other sizes.
-
Product
Test Sockets
MEMS Device
-
Patented MEMS Sockets from Ardent Concepts use a unique scrubbing action contact set which is ideal for today’s sensitive MEMS devices, including accelerometers, gyroscopes, MEMS microphones and other specialized devices used in mobile electronics applications
-
Product
X4 With Micro-MaTch Socket
X4-xx-2/4
-
High performance, hall-sensed switch with Micro-MaTch socket up to 20 Ncm switching torque, up to 1 Mio switching cycles and optional push function
-
Product
Test Sockets
Non Standard
-
Chances are good Ardent can help you with that. We can adapt our technology to just about any package, device or module. Small volumes of custom sockets for higher bandwidth applications are a niche all in their own, and our engineering team has many years of experience designing custom sockets for all kinds of applications.
-
Product
Plug And Socket Torque Test Machine
-
Shenzhen Chuangxin Instruments Co., Ltd.
Plug Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. Plug Torque Tester is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.
-
Product
MultiSite Test sockets and Wafer Level
-
multi-site sockets include anything from strip test sockets to test sockets for wafer test to multi-position, singulated devices. The advantages of these sockets can be enormous as test time can be decreased by a factor of ten over conventional one up testing. In most cases, the throughput is only limited by tester capabilities and/or handling capacity.
-
Product
Socket Accessories (Thru-Hole Options)
-
The male pin adapter consists of standard high temperature FR4 with pressed in terminal pins and threaded inserts for mounting the socket. The top side of adapter has gold plated pads to receive socket interconnect and the bottom side has 0.006″ to 0.018″ diameter pin tails. These pins can be soldered to the plated thru holes in the target board. Then socket can be mounted to the threaded insert.
-
Product
Off-Set Kelvin Test Sockets
-
This is an innovative and robust contact technology for making Kelvin contact to 0.5mm pitch QFNs. The contact uses a tip that is angled to one side, matched to an orientation that's flat on the tip. Two such contacts placed in opposition will touch the pad within 0.125mm. And because the tip is offset, the probe diameter is a robust 0.39mm and the load board pad pitch remains 0.5mm.
-
Product
RF Device Test Socket
Coaxial Socket
-
With unparalleled technology, coaxial structure and high-precision machining equipment, LEENO can provide RF test socket with high bandwidth, impedance matching and high frequency up to 100Ghz.
-
Product
JEDEC TO Collet Socket
Series 514
-
TO Collet Sockets. Aries TO sockets feature molded chamfer lead-ins for easy device insertion. High stand-off design for heat dissipation and easy cleaning. External polarization for positive location.
-
Product
Custom Socket
-
Different structure:open top,clamshell or handlerOne type: design socket according to customer's PCB.The other type : customer layout PCB according to socket datasheet.Please tell device voltage,current,frequency and temperature and other requirements.
-
Product
Open-Frame Collet Socket with Wire Wrap Pins
Series 508
-
Open Frame Collet Sockets with Wire Wrap Pins. Features: Open frame allows for more efficient utilization of board space and better cooling. 2 and 3 level wire wrap pins available. Compatible with automatic insertion equipment. Side-to-side and end-to-end stackable.
-
Product
DIP-to-JEDEC TO Adaptor Socket
1109522 & 1109523
-
DIP to TO Adapter Sockets. 8 pin DIP IC socket on the top and a circular, 8 pin TO can male pin footprint on the bottom. ICs now available only in 8 pin DIPs can be readily mounted on boards having TO thru-hole footprints without having to redesign the board.
-
Product
Test & Burn-In Socket for Devices up to 13mm Square
CSP/MicroBGA
-
Test & Burn-In Socket. Socket is easily mounted and removed to & from the BIB due to solderless pressure mount compression spring probes which, are accurately located by two molded plastic alignment pins and mounted with four stainless steel screws. Standard molded socket format can accommodate any device package of 13mm or smaller, by using machined (for small quantities) or custom molded (for large quantities) pressure pads and interposers.
-
Product
Hand Socket Lid
-
Hand socket lid is normally used to run evaluation tests on semiconductor devices prior to High Volume Manufacturing mode. It can also be used as a trouble shooting tool at bench test.
-
Product
Socket Wrench Torque Sensor Reaction Type
SWS SERIES
-
Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. alibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.
-
Product
Test Sockets
-
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
Product
SLT Socket
-
Mobile Phone, Tablet, TV Board, Set-top box etc.LEENO can provide a System Level Test solution on various types of packages.
-
Product
Probe Tip Ground Lead with 0.8 mm Socket
PK007-024
-
Probe Tip Ground Lead with 0.8 mm Socket.
-
Product
Multi Socket Programmers
-
Gang programmers are based around the universal programmers but offer multiple sockets allowing 4 or more devices to be programmed at the same time giving a greater throughput where a large number of devices require programming. Mass production environments churning out tens of thousands of chips a week are where these programmers are typically found.
-
Product
Pin-Line™ Collet Socket with Solder Tail Pins
Series 0513
-
Pin-Line Collet Sockets with Solder Tail Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with solder tail or wire wrap pins. Consult Data Sheet No. 12014 for wire wrap pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
X4 With Micro-MaTch Socket Or FFC Connector
X4-Overview
-
High performance, hall-sensed switch for various coding, with mechanical and electrical interfaces, up to 20 Ncm switching torque and optional push function
-
Product
Ethernet Tester
-
Shanghai Grandway Telecom Tech. Co., Ltd
Datacom tester including 2M Transmission Analyzer, TV Signal Tester, Cable & Antenna Analyzer, 1G(1000M) Ethernet Tester, 10G Ethernet Tester, etc.
-
Product
Servo Tester
105
-
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
Product
Surge Tester
-
They are designed to detect quality defects in the insulation between winding turns, ensuring the reliability and performance of electrical components.
-
Product
EOS Tester
KT-200SG
-
This test instrument stands for the EMI(Electro Magnetic Immunity) ability test to the electric devices, electronic circuit boards & electric equipments. Recently this instrument is widly used in many companies in Korea & other countries to test the immunity to thier products-power supply, drive PCBs, communication systems, LCD display panels whether they are safe or not against the impulse & noise.All for the purpose, of this object, it generates 4 ~ 5 kinds of different impulse test waveforms.Output test voltage level : 5 ~ 200 V ImpulseOutput voltage polarity : Positive, NegativeType of waveforms
-
Product
Multifunctional Testers
-
Electrical installation safety is nowadays more important than ever with the proliferation of increasingly complex domestic electronic appliances people install in their homes that require reliable power supply lest they become damaged and pose a fire and electrocution risk. Effects of unreliable and even dangerous electrical installations are even more acutely felt in industrial environments where they translate into production losses.
