Radar Detectors
Monitor for rf and laser waves.
-
Product
RF Detectors
-
RF detectors from Fairview Microwave are available with N Type or SMA connector series inputs and BNC or SMA connectors for outputs. Fairview RF detectors are zero bias Schottky diode and have negative video out. These zero bias Schottky diode detectors for RF have a minimum frequency between 10 MHz and 2 GHz and maximum frequency range between 2 GHz and 26.5 GHz.
-
Product
LM-79 Moving Detector Goniophotometer
LSG-5000
-
Moving Detector Goniophotometer completely meets LM-79 Clause 9.3.1 and EN13032-1 clause 6.1.1.3 goniophotometer type 4 requirements. The LSG-5000 is an automatic light distribution intensity 3D curve testing system for measuring light. The measuring distance is from 5m to 30m. It can measure all types of lighting sources, LED or HID luminaires such as indoor and outdoor luminaires, roadway luminaires, street lamps, flood lights and other kinds of luminaires.
-
Product
Gas Leak Detector
-
Shanghai Yiya Electronic Instrument Co., Ltd.
High-frequency generator used for detecting leaks in a pumping system.
-
Product
SF6 Gas Purity Detector
JH4000CD-1
-
Xiamen Jiahua Electrical Technology Co.,Ltd
Purity of SF6 gas is not only a major item for gas quality acceptance and evaluation of equipment installation and maintenance process, but also a reliable accordance for internal troubleshooting. According to gas purity changes, it can be judged whether the equipment has any serious fault.
-
Product
Metal Detector
Profile Advantage
-
Maximum Sensitivity and Performance; Multi-Simultaneous Frequency & Product Signal Suppression technology deliver the ultimate detection sensitivity with zero false triggering. Simple to Use and Robust Detector Design. Superior performance on wet and conductive products. Product signal suppression overcomes product effect to detect more metal contamination in challenging applications irrespective of packaging type.
-
Product
Plugged Chute Detector
-
The Drexelbrook Plugged Chute Detector reliably detects the presence or absence of material flowing through chutes. If process material stops flowing due to a plugged condition, the flush mounted capacitance sensing element will alarm, allowing further action to occur (alerting an operator, shutting down a conveyor belt, etc.).
-
Product
VME Master - DAQ and Detector Interface
VX1394
-
The VX1394 board features a radiation hard 4.8 Gbps SERDES ASIC, which, in connection to a rad-hard optical transceiver implements a newer generation optical links for many detector readout systems. The ASIC performs data transmission, trigger distribution and clock forwarding towards the front-end electronics in the crate.
-
Product
CO Detector Testing
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Photoacoustic Detector
PA301
-
improves laboratory productivity and safety by enabling extremely versatile and rapid analysis of solid, semi-solid, and liquid samples in any form without sample preparation.
-
Product
Ultrasonic Gas Leak Detector
Observer® i
-
Instantly detect pressurized gas leaks with this high-precision, omni-direction acoustic detector utilizing Gassonic ultrasonic technology. Works even when traditional methods of gas detection are unsuitable or dependent on ventilation.
-
Product
3D Ground Penetrating Radar data processing & Interpretation software
Condor
-
Condor is modern processing, visualisation and interpretation software for the efficient management of Raptor 3D GPR array data.Boost performance and improve workflows.- Efficient sub-surface imaging- Effective workflows- Simple and intuitive- Dedicated to processing Raptor data- Modern Windows software (64-bit)
-
Product
Superior Handheld Partial Discharge Detector
PDStar
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is proud to present one of our latest innovations, the PDStar. It integrates On-Line Partial Discharge (OLPD) testing and Infrared testing for MV and HV equipment, which combines UHF, AE, Ultrasonic, HFCT, TEV, and Infrared testing technologies. It is applicable for online PD testing, as well as abnormal heating and defect detection on all types of substation equipment. PD amplitude, PRPD, PRPS, and infrared spectrums provide critical data for determining the operational condition of electric power equipment. It connects to the PMDTCloud via Wi-Fi/3G/4G to upload test data, download test tasks, and receive diagnostic results in real time. Another uniquely advanced feature of the PDStar is that it integrates with a 100 MSPS (Mega-Samples per Second) HFCT signal processor, which greatly improves the performance for power cable OLPD testing.
-
Product
Servicing and Testing of Search and Rescue Radar Transponder
SART
-
The Search and Rescue Radar Transponder as a part of GMDSS is a subject to annual test during radio survey. The annual testing of SART is recommended due to SOLAS regulation IV/15.8.The purpose of an annual testing is to determine that SART is operational as defined in appropriate performance standards for Survival Craft Radar Transponders for use in Search and Rescue Operations, IMO Resolution A.802 (19).Also Marine Orders require that a radar transponder must be inspected, tested and have its batteries replaced at intervals specified by its manufacturer.
-
Product
Tunable Detectors
-
Due to their spectral properties and robustness, pyroelectric detectors have proven themselves for many years in numerous applications in gas analysis, flame detection and spectroscopy. They enable the tuning of the optical filter over a defined spectral range by simply adjusting the control voltage. Instead of mounting filters to inspect specific areas of interest as is conventionally common, the detector with tunable Fabry-Pérot filters (FPF) can be used to monitor a broad spectral region continuously.
-
Product
Ultrasonic Flaw Detector
ECHO
-
The ECHO scanning acoustic microscope is a nondestructive ultrasonic flaw detector designed to simplify testing, increase yield and maximize productivity in the lab or on the production floor.
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Contact Voltage Detectors
-
Shanghai Beha Electronics Co., Ltd.
The detector detects a high and extra high voltage in AC lines. An elongate insulation rod permits checking of high voltage circuits at safe distance for voltage.
-
Product
HPx-200 PCI Radar Input Card
-
The HPx-200 is a flexible, cost-effective PCI primary radar acquisition card that captures and processes one or two analogue or digital radar video signals from a single radar. The card is fully supported by SPx software, allowing modern radar processing to be added into legacy systems.
-
Product
Point IR Gas Detector
IR400
-
The IR400 Infrared (IR) Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication.
-
Product
Phantom Metal Detector
-
Available in aluminum or stainless steel with a wide variety of aperture sizes, Phantom Metal Detectors are built rugged to withstand the harshest applications. For heightened stability and performance in wet product applications, the IP69K certified BSH Extra Rugged Casing is utilized. An epoxy chute provides a complete waterproof seal on IP69K rated units.
-
Product
Radar Simulation Software
Pulse Sequencer
-
R&S®Pulse Sequencer software together with a vector signal generator from Rohde & Schwarz or just as software provides a compelling radar signal generation solution to engineers and technicians responsible for testing radar receivers. The solution is in line with the trend of testing more in the lab rather than expensive field testing. Co-engineered with the industry, the solution supports all relevant modern radar scenario test cases and can account for real-world environments. It uses commercially available R&S®Pulse Sequencer PC software and off-the-shelf Rohde & Schwarz vector signal generators.
-
Product
Pulse Holiday Detector
NOVOTEST SPARK-1
-
Pulse Holiday Detector NOVOTEST SPARK-1 designed to detect pits, flaws, and holes in different non-metallic insulation coatings (such as polymers, epoxy, bitumen, etc.) and is mostly used for oil and gas metal pipelines and other objects. The device can be used while the pipeline construction, operation or service. Tested coating thickness is up to 12 mm. Such tests are needed to evaluate the oil and gas pipelines corrosion protection reliability.
-
-
Product
Metal Detector
Safeline Profile Advantage
-
For challenging inspection applications where a product is wet, hot, chilled or cooling Profile Advantage technology provides the ultimate in metal contaminant detection capability. All metal contamination including ferrous, non-ferrous and even the most difficult to detect non-magnetic stainless steels are readily detected enabling them to be removed effectively from the manufacturing process.
-
Product
Ultrasonic Corona & Arcing Detector
ULD-40™
-
The ULD-40™ is an ultrasonic detector designed for corona effect and arcing detection for predictive maintenance in electric utilities. Available with a variety of accessories, this instrument is a cost-effective must for any prevention plan.
-
Product
Non-Contact Voltage Detector
273 HP
-
Standard Electric Works Co., Ltd
2 ranges for selection : LOW 50V~1.5kV, HIGH 1.5kV~132kV. There is no power consumption in off mode : 0uA. Nice mechanical slide switch for function selection : HIGH / OFF / LOW. The power consumption in low voltage detection mode : Less than 20mA. The power consumption in high voltage detection mode : Less than 20mA. Bright LED and audible alarm sound when voltage is present. Lightweight, robust and compact. Efficient and easy to use. Users have to use the Hot Stick when test high voltages between 1.5kV~132kV. SEW provides nice optional accessories of Hot Sticks HS-175 and HS-120 for high voltage detection. Optional accessories : HS-175 Telescopic hot stick (triangle-type) and HS-120 Hot stick.
-
Product
Gas Leakage Detector
-
*Sense leakage of combustible gases such as butane, propane, acetylene and - methane (natural gas)
-
Product
Ultrasonic Flaw Detector
MFD620C
-
The MFD620C is an advanced digital ultrasonic flaw detector featuring a multi-color TFT LCD and a host of new features to meet challenging inspection requirements. It combines powerful flaw detection and measurement capabilities, extensive data storage, and the ability to transfer detailed inspection data to the PC via its high-speed USB port.
-
Product
Photo Detectors
-
Our photo detectors are offered for both power or energy measurements. Measure as low as a few femtojoules in energy or a few picowatts in power, thanks to our highly sensitive sensors and performant electronics.
-
Product
Flame Ionization Detector
-
A flame ionization detector converts a hydrocarbon gas concentration into an electrical signal. The flame is hydrogen fueled and burns in hydrocarbon free combustion air. Either side of the flame are two electrodes between which an electric field is generated by means of a polarization voltage. The sample is pre-mixed with the fuel gas and heated in the flame to a temperature at which the hydrocarbon molecules ‘crack’ and CH fragments appear. These CH fragments are oxidated by the oxygen in the combustion air resulting in the formation of CHO+ ions. The ion current then passes to the electrodes and the resulting current measured is proportional to the quantity of C atoms derived from organic compounds.The Thermo-FID features two separate microprocessor controlled pressure compensations to avoid any influence from environmental or sample conditions. In addition, the complete Thermo-FID range of analyzers are equipped with a flame trap that is used as a heated sample inlet filter. The measurement chamber and all material in contact with the sample gas are heated between 120°C and 200°C to avoid condensation.
