AC Current Clamps
wrap around conductors to measure current.
-
Product
Clamp Meter
-
Shenzhen Graigar Technology Co.,Ltd.
A clamp meter is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
Product
AC Load Bank
-
PC software controls offer advanced load profile solutions and model options range from small, portable, low-power units, to high-power indoor or outdoor permanent load solutions.
-
-
-
Product
Current Transformers
-
A range of ring type current transformers suitable for primary currents from 1A-5000A with 1A or 5A secondaries. This standard range of measuring and protective current transformers is available as resin coated or tape wrapped.
-
Product
C/I Clamp Meters
CLAMPMETER,OPEN JAW (CSJ-100)
-
*AC amperage, AC/DC voltage measurement*Open jaw design eases AC current measurement*Slim profile with build-inprobe storage on back*Measures resistance up to 20MΩ*Audible continuity and diode test*Bright LED and audible alarm for non-contact voltage detection*Auto power off for longer battery life*Data hold to capture measurements*2000 count LCD*Accessories included: (2)1.5V AAA batteries, test leads and carrying case*Lifetime Limited Warranty
-
Product
Leakage Current Testers
-
For general-use electrical devices Built-in non-medical use networks For rated currents of up to 20A For automatic testing on production lines, etc.
-
Product
Self Testing Clamps with Visual Indicaiton
Bond-Rite REMOTE EP
-
The advent of the Bond-Rite REMOTE has allowed the further development of a mains Externally Powered (EP) version. This is ideal for applications where the clamp will be attached to plant / containers for prolonged periods of time, or where a monitoring system without interlocks is required (eg. for use during manual product transfer).
-
Product
Integrated Current Sensors
GO series
-
*Standard package and small footprint*Cost effective*A perfect compromise for small drives, robots, solar inverters, e-bikes etc.
-
Product
AC Hipot Tester
-
KV Hipot Power Test Equipment Co.,Ltd
The Hipot tester is a nondestructive test which is a effective way to determine the insulation strength for electric equipment.
-
Product
Single-point Current Meter
-
The SEAGUARD® is the core module used in small and medium sized underwater observatories. Whether used as a multipurpose instrument, or as a hub for strings in the water column, the SeaGuard manages connected sensors and the real-time communication of data and meta-data to shore. In autonomous configurations, long battery life is achieved with aggressive power routines keeping the full system at the lowest power levels possible.
-
Product
AC Power Source
-
NF’s AC power sources are designed and built to deliver high-quality, high–precision AC power. In recent years, NF’s products have been used for power-supply environment testing such as immunity testing of electronic components.
-
Product
AC Power Supplies
-
a series of multifunctional switching AC power supplies that combines accurate, high power output .
-
Product
Electromagnetic Ammeters And Voltmeters Fb-1, AC Electric Current, AC Voltage
-
ELECTROMAGNETIC DEVICES FOR MEASUREMENT OF ACTIVE VOLTAGE AND ACTIVE CURRENT.
-
Product
Current Transformers Test Set
-
Supreme Instrument Laboratories
The basic unit is sensitive magnetic comparator and also it incorporates electronic null detector to facilitate the balance. The reference Current 5A. or IA. obtained from Standard Current Transformer and in comparison to that the vector length and phase displacement is measured. The ratio error in percentage and phase displacement in minutes are directly compared and indicated on dials.
-
Product
Current Transformer
LTTJ
-
Love Controls LTTJ Series Current Transformers allow easy monitoring of the current flowing to your load. This easy to use device provides a 0 to 10 VDC signal into both low and high impedance circuits, and is easily scalable to your needs
-
Product
AC Voltage Test Systems
-
HIGHVOLT Prüftechnik Dresden GmbH
AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
Product
Eddy Current Flaw Detector
US-525M
-
United Western Technologies Corp
The US-525M multi-channel eddy current testing instrument is a rugged industrial rack-mounted instrument offering multi-channel testing, integral digital strip chart, as well as Ethernet control and data transfer to meet your in process testing requirements. This instrument offers up to eight channels, with a frequency range of 20 Hz to 10 Mz, a high signal-to-noise ratio, a bright 12-inch diagonal color LCD flat-panel screen, and data storage of 32 Gig. It offers input/output (I/O) capability, USB and Ethernet connectivity, as well as three discrete alarm gates with independent outputs per channel. for your on-line bar, tube, wire and specialty component testing needs.
-
Product
Current Probe
DCP-BTA
-
Vernier Software & Technology, LLC
The Current Probe measures DC and low-frequency AC currents up to 600 mA. Use Current Probes in combination with Differential Voltage Probes to investigate Ohm's Law and explore series and parallel circuits. The 0.1 shunt resistor minimizes changes to your circuit. If currents will exceed 1 A, use the High Current Sensor.
-
Product
Current Feedback Op Amplifiers
-
Analog Devices high speed (> 50 MHz) current feedback op amps enable you to operate at higher speeds. Current feedback op amps traditionally have wider bandwidths and higher slew rates than voltage feedback amplifiers and do not feature a gain bandwidth restriction associated with voltage feedback op amps.
-
-
Product
AC/DC Clamp Meter
ST-3602
-
Standard Electric Works Co., Ltd
● 3½ digit LCD with maximum reading of 1999.● Over range indication : "1" is displayed on highest digit.● Low battery indication: "B" sign appears on the display.● Response time: approx. 1 second.● Data hold: for all ranges
-
Product
DC Precision Current Sources
-
DC Precision Current Sources provides precise and very stable output currents from 3 A to 10,000 A. The 6623A-PCS Series provides the best uncertainties of any DC high current sources (i.e. < 5 ppm of precision and stability at 1000A). In addition this Series is modular and initial output currents can be expanded at any time.
-
Product
Magnetic & Current Sensors
-
From the International Space Station to a simple electronic compass, we can provide a solution to meet your magnetic semiconductor needs. The F.W. Bell® product line was founded in 1944. Since then we have been a pioneer in developing instrumentation to measure electric current and magnetic fields.
-
Product
Source Systems AC
-
The power sources of MTS-series based on digital amplifier modules combined with frequency generator and reference device are the MTS source system. Single-phase systems (MTS1xx) or three-phase systems (MTS3xx) from 1 to more than 40 test positions are available.
-
Product
AC Ionisation
AC Short Range
-
Fraser Anti-Static Techniques Ltd
AC static eliminators for manufacturers.
-
Product
Current Transformer Analyzer/Tester
GF1061
-
Beijing GFUVE Electronics Co.,Ltd.
Portable CT PT analyzer is mainly used for field or lab testing, it can finish the measurements (M) and protection (P) class CT, PT and TYP class CT. Adopt 7 inch touch TFT LCD, self-equipped mini type printer supporting field printing; supporting to use USB flash disk to download data or RS232 port to PC control. This model GF1061 CT PT analyzer is the most complete and easy-to-use testing system for protection and metering CTs according to IEEE C57.13 and IEC60044 & IEC61869 standards.
-
Product
AC High Voltage Tester
VHT
-
VEER make High Voltage Tester VHT is specially designed to test Dielectric Strength of Device under Test as per applicable standards. High Voltage test is required to determine whether test object has proper insulation or not. High Voltage test is carried out as Routine Test Each device is subjected to test at high voltage of 1 kV + 2 x (working Voltage)If Insulation is weak then device will consume more power because of leakage current which causes more heat. Heat will reduce the reliability and overall life of device under test It is also responsible for high risk of electric shock. So, High voltage test is necessary for all electrical equipments.
-
Product
Earth Resistance Clamp Meters
-
Precision Mastech Enterprises Co.
Specialized, non-intrusive electrical testing tools designed to measure grounding system resistance without disconnecting the ground rod or using auxiliary electrodes.
-
Product
AC Insulation Testing
-
AC insulation tests are a popular response to the increasingly demanding industrial, power and domestic marketplaces. Insulation materials have had to become more efficient to keep up with demand; more efficient equipment requires less insulation material to meet the minimum acceptable value of insulation resistance. In turn, cables have become smaller and lighter. However, under certain higher stress testing conditions such as DC testing, cables like Crossed Linked Polyethylene (XLPE) can quickly degrade.
