Crimp
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, 50µ” Au, Crimp
610138116
*Please note: The difference between this p/n and 610138216 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138112. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCuContact Plating 50µ" Au over 100µ" NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force(lbs) 0.24
-
product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 16A, 2m
A020GMR-C-1B200
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Ferrules, 0.5m
40-972-009-0.5m-FU
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 20 GHzVSWR 1.15 + .01 (f) GHz w/ RG142 (8 GHz)1.15 + .01 (f) GHz w/ SF142 (20 GHz)Insertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG 223 Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
20-Pin GMCT Cable, Female to Unterminated, Tinned Ends, 16A, 0.5m
A020GFR-T-1B050
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 1m, HV
40-972-009-1m-FU-HV
A range of 9 Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 2m
40-972-025-2m-MU
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Tool, Locator, Micro Coax, Receiver
910101135
Included with Crimp tool kit p/n 910101132 and kit p/n 910101131.
-
product
Tool, Crimp, Mini Coax, RG316 and RG178
910101115
Used for VPC mini coax contacts. Includes locator and die set.
-
product
Signal/ Micro Power/Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Positions, for crimp contacts
510160107
Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
product
Micro and Milliohmmeter
AD-7110
The instrument AD-7110 is designed to measure, with high accuracy, resistance conductive elements of power devices: motor windings, transformer windings, conductor rails, inspecting the electrical conductivity of screw connections, crimp, welded state of the contacts of switches and relays current up to 100 A .
-
product
Cable Assembly, 26-Pin D-Type, Female to Unterminated With Ferrules, 2m
40-972-026-2m-FU
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
HeavyPower & EasyPower
Transformer Series
Transformer Series offers a customer configurable architecture, with just a few piece parts to create several types of connectors as a platform solution. No special tools are needed except crimping tools, resulting in a reduced stock and kitting/logistic management. The series offers a high reliability due to the Tortac® contact and provides up to 500 mating cycles and high current rating up to 300A/500A.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, Crimp, 30µ" Au
610138216
*Please note: The difference between this p/n and 610138116 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138109. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCuContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force(lbs) 0.24
-
product
Tool, Crimp, QuadraPaddle, Receiver
910101125
Crimp Tool Part # 910 101 125 is used to crimp receiver QuadraPaddle contacts.
-
product
Tool, Locator, Thermocouple, ITA
910104135
Used with Crimp Tool p/n # 910101102 to crimp thermocouple ITA contacts.
-
product
20-Pin Scorpion Female Connector, 30A, With Backshell
C020AFR-2CP-3A
This is a female 20-pin Scorpion Connector with crimp pins suitable for 10AWG cable. It is supplied with a rear cable entry backshell that includes screwlocks and cable clamp. The connector is keyed to position 2 and it has a maximum current handling of 30A and is suited for direct connection to Pickering Interfaces products.
-
product
4-Wire Resistance Measurement | Continuity & HiPot Cable & Wire Harness Testers
An add-on option for the CableEye HVX high voltage cable tester series that permits expanded testing for contact and wire resistance as low as 1 mΩ. After checking for opens, shorts, miswires, and resistance limits, the 4-wire Kelvin measurement applies a user-selectable test current from 10 mA to 1 A to determine connection resistance within 1 mΩ. The resistance profile of a model cable may be stored and used as a basis of comparison during later testing to reveal cold solder joints, faulty crimps, recessed pins, pin contact contamination, improper wire gauge, and stress-extruded wire.This option may be purchased with any new HVX tester, or added as an upgrade to any of your existing HVX testers.
-
product
50/75 Ohm Micro Coax Contacts
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
product
Cable Assembly, 26-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-026-0.5m-MU
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Temperature Wire And Cable Tools
Omega's specialized tools for stripping, welding and crimping wire and cables help you complete your project safely and on time.
-
product
Mating Coax Connector and 20 Coax Pins Crimped (both ends) to 5' wires
GX96405-60
Mating coax connector and 20 coax pins crimped (both ends) to 5 ft wires
-
product
Cable Assembly, 26-Pin D-Type, Female to Unterminated With Ferrules, 0.5m
40-972-026-0.5m-FU
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Connector, Cable Mount, 25 Pin 1.27mm Pitch Micro-D, Female, Crimp Pin
C025CFR-1CP-0A
This 25 pin micro-D connector is designed to allow users to directly terminate with crimped connections and is suitable for 26 AWG copper wire. Screwlocks are provided to secure the connector to its associated product. This connector is suitable for high density applications including connection to Pickering's LXI DIO/Trigger port.
-
product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 16A, 2m
40-972C-020-2m-FU
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Wire Crimp Testers
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
