Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Tool, Crimp Die, Micro Coax, f/ RG 316 and RG 179 wire
910101133
Included in Tool kit 910101132.
-
product
Wire Crimp Pull Sensor
Model MR06-200
The MR06-200 wire crimp pull sensor is a hand-operated solution for measuring wire crimp pull-off forces. The ergonomic handles and convenient tensioning mechanism make field measurements a breeze for applications up to 200 lbF (1,000 N). Squeeze the handles together to increase tension on the sample until a break occurs. The peak force is recorded by a Mark-10 indicator. A rotating turret with slots of multiple sizes accommodates a wide range of wire diameters, up to 0.25 in. (6.4 mm).
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Signal , Module, Receiver, QuadraPaddle, iCon Series, 160 Position, for crimp contacts
510160101
Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
product
160-Pin DIN41612 Connector, Crimp Pin, Female, 90º
40-960-160-FT
Suitable for users to create their own cable assemblies where a 90 degree down cable exit would be preferred. If the user requires the connector to have a second fixing then it can be fitted with an additional screwlock assembly 40-969-101 where applications permit.
-
-
product
Tool, Crimp, QuadraPaddle, Receiver
910101125
Crimp Tool Part # 910 101 125 is used to crimp receiver QuadraPaddle contacts.
-
product
Bench-Top Wire Crimp Pull-Force Tester
PT-1500
PT-1500 Bench-Top Wire Crimp Pull-Force Tester, Manual Lever-operated for 5.84mm 8-30 AWG
-
product
20-Pin Scorpion Female Connector, 30A, With Backshell
C020AFR-2CP-3A
This is a female 20-pin Scorpion Connector with crimp pins suitable for 10AWG cable. It is supplied with a rear cable entry backshell that includes screwlocks and cable clamp. The connector is keyed to position 2 and it has a maximum current handling of 30A and is suited for direct connection to Pickering Interfaces products.
-
product
Tool, Crimp, Mini Coax, ITA, 24-26 AWG Wire
910101118
Used to crimp Mini Coax ITA contacts to 24-26 AWG wire. Locator required.
-
product
50/75 Ohm Micro Coax Contacts
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
product
Solar PV Test Equipment
Di-log offer a comprehensive range of Solar PV test equipment and tools to service the renewable industry. The range offers irradiance meters, DC current clamp , meters, crimp tools, roof surveying and protective gloves.
-
product
Pin Insertion Tool For Scorpion Connectors With Crimp Pins
C020AFR-2CP-2A-I
Extractor tool for crimp pins fitted into a Scorpion connector housing.
-
product
Thermocouple, Contact, ITA, Alumel, Type K (°C)
610113134
Primary mating contact 610113132.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Thermocouple, Contact, Receiver, Alumel, Type K (°C)
610113132
Primary mating contact 610113134.Thermocouple contacts are manufactured from chromel or alumel alloys and color-coded for easy identification. Contacts are crimp terminated and easily inserted into the connector module. They can be readily removed from the connector module using a special removal tool.
-
product
Signal/ Micro Power/Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Positions, for crimp contacts
510160107
Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
product
Tool, Kit, High Power, Receiver and ITA, Crimp
910102116
This crimp tool kit contains a pneumatic crimp tool, plus locator and die set specific to high power contacts.
-
product
Tool, Kit, 75 Ohm Coax, ITA, Cable Install
910102107
Consists of 2 tools for installing cabling into the contact. Crimp Tool and Locator for center contact and Hex Crimp Tool for outer shield (p/n# 910104139).
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, Crimp, 30µ" Au
610138216
*Please note: The difference between this p/n and 610138116 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138109. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCuContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force(lbs) 0.24
-
product
Tool, Kit, High Power, Receiver and ITA, Crimp
910102117
This tool crimp kit contains the specific locator and die set for 2 AWG High Power contacts.
-
product
Wire Crimp Pull Tester (Manual)
WT3-201
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
product
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp
510143002
Signal, Module Insert, Receiver, i2 MX, 84 Position, QuadraPaddle, Crimp.
-
product
Tool, Locator, Micro Coax, Receiver
910101135
Included with Crimp tool kit p/n 910101132 and kit p/n 910101131.
-
product
Wire Crimp Testers
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
product
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator
910104126
Tool, Crimp Die, Mini Coax, RG316 and RG178, with Locator.
-
product
Assembly & Test Services
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
product
ITA, i2 MX, 2 QP Modules, Crimp, EMI Backshell (includes front protective cover)
410130202
ITA, i2 MX, 2 QP Modules, Crimp, EMI Backshell (includes front protective cover).
-
product
Alumel, Type K (°C) Contacts
Thermocouple contacts are manufactured from chromel or alumel alloys and are color-coded for easy identification. They are crimp terminated and easily inserted into connector modules and readily removed using a special removal tool.
-
product
160-Pin DIN41612 Connector, Crimp Pin, Female
40-960-160-F
Suitable for users to create their own cable assemblies, can be supplied with or without the backshell. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the connector can be fitted with an optional screwlock assembly.
-
product
Signal, Module, ITA, i2 MX, 84 position, QuadraPaddle, Crimp
510144002
Signal, Module, ITA, i2 MX, 84 position, QuadraPaddle, Crimp
