Flow Testers
-
product
Automotive Radar Testers
Rohde & Schwarz provides automotive manufacturers, components suppliers and test houses with innovative, cutting-edge solutions which bring realistic test scenarios from the road to the lab and production line.Our range of solutions include a signal generator-based target simulator, a radome & bumper tester and an anechoic automotive radar test chamber allowing for over-the-air (OTA) testing. These solutions are at the heart of the development of advanced driver assistance systems (ADAS) with its safety-critical features such as emergency braking. Using T&M solutions by Rohde & Schwarz enables a thorough testing of chipsets, sensors and modules at each phase from development and conformance to production.
-
product
Solar Cell Testers
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
product
Insulation Resistance Tester
HT2671 / 761
Wuhan Huatian Electric Power Automation Co., Ltd.
Mainly used to check the insulation resistance of electrical equipment or electrical lines to ground and phase to ensure the normal operation of these equipment.
-
product
Stopped-flow/quench Flow
QFM-4000.
A unique design enables the QFM-4000 to trap and identify reaction intermediates. The device is also commonly used for analysing enzymatic reactionq, DNA cleavage or single turnover reactions.
-
-
product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
product
Diode Tester
FEC200E
Frothingham Electronics Corporation
The FEC200E is an automatic computer- controlled diode and rectifier tester. It is controlled by a standard PC-compatible computer running FreeDOS.
-
product
Capacitance and Inductance Tester
JY6700
Capacitance measurementsInstrument can test take a single capacitor without stitches in test group capacitance to bring convenience to test. It will show test results of capacitance while show test
-
product
High Speed & Precision Pressure Insensitive Mass Flow Module
D700MG
Critical semiconductor manufacturing processes continuously desire precision gas flow control devices that enable both future innovation, and lab to fab transition of leading edge memory and logic device. HORIBA's propose the new pressure based MFC D700MG, the upper compatible model of the D500MG to support customer’s challenges.
-
product
Flow Sensor For Compressed Air (FLUEREX With Integrated Display)
PF/PFU
This is a flow sensor for compressed air for medium and large flow rates, which is useful for grasping the current state of energy consumption and confirming the effect.
-
product
Personal SerDes Testers
C Series
Everything you need to develop and verify your high-speed digital algorithms is contained in these ultra-portable test instruments. They will forever change the way you think about developing and verifying Gbps digital and mixed-signal algorithms, and they will allow you to measure signals in ways that were not possible in the past. Each personalized SerDes tester is equivalent to multiple hardware platforms, containing everything that you need to make high-performance measurements like bit error rate testing, signal generation, and signal measurement.
-
product
Insulation Tester
AD-2050
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation. 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
product
Demattia Flex Tester
UI-FT33
Demattia Flex Tester & Demattia Flex-Cracking Tester is used to test rubber crack growth under repeated bending or flexing. Unuo manufactures demattia flexing fatigue tester which meets test methods of ASTM-D813, GB/T 13934, HG 2873, ISO 132:1999(E), BS 903-A10 and etc.
-
product
LPG Mass Flow Rate Detection System
This is a massflow rate measurement system that can measure the massflow rate of LPG with high accuracy using the Coriolis method massflow meter.LPG is a fuel that easily vaporizes, and it is not difficult to measure the correct flow rate in a gas-liquid mixed state.
-
product
Cable Fault Testers
*Compact and lightweight solution for underground cable testing*DC Hi-Pot test of de-energized, shielded underground primary cable*No external power required - self-contained 8kVDC voltage source*Can be used up to a distance of 1500 ft (457m)*Clear and simple test results - analog bar graph and indication of good or faulted cable*Safety feature - measures AC voltage before converting to a DC voltage tester*Lightweight, single hot stick operation for testing cable
-
product
Incline Shock Tester
HIACC Engineering & Services Pvt. Ltd.
Inline shock test system simulates a real shock environment to estimate the impact resistance or damage level of a product. The simulated environment replicates shocks produced during product handling, stacking shelves, loading/unloading and transportations. The incline shock test system is widely used in the packaging industry, scientific research institutions and transportation industry.
-
product
Outdoor Exposure Tester
OET
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
product
Digital Insulation Testers
Cut unscheduled downtime and reduce shock hazards by testing wires, cables, transformers or entire electrical systems.
-
product
Semiconductor Device Testers
are particularly suitable for certain semiconductor test requirements, but other models may also be of interest. Our knowledgeable application engineers can guide you to the most suitable model.
-
product
Vibration Testers
Analyzes vibration patterns within mechanical systems or individual components and structures to identify defects and evaluate the test object's overall condition.
-
product
Karman Vortex Flow Sensor For Water Flurex
WFK2
Karman vortex flow sensor for water that covers 0.4 to 250 L/min. Various output switching settings are possible and IO-Link communication is also supported.Equipped with a water temperature measurement function as standard, it supports fluid temperatures up to 95 °C...
-
product
Radome Tester
QAR50
The R&S®QAR50 is the ideal tool for accurately testing the quality of automotive radomes and bumpers in the automotive radar frequency range at the end-of-line (EOL). It features sufficient space to easily accommodate bulky bumpers combined with spatially resolved measurements to evaluate the homogeneity of design emblems.
-
product
Relay Tester with Timer/Counter
15967
The new Ultra-Tech Model 15967 Relay Tester with Timer/Counter will consistently test various relays that include: Timers, Coders, slow Release and Slow Acting. As well as performing the standard tests, th9s new tester will display the Code Rate and Duty Cycle percentage while you are testing Coding Relays.
-
product
ELT Testers
BT200 Series
Building on the features of the industry standard BT100, the BT200 offers improved measurement capabilities and in a fully integrated and ruggedized device. The BT200 meets and exceeds the measurement requirements for EPIRBs (IMO MSC/Circ.1039 and 1040) and for ELTs in the USA (FAA Part 91.207), in Canada (CAR 571 Appendix G), and Europe (CAA/EuroCAE requirements). These Beacon Testers in fact form a cost effective solution by eliminating the need for other costly test equipment. Don’t risk incomplete testing of your beacons – use the BT200 to test them thoroughly. In compliance with your Quality Assurance requirements, detailed calibration data is included with each Certificate of Calibration.
-
product
Disintegration Testers
Disintegration Testers have wide application in Pharmaceutical Industry, for disintegration of tablet and capsule (solids) in prescriptive conditions like tablet, capsule, and ointment, etc. across manufacturing plants, research centers.
-
product
Surge Testers
MTC 2
Advanced automatic high precision electrical winding testers for testing products like alternators, stators, transformers, armatures and motors. Available as static or portable units from 6-50 kV.
-
product
USB SOCKET TESTER
MDPPTSTUSB
*Provides the user with a simple way to test a USB socket on a vehicle*Mini probe will light up when 4.4V - 5.25V is detected
-
product
Cable Tester
CT-3
Monacor International GmbH & Co.
Cable TesterFor cables with the following connectors:-XLR (3-pin)-XLR (5-pin)-6.3mm jack-RCA--DIN (up to 8 pin)-banana plug-Speakers (2-, 4-, 8-pin)-USB A-RJ45*LED error indicator, adjustable per contact via selector switch*Acoustic and optical continuity test via enclosed test leads*LED battery status indicator*Robust metal housing*Power supply via 9 V block battery (not included)*Abmessungen 112 x 60 x 190 mm*Gewicht 800 g
-
product
VME Bus Tester
VBT100
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
product
Portable Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ Metal shell, nice appearance design.◆ Available to save 2000 groups test results.◆ Support hardness conversion among HRC, HRA, HRB, HV, HB, etc, can convert 2 different scales simultaneously.◆ 4” LCD to display hardness result, conversion results, Max, Min,Mean value;◆ Support blue tooth printer, with RS232 to connect computer for software running;◆ Can test all kinds of metal which more than 5kg;◆ Indicating error ±5HLD, conform standard ASTM A956;◆ Support 7 types of impact devices.
