Sources
The origin.
-
Product
Trace-Level Dilution Calibrator
Model T700U
-
Teledyne Advanced Pollution Instrumentation
The Model T700U is a microprocessor based calibrator for precision, trace-level gas analyzers. Using highly accurate mass flow controllers combined with compressed sources of standard gases, calibration standards are provided for multipoint span and zero checks using up to 4 gas sources.In addition to the features of the Model T700, the Model T700U is designed for the demanding requirements of trace-level measurements. The ability to calibrate and verify linearity for NO2 at levels below 50 ppb is difficult with standard calibrators. To overcome this limitation, the Model T700U ozone generator operates in two modes; a high range with similar performance to the Model T700 ozone generator, and a low range, or "fractional" mode, for producing accurate ozone levels down to 3 ppb. To ensure the highest accuracy of NO2 output, the calibrator measures the ozone concentration prior to performing a GPT, and the range is selected automatically by the Model T700U based on ozone concentration and flow specified by the user.
-
Product
Custom Gas Measurement System
PA201
-
Gasera’s PA201 custom gas measurement system is a gas cell with an integrated detector that can be combined with different types of laser sources, making it an extremely versatile research tool. It also includes the gas exchange module that makes it extremely easy to use.
-
Product
Three-Phase AC Power Source 320 Vrms, 18 KVA, 5000 Hz
AC6918H
-
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
Product
PCI-6518, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Source Outputs, Bank-Isolated Digital I/O Device
779084-01
Digital I/O
The PCI-6518 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6518 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6518 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
Power Sensor and SNS Noise Source Cables (3 m/10 feet)
11730B
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
6-Zone SMT Reflow Oven
CR6000
-
A combination of high-mass heat sources and efficient thermal transfer allows the CR6000 to provide excellent reflow soldering results and throughput with a shorter-than-average heating tunnel. Your 6-zone unit also includes advanced features such as a wide combination pin-over-mesh belt conveyor, partnered pre-loaded KIC Auto Focus profile predictions software, and real-time thermal profiling standard.
-
Product
Pocket-size PAR logger
DEFI2-L
-
DEFI2-L is a high-precision photometer for long-term observations (up to 573 days for 1 minute interval observation). The cosine correction allows the sensor to have an excellent spectral sensitivity even when the light source is not directly above the sensor. Also, AAA alkaline batteries used by DEFI2-L are easily available, reducing the operating costs.
-
Product
Open Source Implementation fo the Open Management Group (OMG) Data Distribution Service (DDS)
Cyclone DDS
-
Cyclone DDS is the new fastest growing Open Source implementation of the Open Management Group (OMG) Data Distribution Service standard (DDS). Today, Cyclone DDS is gaining momentum in the Robotics, the Autonomous vehicles and the Automotive markets as well as in other mission critical and demanding IoT systems where:- Performance,- Robustness,- Safety ,- Security,- Interoperability, and- Opennessare fundamental for the success of these systems.
-
Product
VP Power Meter
UVP-365
-
This is the standard measurement instrument to measure absolute UV vaiue. All SAN-EI's UV light source fixtures are measured by this meter.
-
Product
JTAGulator 24-Channel Hardware Hacking Tool
32115
-
On-chip debug (OCD) interfaces can provide chip-level control of a target device and are a primary vector used by engineers, researchers, and hackers to extract program code or data, modify memory contents, or affect device operation on-the-fly. JTAGulator is an open source hardware tool that assists in identifying OCD connections from test points, vias, or component pads on a target device.
-
Product
Fiber Test & Measurement
-
Thorlabs manufactures a range of devices for testing and measuring the performance of optical fiber. Power, spectral signature, polarization, or end face surface geometry can by characterized with out-of-the-box solutions from our catalog. EO modulators, optical switches, and light sources are available to treat light being used on a test bed.
-
Product
Light Dependant Resistance Measurement Trainer
-
Unitech Scales And Measurements Pvt. Ltd
L.D.R. Trainer comprises of light dependent resistor (LDR) fitted to the shaft, which moves inside the tube where lamp is fitted at the other end. Variable DC voltage source is provided to vary the light intensity. Digital indicator is supplied to measure the light intensity in terms of distance moved between LDR and light source.
-
Product
MultiMeter
TW3204
-
Techwin(China) Industry Co., Ltd
Multi-Meter TW3204 integrates both an optical power meter module and an optical light source module and can perform closed-loop tests by using both modules,and can also work individually. It is specifically designed for technical support personnel to test a variety of instruments with a single meter and thus satisfy the user by providing a choice of greater convenience and more advantages.
-
Product
Load Cell Power Supply
MODEL PSMR
-
The PSM-R is a self contained AC power bridge excitation supply. This device consists of a low interwinding capacitance AC transformer and a high stability adjustable linear regulator designed specifically for driving transducer bridges. DC excitation is adjustable from 4 to 15 volts output and is capable of supplying 0 to 150 mA in output current. It features remote sensing to eliminate line drop errors and very low noise. It can also be used as a high quality voltage source or reference in many applications. AC input requirements are 105 to 125 VAC at 60 Hz.
-
Product
Near Field Probes 30 MHz up to 6 GHz
XF1 set
-
The XF1 set of near field probes consists of 4 passive near field probes and one passive E field probe for making measurements in the development phase of the magnetic and electric fields in ranges from 30 MHz to 6 GHz. Due to their integrated impendance matching, the probes are less sensitive in the lower frequency range than the RF type probes. The probe heads of the XF1 set allow for the step by step identification of interference sources of the magnetic field on an electronic assembly. At first, for example the XF-R 400-1 detects the fields which the assembly emits in total. Next, using higher resolution probes the interference sources can be more precisely detected. The E field probe is used for the detection of electric interfering fields near the assemblies. With trained use of the near field probes, field orientation and field distribution can be detected. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
100 Watt Dynamic Measurement DC Source, 20V, 5A
66332A
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections. The Keysight 66332A Dynamic Measurement dc Source provides dynamic measurement and analysis of voltage and current waveforms. It is ideal for testing digital wireless communications products/components because it not only provides the power for testing, but also performs the peak current measurements required to characterize the pulsed current demands of these products.
-
Product
PXIe 5-channel Source/Measure Unit, 500 kSa/s, 100 pA, 30 V, 500 mA
M9614A
Source Measure Unit
The Keysight M9614A is a PXIe five-channel source / measure unit (SMU). It supports accurate measurement up to 30 V / 500 mA with resolution down to 6 μV / 100 pA.
-
Product
Imaging Luminance Meter
CX1000
-
Hangzhou Hopoo Optoelectronics Technology Co., Ltd
CX-1000 imaging brightness meter is used to measure the brightness, brightness distribution and uniformity of LED modules, lamps, lamps, displays, street brightness and other light sources.
-
Product
Amplified Spontaneous Emissions (ASE) Sources
-
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
Product
Protection Test Set
COMPANO 100
-
COMPANO 100 is the universal and easy-to-use solution for all types of basic testing duties in electrical energy systems. Controlled electronic sources allow the user to obtain exactly the desired value and to output signals with variable frequencies and other signal forms, automated ramps, and pure DC.
-
Product
PXIe-4135, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit
783762-01
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 10 fA Precision System PXI Source Measure Unit - The PXIe-4135 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology and native triaxial connectors help you perform high-precision measurements with a current resolution of 10 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4135 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
Product
VLSI Test System
3380D
Test System
The 3380D/3380P/3380 test system have 4 wires HD VI source and any-pins-to-any-site high parallel test (multi-sites test) functions (256 I/O pins to test 256 ICs in parallel) that can meet the upcoming higher IC testing demands.
-
Product
Electronic Pressure Comparator
-
Huaxin Instrument (Beijing) Co., Ltd
When it comes to simultaneous pressure calibration for several pressure measuring instruments, electronic pressure comparator is always a great choice for most of people. The comparison calibrator features 5 pressure ports which allow simultaneous connection of 4 pressure gauges under test, making calibration more efficient and time saving. It also comes with an external air source for easy and precise pressure generation and servo valve for stable pressure control.
-
Product
Total Luminous Flux Measurement System
-
This system enables the total luminous flux measurement of luminous intensity distribution 2 and 4 light sources based on the measurement standards of LED lightings LM-78 and LM-79 approved by IESNA (Illuminating Engineering society of North America) .
-
Product
Audio Analyzers
-
Audio analyzer provides fast, accurate measurements including frequency, AC or DC level, distortion, SINAD and signal-to-noise ratio. It also includes an audio source providing accurate low distortion signals over wide frequencies and level ranges.
-
Product
Dopant Source
-
Attain precise and stable control of relatively low fluxes for dopant constituents in molecular beam epitaxy (MBE) through this compact dopant source. Its small thermal mass gives it excellent responsiveness, reproducibility, and stabilization for advanced doping profiles, plus consistent flux uniformity across an entire platen. Efficient cell heating minimizes thermal load.
-
Product
SGMA RF Source
SGS100A
-
The R&S®SGS100A is an RF source designed to meet the requirements of automated test systems. It is available as a CW source or as a vector signal generator with an integrated I/Q modulator. With its frequency range of up to 12.75 GHz, the vector signal generation version covers the essential digital signals. The CW version can be used as a flexible local oscillator and for interference testing against mobile radio standards.
-
Product
Hand Held Loss Test Set with Return Loss Option
LTSH1315
-
The KD Optics LTSH1315 is a combined laser or LED source and power meter designed to make attenuation testing in the field easy, reliable and consistent. A return loss option is available for 850nm multimode, 1310nm and 1550nm singlemode.
-
Product
Fixed Laser Source Module
Laser Source
Keysight offers a broad choice of fixed laser sources, which are available as single-wavelength and dual-wavelength modules as part of the Keysight Lightwave Solution Platform. The Keysight 8165xA Fabry-Perot laser sources can be used in conjunction with optical power meter modules for insertion loss, optical return loss and PDL measurement of broadband components and fiber. The Keysight 81663A Distributed Feedback Laser Sources are best suited for amplifier test and WDM system test applications. Keysight covers PON and common WDM wavelengths with its 81663A Distributed Feedback (DFB) laser source modules. The precise tunability around ITU-grid center wavelength gives you the flexibility to match test setups to the latest requirements of the DWDM-system. The fine-tuning allows to shift the center wavelength from one DWDM transmission channel to the adjacent channel in dense WDM systems. The built-in isolator ensures highest laser stability, even when reflections are present in the optical path.
-
Product
Composite 1×24 Video Distribution Amplifier
VDA124RM
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
