Earth Leakage Circuit Breaker Testers
test trip time and trip current values.
-
Product
High Pressure Leak Tester
HPT 500
-
A cost-effective, safe alternative that will change standard practices for heavy duty preventive maintenance and repair.
-
Product
Earth Fault Detector
K-3838
-
Kongter Test & Measurement Co., Limited
Kongter’s K-3838 earth fault detector is the updated model which is developed to fast detect, trace and pinpoint virtual grounding faults on LIVE DC systems where electrical cables have breakage and current lost to ground. It will save you from long time unnecessary troubleshooting and helps to increase the reliability of your electrical equipments. Our unique technique makes it safe and fast to handle earth fault in DC systems that are working online.
-
Product
HIGH-VOLTAGE TESTERS 0-10KVac UP TO 0-40kVac
AV-100VA-5V
-
HIGH-VOLTAGE TESTERS 0-10KVac UP TO 0-40kVac
-
Product
Cylindrical Mandrel Bend Tester
1506
-
The Elcometer 1506 Cylindrical Mandrel Bend Tester is robust and used to determine the elasticity, adhesion and elongation properties of cured coatings on sheet metal.
-
Product
Oil Tan Delta Tester
OTD
-
The Oil Tan Delta (OTD) is a laboratory instrument, which measures the Tan Delta, Resistivity and Relative Permittivity of insulating liquids. These tests give a wider picture of the overall quality of the insulating oil, and will indicate if there is any contamination. Megger has developed features of the OTD to ensure that productivity levels within laboratories are maximised. The microprocessor controlled inductive heater means that there is uniformity of temperature throughout the cell, in compliance with IEC 60247, and for cooling a fan effectively speeds up the cell cooling time. The instrument has a temperature measuring range of 10 to 110 C, with an accuracy of 1 C. It can be set to preheat before testing takes place. The automated oil drain facility negates the need to move the oil vessel. User safety is paramount and with this in mind, Megger have designed independent and dual redundant high voltage cut-off circuitry. If for any reason the user needs to abort the test, this can be done so by pressing any key, immediately terminating the test and removing the high voltage. The design of the cell components maximise oil fill rate but minimise turbulence in oil flow and eliminate trapping of air. With only 32 cell components, it is easy to assemble and disassemble.
-
Product
Rubber Testers
-
TA Instruments introduces a complete line of new instruments for the measurement of rheological and physical properties of polymers, rubber and rubber compounds at all stages of manufacture. The new rubber testing instruments include a Rubber Process Analyzer, Moving Die Rheometer, Mooney Viscometer, Automated Density Tester and Automated Hardness Tester.
-
-
Product
Automatic Winding Turns Tester
-
This tester has the advantage of high accuracy and efficiency, limited influence due to the form and size of the coil to be analyzed, and fast & easy operation thanks to the precision sensor and microprocessor that adopt the patent know-how developed by the manufacture. This tester, when in operation, does not need any further adjustment and calibration. Just connecting the clip leads to each terminal lug of the coil winding, then the tester instantly shows the exact number of the winding turns on the digital display. Unlike other similar devices, input the data of standard coil to test against is unnecessary. In this way, this tester greatly upgrades the inspection and analyzing efficiency.
-
Product
Prodution Testers
Effitest E50
-
Effitest e50 is a flexible and cost efficient solution with easy programming, debugging of test programs and life-cycle support.
-
Product
Laboratory Equipment Temperature and Humidity Tester
CX-P002
-
Shenzhen Chuangxin Instruments Co., Ltd.
Temperature & Humidity Test Chamber It's used for testing the performance of heat-resisting, cold-resistant, dry-resistant and moisture-proof of different materials
-
Product
Wire Crimp Pull Tester (Manual)
WT3-201
-
The WT3-201 wire crimp pull tester is designed to measure the pull-off force of crimped wire and tube terminations. An ergonomic lever allows for easy application of up to 200 lbF (1,000 N) of crimp pull force. Adjustable wire terminal grip contains multiple slots for wire diameters up to AWG 3 (0.25 in [6.3 mm]). The tester accommodates most insulation types. Samples can be sent to Mark-10 for evaluation prior to purchase.
-
Product
DMX Tester Portable
DTR-HH
-
The DTR-HH is a DMX 512 tester data send / receive unit with 10 store and recall preset scene snapshots. Each of the 10 presets will store 512 channel levels including the packet size and start code. Each preset can be edited to precise values and recalled anytime.
-
Product
E1 Testers
-
GAOTek provides a large collection of high quality, affordable E1 testers that are specially manufactured to speed up the ethernet maintenance time and work efficiency for sale to the United States, Canada and Globally. These devices consist of PING, router trace, a port location tool, a loop-back tool and offers a variety of Ethernet diagnostic functions. These E1 Ethernet test instruments are all incorporated with test tools for E1, V port, and Gigabit Ethernet link repairs, and failure diagnosis. E1 Ethernet testing devices are user-friendly, can be used in Ethernet cable tests, flux error code tests, connectivity performance, traffic testing, ethernet wire testing, and bandwidth verification. As these devices help in measuring and proving performance for criteria Ethernet networks they are commonly used in the RFC2544 performance test.
-
Product
Petroleum Distillate Tester
-
Weshine Electric Manufacturing Co., Ltd
Weshine invented Petroleum Distillate Tester(VS-9815 Series) is designed and manufactured in accordance with the standard of ASTM D86, which is applicable to determine quantitatively the boiling range characteristics of such products as natural gasoline, light and middle distillates, automotive spark-ignition engine fuels, aviation gasoline, aviation turbine fuels, 1-D and 2-D regular and low sulfur diesel fuels, special petroleum spirits, naphthas, white spirits, kerosines, and Grades 1 and 2 burner fuels.
-
Product
Earth Bond Test Set
EC-12
-
The Earth bond test is a basic safety test prescribed in many standards to test samples for the integrity of earthing continuity throughout the sample.
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
Multimode Single-Mode Fiber Tester Kit
KI-TK074
-
1310/1550 nm & 850/1300 nm source & Autotest power meter + acceptance reporting software. Interchangeable SC & LC connectors
-
Product
Hand Held Video Tester
-
The hand held video tester is our world class video hardware and VIDSoft suite integrated to a micro PC via ATTI’s slot-0 service. The intent of the slot-0 service is to eliminate the bottleneck of VISA and PCI bridging.
-
Product
Film Permeability Tester
-
Film Permeability Tester is designed to test the permeability of a wide range of packaging materials such as plastic film, composite film, aluminum foil, thin sheets, rubber, porcelain, medical patch, etc.
-
Product
Network Cable Tester
PHCT45
-
This Pyle network cable tester checks RJ45 and BNC network cables for continuity and correct polarity. LEDs show the status of each pin. , perfect for the IT guy on the go.
-
Product
Gold Tester
-
Napco Precision Instruments Co
Provides the lowest cost option for gold purity analysis needs. A proportional counter system, this the lowest priced X-ray fluorescence unit in the gold tester filed.
-
Product
Automatic Huge Drop Tester
KD-8688
-
King Design Industrial Co., Ltd.
Reliability & Photovoltaic (PV) Testing Equipment.
-
Product
Ground Resistance Tester
-
Weshine Electric Manufacturing Co., Ltd
1.Soil resistivity tester supports 2, 3 and 4wire grounding resistance measurement. 2. 4digit large LCD display with white screen backlight, suitable for use in dimly lit places. 3. IP65 protection grade, good waterproof, compact and portable, supports multiple functional tests.
-
Product
Spring Back Tester
HTJ-16
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3; Inspection standard: JB/T4279.4-2008Used to measure the spring back characteristic of enameled round wires with nominal conductor diameter of between 0.080mm and 1.600mm;Number of winding turns: 5 turns and a halfStop accurately at zero position of the scale after automatic windingAs soon as the value of spring back angle stop counting, the dial will stop to rotate immediately, so that the value displayed on LED and read on the dial are the same.Sensor is unnecessary to be adjusted for samples of different specificationsCoils loosen slowly during spring back, no action of spring back or jump suddenly.Application of SCM control allows for fast operation and strong anti-interference capacity;
-
Product
Multimeter Network Tester
VA16
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Network Cable test (RJ45): Tests for open circuits, shorts, miswires, reversals, and split pairs SHIELD detection tests a cabl
-
Product
Digital Insulation and Continuity Tester
Metra Insu 20
-
Measurement of the insulation resistance on electrically dead equioment and systems with test voltages up to 1000 V. For testing motors, transformers, generators, switchgears. For testing of house hold appliances. Measurement of the insulation resistance of cables. Very useful for on-site maintenance and service departments.
-
Product
Vehicle Battery Tester
6420
-
Peaceful Thriving Enterprise Co Ltd
This is a device to test the 12 volt lead-acid battery of any vehicle. The tester will focus on health condition analysis of vehicle battery; it will estimate the cold cranking ampere (CCA) of the vehicle, and predict the lifetime of the battery. This will be helpful for the technician to inspect and maintain the electrical system of the vehicle. Base on the inspection, user can predict the time to replace the battery.
-
Product
Rockwell/Superficial Rockwell Twin Hardness Tester
900-375
-
Our latest Phase II analog Rockwell Hardness Tester, the 900-375, tests both Rockwell hardness and Superficial Rockwell hardness in one unit, with state of the art design and dynamic precision only found at Phase II. The Phase II Twin Rockwell/Superficial Rockwell hardness tester is ruggedly engineered to obtain highly sensitive and accurate readings.
-
Product
Drop Tester
KD 688 A
-
King Design Industrial Co., Ltd.
*PLC control, linear motor fast speed control the height setting.*Alarm warning before testing.*Light support structure decreases the test impact.*Support dropping very smooth with dual lubrication guide.*No second impact. *A data acquisition for the impact wave record (Option).*Non maintenance request for continue operation.*According to ISTA, ASTM .....etc international standard.*Equipped edge & corner holder.
-
Product
Hot Temperature Hardness Tester
1200C
-
Rtec high temperature hardness tester is used to do high temperature materials testing up to 1200C. To prevent oxidation of tip and the samples the high temperature indenter comes with sealed chamber with inert gas. High resolution programmable down force control and XY stage allows to do multiple indents on same or multiple samples with ease.
