Functional Test
black box type testing via interface level inputs and resulting output analysis.
See Also: Functional ATE, Functional Test Systems, Interoperability Test, End of Line
-
Product
CPCIe (PXIe) Module
ACS-FC-3U-2
-
The ACS-FC-3U-2 is AIM’s high performance CPCIe (PXIe) module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The ACS-FC-3U-2 is a powerful State-of-the-Art 4-lane CPCIe 2.0 compliant CPCIe board.
-
Product
PXI Precision Resistor Module, 9-Channel, 2 to 6.97k
40-297-030
-
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Digital Functional Test
CTS100i
-
Capable of performance testing to defined traceable standards, CTS100i is designed to test Military, Aerospace and Safety-Critical equipment. CTS100i is a cost-effective digital functional test system, available in single, dual and three bay versions.
-
Product
High-Speed Digital Testing
-
Silicon Turnkey Solution, Inc.
High-speed devices create significant challenges for functional testing, for example, the need for high-bandwidth interfacing to maintain signal integrity at multi-gigabits per second data rates and the ability to measure high-speed bit error rate and jitter. STS brings extensive experience in high-speed functional testing for commercial, military and aerospace devices to meet the most stringent customer requirements. Our highly integrated testing laboratory and efficient workflow are designed with one goal in mind: to shorten time-to-market and enhance our customers’ ability to compete.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Installation Tester
M75
-
Installation tester for safety tests according to IEC/EN61557-1 with TRMS multimeter functions and test of cable mapping on lan RJ-45 networks
-
Product
64 MB RAM Tester
IST-6500
-
IST Information Scan Technology, Inc.
The IST-6500 is a low cost, fully programmable tester for functional and parametric testing of DRAM, SRAM, VRAM, and SIMM devices up to 144 bits wide and 64 MB in size. The 6500 offers four different ways to automatically measure the access time of these devices from 2ns to 160ns with a resolution of 2ns. The DRAM timing parameters are programmable at the resolution of 1ns to allow for testing DRAM, SIMM, or VRAM at their required operating speeds, thus providing real time test conditions.
-
Product
PXI Precision Resistor Module 9-Channel, 2 to 26.7k
40-297-032
-
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXIe Avionics Interface Cards
-
The OmniBus II PXIe is the next-generation of Astronics' popular OmniBus product with faster I/O and processing capabilities. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box. Readily available as Commercial Off-The-Shelf (COTS) products, the PCIe interface is perfect for challenging simulation, test, interface, and data recording applications.
-
Product
FiberPulse OTDR
XO1
-
FiberPulse OTDRs send pulses down fiber optic networks from one end of the fiber, displaying a trace and reporting all detected events such as splices, connectors, macrobends and fiber ends and breaks. The total fiber length is reported along with name, location, loss and reflectance of detected events. The intuitive keypad design features integrated shortcut keys designed for quickly positioning and analysing events. Another feature of this unit is the Live Optical Signal Detect Function, which tests if the fiber is live before sending the pulse, this can effectively prevent accidental damage to the OTDR and attached communication equipment.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 2.97M
40-297-151
-
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Thermometer / Cardiac / Invasiv, non Invasiv Blood Pressure Simulator
TBH-400
-
Test device for functional testing of medical thermometers (DIN EN ISO 80601-2-56), cardiac output, invasive (IEC 60601-2-34) and non-invasive blood pressure devices (IEC 60601-2-30).
-
Product
AC Hipot Test Set
-
Weshine Electric Manufacturing Co., Ltd
AC Hipot Test Equipment for Dielectric Withstand Test are suitable for 50 / 60 Hz AC testing of low capacity test objects. Optionally, these units can also be upgraded to function as DC test sets by mounting the rectifier attachment on top of the transformer.Weshine® AC Hipot Test Set for AC hipot test can be equipped with a rectifier attachment for DC voltage testing.Typical application areas:Testing of cables Testing of switchgearTesting of transformersTesting of CP & PTTesting of MV systems
-
Product
PXI Precision Resistor Module 4-Channel, 2 to 26.7k
40-297-132
-
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 6.97kΩ
40-252-030
-
The 40-252-030 is a programmable resistor module with 2 channels which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
The all-in-one data logger for the entire vehicle networking
PM-200
-
The PM-200 sets the bar considerably higher on the topic of safeguarding and troubleshooting vehicles. Bus systems such as CAN, CAN-FD, FlexRay™, LIN, MOST150 and Automotive Ethernet are logged at a data speed up of to 120 MB/s. SSD removable media allow for quick evaluation and distribution of the data. Various upgrade options enable configuration for any application. Flexibility, programmability and support from debugging protocols make it possible to meet the high demands of functionality and fleet tests as well as of test runs.
-
Product
PXIe Vector Network Analyzer, 300 kHz to 20 GHz
M9374A
-
Pay for only the frequency range you need with a choice of six frequency ranges up to 26.5 GHz Improve accuracy, yield and margins with the best PXI VNA speed, dynamic range, trace noise and stability Add functionality to your test system with a full 2-port VNA that fits in a single PXI slot Address your multiport applications needs by cascading multiple models Increase throughput and lower costs by adding modules in a multi-site configuration
-
Product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 31.5Ω
40-298-010
-
The 40-298-010 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
-
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 395kΩ
50-297-142
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Electric Safety Tester
PV-215
-
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 26.7kΩ
40-251-132
-
The 40-251-132 is a programmable resistor module with 2 channels which can be set between 2Ω and 26.7kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Test Type Packages
ProCalV5
-
ProCalV5 Test Type Packages are designed to support advanced paperless functionality with comprehensive testing and maintenance routines for a full range of complex systems and devices. All Test Type Packages shown below are already built and can be supplied as add-ons to your existing ProCalV5 installation.
-
Product
RoHS Video Mirror
MIR540
-
The MicroImage MIR540 is a high performance display processor capable of mirroring the video input on the X and Y axes. Each of the four selectable inputs may be individually mirrored horizontally, vertically or both. Mirroring on both axes is the same as rotating the image 180 degrees. A color bar test function is also available.
-
Product
MTM-Load-1: 1-Channel DC Load Module
-
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.
-
Product
4500~6000W DC Electronic Loads
JT634 Series
-
Nanjing Jartul Electronic Co., Ltd
JT634 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT634 series load very suitable for testing power supply when produced in large quantity. Besides, JT634 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT634 series load satisfing most of R&D requirements. Moreover, JT634 series load’s special parallel operation method can satisfy the synchronous loading requirements of multi-channels output power supply and satisfy single-channel output power supply requirement for big power.
-
Product
Test Solutions Services
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
Product
In-Circuit Tester
Sparrow MTS 30
-
The Sparrow MTS 30 is a 19“ test system that can be integrated into any standard rack. The In-Circuit tester can also be used as benchtop test system. With this compact and flexible tester you can perform both analog and digital In-Circuit and functional tests.
-
Product
Test Equipment
-
Concentric Technology Solutions, Inc.
If you are looking for a Bluetooth, RFID, or DMB/DAB test equipment, Concentric Technology Solutions, Inc. (CTS) have the right tester for your testing needs. Our testers give our clients all the right features you need – whether it’s full compliance testing or just to test functionality. CTS has the solution to meet your needs.
-
Product
Functional Testing
-
Thanks to our partnership with 6TL engineering (www.6tlengineering.com), we can build complete ATE (Automatic Test Equipment), i.e., turnkey solutions for your testing needs using, high quality, efficient, and modular base test platforms with a short delivery time.
