-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-03
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
product
Power Quality Analyzer
PQM-703
Power quality analyzer PQM- 703 is a technically advanced product that allows for comprehensive measurements of the quality of electricity , analysis and recording of power network parameters, for frequencies 50/60 Hz in accordance with European standard EN 50160. PQM -703 is another representative of a well, known family of analyzers line PQM- 70x . In relation to the PQM -702 has new functions like recording of transients with max. sampling frequency 10 MHz (rapid changes in voltage) and control signals. Minimal transient capturing time is 650 ns. It is intended for a very wide range of users who need to control the quality of power with a mobile device , which fulfills the requirements of a multi-sheet standard IEC 61000 for class A analyzers. This applies to measurement accuracy, measurement methods, and synchronization of time with a standard signal. The last condition is met with a built-in GPS module with an internal antenna. If the analyzer is installed inside, it is possible to use an additional antenna with a 10m-long wire. If the antenna is situated outside, GPS signal will be attainable without any problems and used for the synchronization of an internal clock.
-
product
Custom Radio Direction Finding Products
This assembly contains three sets of antennas, three RF summers, an antenna switch, a GPS and (optionally) a flux gate compass. The pod mounts to the roof with nylon straps, although it is recommended that it be bolted down for more permanent applications. Although this antenna is not stocked, we can provide them on relatively short notice. No minimums apply.
-
product
PDS Motionscan Software
Allows a 3D Scanning sonar user to collect motion compensated 3D point clouds from a moving platformTeledyne PDS MotionScan system allows a 3D Scanning sonar user to collect motion compensated 3D point clouds from a moving platform. The MotionScan system is comprised of: an RTK capable dual antenna GPS with precision heading output, a heave, pitch and roll sensor, a topside control console. In combination with a BlueView 3D Multibeam Scanning Sonar this creates a full survey package.
-
product
Automatic Flight Inspection System
AT-930DG
Fully Automatic OperationAll-Weather CapabilityDifferential GPS Position ReferenceHigh Accuracy and Maximum ReliabilityWindows User Interface SoftwareEasy to Operate and Easy to LearnMinimum Maintenance RequirementsModular System ArchitectureLong-Term Supportability
-
product
Compact Timing Systems
NanoSync IV & NanoSync IV Low Profile
The NanoSync IV is a small form factor GPS Position, Navigation, Time (PNT) and Frequency reference system that provides multiple reference outputs and includes support for NTP & PTPv2 IEEE 1588-2008. The NanoSync IV has a Rubidium oscillator and is available with a civilian C/A GPS receiver or SAASM (Rockwell-Collins MPE-S GB-GRAM or Trimble Force 22E MRU GPS receiver) for military users. The NanoSync IV is packaged in a small, rugged enclosure ideally suited for embedded electronic warfare applications.The NanoSync IV-SA-Rb has been demonstrated to be compliant to the Joint Airborne SIGINT Architecture (JASA) Version 3.0, Annex 1, for Time, Frequency, Navigation and Geodesy (TFNG), making it suitable for Electronic Warfare (EW) COMINT and ELINT applications in fixed site, airborne and shipboard environments.
-
product
Kitting
Astronics' manufacturing and kitting capabilities offer the most cost-effective and high-quality system installation kits for IFE, Broadband, Wi-Fi, TCAS, GPS, EGPWS, FMS, SatComs, IFE, DBS TV, Air to Ground Telephone, BRNAV, VHF and HF Communication systems.
-
product
Talon 3.6 GS/sec Ultra Wideband RF/IF Rugged Portable Recorder
Talon RTR 2729A
- Video: A Quick Look at RTR 2729A Talon Rugged Portable Recorder- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9"D x 13.0" H- Lightweight, just less than 30 pounds- Sample rates up to 3.6 GHz in single-channel mode- Sample rates up to 1.8 GHz in dual-channel mode- 12-bit A/D, with 16- and 8-bit packing modes- Capable of recording RF/IF frequencies to 1.75 GHz in single-channel mode- Capable of recording RF/IF frequencies to 2.8 GHz in dual-channel mode- Real-time sustained recording rates of up to 4.0 GB/sec- Windows® 7 Professional workstation with high-performance Intel® Core™ i7 processor- Up to 61.4 terabytes of SSD storage to NTFS RAID solid state disk array- SystemFlow® GUI with Signal Viewer analysis tool- Optional file headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 10-36 VDC power supply
-
product
GPS Frequency Standards
Precision Test Systems manufacturers' a full range of GPS and GNSS frequency standards that are disciplined to most of the worlds satellite systems.
-
product
200 MS/sec RF/IF Rugged Portable Recorder
Talon RTR 2726A
- Designed to operate under conditions of shock and vibration- Portable system measuring 16.0" W x 6.9" D x 13.0" H- Lightweight: just less than 30 pounds- Shock-and-vibration resistant SSDs perform well in vehicles, ships and aircraft- 200 MHz 16-bit A/Ds- 800 MHz 16-bit D/As- 80 MHz record and playback signal bandwidths- Recording & playback of IF signals up to 700 MHz- Real-time sustained recording rates of up to 3.2 GB/sec- Windows® workstation with high-performance Intel® processor- Up to 30.7 TB of SSD storage to NTFS RAID solid state disk arraySystemFlow® GUI with signal viewer analysis tool- File headers include time stamping and recording parameters- Optional GPS time and position stamping- Optional 18-36 VDC power supply
-
product
Antennas
Welcome to our range of industry-grade antennas here at RF Solutions. As a leading supplier of cutting-edge RF products, we offer antennas that are essential for projects requiring efficient transmission and reception of electromagnetic waves. Choose from a wide selection of GSM, GPS, and WiFi antennas, available in various frequencies and designs to suit diverse applications. Our high-performance WiFi antennas are perfect for extending signal range and enhancing connectivity in both commercial and industrial settings.
-
product
2 Way GPS / GNSS Signal Splitter IP67 Outdoor, SMA, 1-2 GHz, 50 Ohm, Passive
GPS211
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portTri Alloy SMA Female (Jack) 50 Ohm
-
product
Precise Timing
Schweitzer Engineering Laboratories, Inc.
Precise timing is achieved using satellite clocks, which process signals from Global Navigation Satellite Systems, such as GPS, and output time to power system devices using IRIG-B, the Precision Time Protocol (PTP), and the Network Time Protocol (NTP).
-
product
IO Expander
AD16x2DA16x8-125ETH
The IO Expander is an additional module to provide more input and output capabilities to the AD16x2DA16x8-125ETH. Via high speed link it connects 8 TTL inputs, 16 TTL outputs, 8 SPDT RF switches, and a GPS module.
-
product
Survey Systems
Pair the Smart Chamber with a gas analyzer of your choosing and connect using your mobile device or laptop via the built-in Wi-Fi web server. See live flux data with a LI-COR gas analyzer or connect to a third-party analyzer and the chamber will log GPS and ancillary data for your flux measurements.
-
product
Low Pass and Bandpass SMA Coaxial Filters
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
-
product
Communication Data Logger
LE-270GR
LE-270GR is a Communication Data Logger, which has acceleration sensor and a connector for GPS antenna. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data or GPS data on the PC at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on PC. It has galvanic-isolated two CAN transceivers and two LIN transceivers. Thus you can measure 2 channels of CAN/LIN communication lines and can simultaneously register GPS positioning data, acceleration data, and voltage data of 4 external signals.
-
product
Universal Clock
DXD-16
The DXD-16 Universal Clock is a PTP Grandmaster clock with GPS receiver and a multi-format legacy reference generator. While working in a PTP environment, the DXD-16 keeps legacy equipment perfectly synchronized with the IP infrastructure, or vice-versa.
-
product
CARTHE GPS DRIFTER
The low-cost sacrificial CARTHE drifter tracks currents centered 40 cm below the surface and is designed to enable large-scale deployments. The patented design was developed by a team of physical oceanographers and engineers at the University of Miami.
-
product
GPS, GLONASS, Galileo Micro Splitter 2 Way, SMA, 1176.45 - 1602.00 MHz, 50 Ohm, Passive
GPSL15
INSTOCK Wireless Components, Inc
GPSL15 is a two way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Max voltage rating at the DC blocked port is 10 VDC; maximum current rating is 50 mA. Maximum voltage rating at the DC pass port is 50 VDC; max current rating is 1000 mA. Furnished with SMA female connectors all ports. Being a "micro-sized" splitter, GPSL10 weighs only 21 grams and is suitable for applications requiring low-weight parts.
-
product
Timing Modules
Quartzlock provides Timing Modules for network timing, reference disciplining to various input references such as 1PPS, GPS receiver and Frequency References.
-
product
Trunk Amplifier
The trunk amplifier is designed to compensate for attenuation and additional amplification of signals from GPS and GLONASS satellite radio navigation systems as part of synchronization and common time equipment.
-
product
GPS Antenna Signal Splitter 6 Way, N Type, Passive, L1 & L2, 50 Ohm
GPS600
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo SplitterLow Insertion Loss (0.3 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portsRoHS Compliant Splitter Construction
-
product
GPS, GLONASS, Galileo Splitter 2 Way, N Type, 1000 - 2000 MHz, 50 Ohm, Passive
GPS200
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)15 VDC & 75 mA max on DC block portTri Alloy N Type Female (Jack) 50 Ohm
-
product
Frequency Standards
Precision Test manufacturers a complete range of frequency standards. This includes rubidium and OXCO models either free running or controlled by an external reference (GPS, GLONASS, Galileo, 1pps, 5 MHz, 10 MHz, IRIG-B etc). Output frequencies typically 1 MHz, 5 MHz, 10 MHz, 10.23 MHz, 13 MHz, 100 MHz or bespoke frequency.
-
product
GPS
A device that receives signals from GPS satellites to help a device determine its location.
-
product
8 Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - SFF
Model 6353
- Small form factor rugged enclosure- Conduction-cooled- Designed to the IP67 specification for dust and water immersion- Sealed military-grade circular connectors- Incorporates Xilinx® Zynq® UltraScale+" RFSoC FPGAs- 16 GB of DDR4 SDRAM- On-board GPS receiver- Optional dual 100 GigE UDP optical interface- Optional fan cooling for benchtop use- Navigator® BSP for software development- Navigator® FDK for custom IP development- Pentek's Quartz Family of Xilinx Zynq UltraScale+ RFSoC FPGA Products Video- Live Signal Acquisition Video: Quartz Model 5950 and Model 6001 RFSoC boards- Pipeline Newsletter: Strategies for Deploying Xilinx's Zync UltraScale+ RFSoC- Please refer to the product datasheet for Installed FPGA IP Module details
-
product
Test Adapter / Pneumatic Adapter
GPS testing technology offers a wide range of pneumatic adapters. The support with compressed air results in increased ease of use and larger pressures can be built up easily and thus more test needles can be contacted.
-
product
3.0 GS/sec Ultra Wideband RF/IF Rugged Rackmount Recorder
Talon RTR 2745
- Two 3.0 GHz 14-bit A/Ds- Two 2.8 GHz 16-bit D/As- Real-time record/playback rates up to 6.4 GB/sec- Integrated DDCs and DUCs- Capable of capturing RF signal frequencies up to 3 GHz- Captures and reproduces IF bandwidths up to 560 MHz- Captures baseband bandwidths up to 1.5 GHz- 4U 19-inch rugged rackmount PC server chassis- Windows® Professional workstation with high performance Intel® Core™ i7 processor- Designed to operate under conditions of shock and vibration- Removable SSD drives- Up to 61 terabytes of storage in integrated NTFS RAID disk array- Selectable RAID levels of 0, 1, 5, 6, 10 and 50- SystemFlow® GUI with signal viewer analysis tool- C-callable API for integration of recorder into application- Optional GPS time and position stamping
