BERT
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: Bit Error Rate Testers
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) With Eye Checker
RB3004
-
*Low cost continuous 4ch, 1G to 30Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
HDMI/Display Port Checker with 4ch x 12Gb/s Tunable BERT & EyeChecker
RB1204-HDMI/DP
-
*Low cost continuous 4ch, 1G to 12Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
Single Channel Error Rate Tester
Basic Bert
-
Already as a single channel BERT the PARALLEX® system offers full functionality for testing high speed components. PRBS and user pattern generation and error detection for 2..13Gbit/s.
-
Product
Economical Solution for Test Requiring Fewer Instrumentation Modules.
OPTOWARE-S200 (FOTS-Bench Top Series)
-
•LD Driver, EDFA, ASE Broadband Source, 1X4 Optical Switch•Variable Optical Attenuator, Wavelength Meter•SOA Driver, SLED Driver, Pump LD Driver•Pattern Generator & BERT, SFP Transceiver Driver•4Channel Optical Return Loss Meter (Light Source & Power Meter)
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Single Channel SFP+ All-In-One Sensitivity Tester
SFP+ Tester
-
All in one mainframe to perform a complete sensitivity test on a single channel fiber optic transceiver. Includes Clock source, BERT and all optical modules
-
Product
8-Channel 30 Gbaud/s PAM4 Bit-Error-Rate Tester
OptoBERT™ OPB-400G
-
The OptoBERT™ OPB-BERT-400G-P8 is the industry’s most compact, cost-effective, easy-to-use 8-channel 30Gbaud/s electrical bit-error-ratio tester (BERT) for testing components, cables and systems in R&D and manufacturing environments.
-
Product
High Throughput 1 ns Pulsed IV Memory Test Solution
NX5730A
Test Platform
Precise and fast characterization of new memory, such as spin transfer torque magneto resistive random access memory (STT-MRAM) from DC to high-speed pulsed IV measurement on silicon wafers Apply accurate and high-speed pulsed voltages (down to 1 ns pulse) to magnetic tunnel junction (MTJ) for STT-MRAM and precisely measure the resistance of MTJ Perform all typical MTJ characterization tests in one solution10 to 100 times faster cycle test, such as a bit error rate test (BERT)Capture and visualize MTJ switching waveforms clearly during the writing pulse Dedicated solution with Keysight Technologies’ technical expertise
-
Product
4-Channel 32 Gbps Bit-Error-Rate Tester
OptoBERT™ OPB-100G
-
The OptoBERT™ OPB-100G is the industry’s most compact, cost-effective, easy-to-use 4-channel 32 Gbps electrical bit-error-ratio tester (BERT) for testing components, cables and systems in R&D and manufacturing environments.
-
-
Product
International Test Set
930i
-
The 930i Communications Test Set is a multi function portable unit that features a powerful Next Generation Voice Test Suite. It offers a laboratory quality VF TIMS, a full-featured BERT, RS-232 control and a host of other functions as standard equipment.
-
Product
Multi-Channel Synchronization Module for M8190A, M8020A or M8030A
M8192A
Synchronization Module
Complex testing sometimes requires playing multiple waveforms in parallel (e.g. multi-emitter testing). The M8192A synchronization module allows engineers to synchronize up to 12 M8190A channels and fits into a standard AXIe frame.The M8192A synchronization module also supports testing of high-speed digital busses like PCI Express.Test efficiency can be increased by testing up to 10 lanes with the M8051A and the M8041A BERT modules in parallel. These can be synchronized by the M8192A module.
-
Product
Bit Error Rate Tester
100G NRZ BERT
-
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
Product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
-
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
Product
Electrical and Optical & Bit-Error-Rate Testers (BERTs)
OptoBERT™
-
The OptoBERT family of BERTs offers the best value in the industry for bit-error-ratio testing of optical and electrical components, subsystems and systems. OptoBERT family of products covers data rates from 100 Mb/s to 28.05 Gb/s.
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
E1 T1 Tester
NetProbe 2000 PDH
-
New Generation Analyzer for Legacy PDH networksThe NetProbe 2000 E1E3 is newest, state-of-the-art handheld analyzer on the market for testing the legacy E1 and E3 in PDH networks. It includes all features for E1 & E3 BERT and E1 physical layer testing. Automated line monitoring performs autocheck of essential alarms and errors.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
5Gbps Electrical & Optical Bit-Error-Rate Tester
OPB5000
-
The OPTELLENT OptoBERT™ OPB5000 is a cost-effective easy-to-use bit-error-rate tester (BERT) for testing datacom ICs, devices, components, modules and systems in R&D and manufacturing environments as well as field installations of Storage Area Networks (SANs). OPB5000 supports 4GFC, 2GFC and 1GFC. The OPB5000 tester is also ideal for Gigabit Ethernet, Infiniband (2.5G) and PCIe testing.
-
Product
NRZ Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
-
Product
Interference Source, 32 GHz
M8054A
Interference Generator Module
32 GHz interference source blade for the M8040A BERT.
-
Product
Bit Error Rate Testers
FarSync BERT Tester – USB
-
A Bit Error Rate sync and async communications line quality tester for a Windows Laptop/PC using a USB port. The FarSync BERT provides a comprehensive, simple to use, all in one, line testing utility for testing synchronous lines from your Laptop. There are no extra expensive modules to buy to test different line types.
-
Product
Hand Portable Test Instruments
-
GL’s PacketExpert™ 10G provides comprehensive testing of 10 Gbps wirespeed Ethernet/IP networks. It has two 10 Gbps Optical ports, and two 10/100/1000 Mbps Electrical/Optical ports capable of BERT, Smart Loopback, RFC 2544, ExpertSAM, Record and Playback, IPLinkSim™ and PacketBroker functionalities.
-
Product
Receiver Conformance Test Application for IEEE 802.3ck
M8091CKCA
-
Designed to assist and simplify the stress signal calibration used for testing the inputs of IEEE 802.3ck Draft 3.3 chip-to-chip (C2C) and chip-to-module (C2M) electrical interfaces using Keysight M8040A 64Gbaud Higher Performance BERT or an M8050A 120Gbd High-Performance BERT together with Keysight Digital Communication Analyzer (DCA) Oscilloscope or Infiniium UXR real-time Oscilloscope.
-
Product
Bit Error Rate Testers
FarSync BERT Tester – PCIe
-
A Bit Error Rate 2 port sync line quality tester for a Windows PC/Server with a PCIe slot. The FarSync BERT provides a comprehensive, simple to use, all in one, line testing utility for testing synchronous lines from your PC up to 20 Mbits/s. There are no extra expensive modules to buy to test different line types.
-
Product
Photoreceiver
-
A lightwave digital receiver module designed for OC-192, DWDM, and Bit Error Rate Testing (BERT) of a digital optical link. The LRD-10-M is an O/E converter with post/limiting amplifier module designed for use in receivers up to 12.5 Gb/s data optical transmission systems.
