Trailer Harness Testers
determine that a trailer's lighting is working. Trailer
See Also: Wiring, Wiring Analyzers
-
product
4-Pin Trailer Light Tester
3536C
Peaceful Thriving Enterprise Co Ltd
4-pin Small Size Trailer Light Tester & Circuit Troubleshooter for US, Plug tester into vehicles 4-pin connector and operate vehicle's turn signals, lights and brakes. When there is power present, the green light will glow.
-
product
Trailer Light Tester
Checkmate 1200
Checkmate 1200 is a good, basic light tester for trailer light systems that can also serve double duty to power anti-lock brake systems.
-
product
Trailer Buddy 4/5 Pin One Man Trailer Wiring Tester
220
*Tests 4 & 5 Pin Flat connector wiring *Each signal from vehicle emits a unique tone *Loud beep can be heard over shop noise *One person makes complete test in 30 seconds! *Just apply brakes, turn signals, running lights& engage reverse *Tester also emits unique tone for any shorts in the wiring! *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
product
LIGHT RANGER MUTT
TT9103
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
product
Light Testers
Hall’s have designed and manufactured products for oil, industrial, farming, commercial, and transportation markets. Products such as truck and trailer light testers, bop savers, early engine warning systems, oil spinners, engine control panels, dashes for service rigs, drillers panels, and sandline controls. Halls have been involved with over the rebuilding from scratch of over twenty service rigs.
-
product
Trailer Lighting System Tester
Scanner
A Scanner Trailer Lighting System Tester makes the job a lot faster and easier since it powers your trailer's lighting circuits in sequence. You check the operation of all lighting functions in a single walk-around instead of two or three.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Universal A/V Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
64 Gbaud High-performance BERT
M8040A
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
Hoist Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
product
Trailer Light Tester with Ammeter
Checkmate 1200-A
An improved version of the Checkmate 1200, this reasonably-priced tester comes equipped with a 0-to-20-amp ammeter. It's capable of testing SAE trailers or RV's with electric brakes.
-
product
Cable and Harness Tester
CHT
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
Advanced Diagnostic Trailer Tester
Alpha MUTT
Innovative Products of America
The Alpha MUTT® takes IPA's industry leading Super MUTT® platform, and adds the ability to instantly save, store, and share inspection reports. It gives customers peace of mind with complete accountability through detailed reports and gives technicians a better, faster way to enter and track report results. The mobile, durable Alpha MUTT® tests trailer lights, air brakes, and ABS systems via a Bluetooth-connected tablet with IPA's custom diagnostic software suite.
-
product
4/5 Pin Trailer Harness Checker / Towing Maintenance Kit
#8026
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
product
Connector Board for Cable and Harness Tester
CB49
Populated with solder pads to accept a suite of TE-Connectivity Micro-MaTch connectors, this board addresses markets plagued by vibration and fretting corrosion, and requiring "miniaturized connectivity". Rated to 500Vdc/350Vac, the CB49 may be used on all CableEye models. The CB49, sold without connectors, contains nine sets of 20 solder pads accommodating numerous configurations of Micro-MaTch connectors.
-
product
Guided Assembly | Cable Harness Testers
Autobuild™ Software
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections.
-
product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
product
Wire Harness Tester
NX Pro
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
product
Trailer Testers
Innovative Products of America
Quickly troubleshoot lighting, air brake and ABS systems. IPA is the world's leading manufacturer of trailer testers and fleet equipment. All of our Mobile Universal Trailer Testers (MUTT®s) are made and assembled in the USA.
