Filter Results By:
Products
Applications
Manufacturers
Trailer Harness Testers
determine that a trailer's lighting is working. Trailer
See Also: Wiring, Wiring Analyzers
-
product
LIGHT RANGER MUTT
TT9103
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
product
Trailer Light Tester
Checkmate 1200
Checkmate 1200 is a good, basic light tester for trailer light systems that can also serve double duty to power anti-lock brake systems.
-
product
Light Testers
Hall’s have designed and manufactured products for oil, industrial, farming, commercial, and transportation markets. Products such as truck and trailer light testers, bop savers, early engine warning systems, oil spinners, engine control panels, dashes for service rigs, drillers panels, and sandline controls. Halls have been involved with over the rebuilding from scratch of over twenty service rigs.
-
product
Trailer Lighting System Tester
Scanner
A Scanner Trailer Lighting System Tester makes the job a lot faster and easier since it powers your trailer's lighting circuits in sequence. You check the operation of all lighting functions in a single walk-around instead of two or three.
-
product
Trailer Light Tester with Ammeter
Checkmate 1200-A
An improved version of the Checkmate 1200, this reasonably-priced tester comes equipped with a 0-to-20-amp ammeter. It's capable of testing SAE trailers or RV's with electric brakes.
-
product
Trailer Buddy 4/5 Pin One Man Trailer Wiring Tester
220
*Tests 4 & 5 Pin Flat connector wiring *Each signal from vehicle emits a unique tone *Loud beep can be heard over shop noise *One person makes complete test in 30 seconds! *Just apply brakes, turn signals, running lights& engage reverse *Tester also emits unique tone for any shorts in the wiring! *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
product
4-Pin Trailer Light Tester
3536C
Peaceful Thriving Enterprise Co Ltd
4-pin Small Size Trailer Light Tester & Circuit Troubleshooter for US, Plug tester into vehicles 4-pin connector and operate vehicle's turn signals, lights and brakes. When there is power present, the green light will glow.
-
product
Bit Error Rate Tester - MATRIQ
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
Trailer Tester
Inspector 930
The Inspector 930 trailer tester is a complete, all-in-one trailer diagnostic system which simplifies ABS, brakes, air, lights, and electrical testing. It provides the ability for a single technician to perform a full inspection in one trip around the trailer.
-
product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
product
Wire/Cable Harness Tester
PANTHER 4HT
Qmax Test Technologies Pvt. Ltd.
The Panther 4HT Wire \ Cable Harness tester is designed for Automotive and Semiconductor industry to apply in testing of wire harnesses, that needs testing during production with whole new fleet of features that make the task reliable, complete and fast. It uses innovative technology to test the impedance values. It can be interfaced to any type of fixtures as required. It uses the Learn and Compare technique for finding out opens or shorts in a harness. The learnt open / short combination from a Good Board is taken as reference and compared with the Board Under Test for any mismatch.
-
product
Advanced Diagnostic Trailer Tester
Alpha MUTT
Innovative Products of America
The Alpha MUTT® takes IPA's industry leading Super MUTT® platform, and adds the ability to instantly save, store, and share inspection reports. It gives customers peace of mind with complete accountability through detailed reports and gives technicians a better, faster way to enter and track report results. The mobile, durable Alpha MUTT® tests trailer lights, air brakes, and ABS systems via a Bluetooth-connected tablet with IPA's custom diagnostic software suite.
-
product
PAM4 Bit Error Rate Tester.
BERT-1102
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
product
Wire Harness Tester
NX Solo
The Dynalab NX Solo Tester is an economical, feature-rich, stand-alone wire harness tester offering up to 256 test points. The powerful NX Editor software application is used to create unique program files to successfully validate all electrical and electro-mechanical wire harness parameters. This tester is compatible with all Dynalab NX accessories such as printers, scanners, control ports, and much more. The NX Solo Tester supports network communications with the NX Server for efficient file transfers and advanced data collection.
-
product
Multi Trailer Tester Jobber Pack
#TSTPK1
Innovative Products of America
4 vehicle side trailer circuit testers and a three-way adapter.Test 7 flat, 7 round, 6 round and 4/5 pin trailers and receive a 3 way trailer adapter. Troubleshoot tractor trailer circuits Allows bypassing of troubled circuitry while on the road Eliminates guesswork "Winged" grip for easy removal from electrical connectorKit Includes:#7893: 7 Flat (Spade) Pin Trailer Circuit Tester#7865L: 7 Round Pin Circuit Tester (includes one brass jumper)#8000: 3 Way Trailer Adapter (7 flat pin to 6 round pin and 4/5 pin)#7897: 6 Round Pin Trailer Circuit Tester#7866: 4/5 Pin Harness Checker
-
product
Trailer Wire Plug Tester
767943
Plug these testers into any car connector and you will have an instant test of running light circuits. Features LED display to show completed circuit for the running lights left turn signal and right turn signal. Auxiliary and electric brake circuit are included on the 6-way tester and auxiliary, electric brake and battery charge are included with the 7-way tester. One piece units with internal ground. Proper installation and set-up of a brake control, when a trailer is not readily available, is possible with the 7-way tester. Current Monitor testing device is designed to assist in determining whether a tow vehicle's 7-way blade car end connector has been wired properly. (Current Monitor is an excellent diagnostic tool for installation, setup and troubleshooting of electric trailer brake controls.) The Trailer Tester is designed to help you quickly identify problems in the wiring of the trailer. This is done by testing the Left Turn, Right Turn, Tail/Marker, Brake and Back Up circuits on the trailer. The tester indicates approximate amount of current in each circuit (i.e. trailer battery). Brake Control Bench Tester is a test device designed to determine if a brake control is working properly. Checks brake control output, independent of vehicle wiring. Simulates many fault conditions including open ground, short circuit, open load and more.
-
product
Sefelec Harness Testers
Partech Systems Australia and SEFELEC France have formed a partnership to provide a more efficient service to our Australian Customers. Our common goal is to provide our customers with a total solution to cable testing and harness testing in the manufacturing and through life support realms.
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
product
Cable Assemblies & Harnesses
High performance microwave cable assemblies and coaxial components supporting critical operations with application specific premium interconnects for high durability. Embedded with RF Florida Lab technology, our cables are available with customised option packages and are especially well-suited for precision testing applications and harsh environments in aircraft, marine, space and ground applications.
-
product
Automated Coherent Receiver Tester
CoRx Tester.
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
product
2100Vdc Screw Terminal Connector Board | Cable & Harness Tester
CB29H
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination.
-
product
CableEye Generic Surface Mount & TH Board | Cable & Harness Tester
CB51
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with solder pads to accept both aligned and staggered, 1.25mm and 1.5mm pitch, surface mount and through hole (TH) connectors, the board addresses any market with a demand for board-to-board connections. Rated to 700Vdc/500Vac, the CB51 may be used on all CableEye models.
-
product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
product
Cable Harness EM Solver
MHARNESS
Electro Magnetic Applications, Inc.
MHARNESS to Complete the Last Mile of EM Coupling Simulation Traditionally, electromagnetic effects simulation has focused on the transients induced on the overall cable bundle of complex systems. MHARNESS is a transmission line solver that reveals the EM transients on the most critical element of systems: the pin interface to electronics systems. Now, EMA3D and MHARNESS can co-simulate in one self-consistent simulation.
-
product
Mini MUTT Portable Trailer Tester
#9003A
Innovative Products of America
portable trailer tester for testing lights and electric brakes on light-duty type trailers (7 spade, 6 round, 5 and 4 pin). The Mini MUTT places a load on the trailer's electrical circuits to verify proper lighting function. The Mini MUTT is powered by an (optional) internal 12v battery,
-
product
Trailer Light & Air Brake System Tester
Express Garage
The Express Garage Trailer Air and Electrical Systems Tester is a tool that anyone with even basic air brake knowledge can look at and instantly know how to use.
-
product
3' Harness, 50-Pin Male D-Sub Connector
GT97109
3' harness, 50-pin male D-sub connector on both ends.
