-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
Test Fixture, Axial And Radial
16047A
-
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
Product
Load Cell Indicators
-
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicators within this range are encased so that the operator can either use it on the move (if battery powered) or be a permanent fixture, e.g.: wall mounted.
-
Product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
-
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Dynamic Mechanic Loading Tester
-
King Design Industrial Co., Ltd.
*Complies with IEC 61646, IEC 61215 mechanical load test specification. * Air pressure is adjustable, output range is from 2400pa to 5400pa ±5% . * Maximum measurement range: 220 x 260 cm. * Apparatus structure material：aluminum-extruded. * Fixtures and holders can be customized design for requirement of testing module. * Manual operation is simple; manual maintenance is easy.
-
Product
Receiver, G12x, 18 Module, with 20" Platform, for Slide Mount
310104385
-
The 20” G12x Receiver provides rack mounting and tabletop mounting options. The 20” platform provides a large surface for use with large fixtures and supports 180lbs. When used in conjunction with VPC slide mounts and support legs, the Receiver can support 350 lbs. The Receiver is equipped with VPC’s Quadratrack™ engagement system which provides four points of pull down for a reliable connection every time up to 20,000 cycles. The handle can be rotated in 90 degree increments.
-
Product
Compact Tester
-
Designed for testing a family of products with similar functionality. A cost-effective solution for simple PCB architecture. Measurement system integrated with the adapter. Allows the use of interchangeable adapter inserts, including tandem type. Allows you to expand the scope of functionality. Optional interchangeable adapters (fixtures). Perfect for low-volume production
-
Product
Pneumatically Powered Bed of Nails Testers
Automator Pneumatic Family
-
Designed to provide factory assembly line conveyor based pneumatically actuated full test automation. Interchangeable pneumatics and manual lever options provide operation as a fully automated tester or as a manual bench top tester. These functional interchangeable options allow this fixture to grow with you as your production volumes increase. Test plate changeover is a quick 2 minute job. 4 thumbscrews to change the bottom plate and 4 SHC screws to change the top plate. The top plate drops down and slides out with the connector assembly. The bottom plate lifts up and out. The new plates slide back in. All rear panel connectors are mounted to the aluminum bracket on the top plate. This whole top plate assembly slides out together eliminating wiring hassles. Double sided access plate sets use transfer pins to get the signals from the bottom plate up to the top plate.
-
Product
Manual Fixture Kit
230354 – CMK-05
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Standalone Bench Test System for FCT, ICT, ISP and Boundary Scan
LEON Bench
-
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
Product
Fixtures For Testing
-
Columbia offers a wide range of different fixtures and test equipment that are possible to modify according to your needs of testing. Our range of different types of test fixtures goes from ICT, RF, General Purpose, CMP to CMK.
-
Product
XCITE 1100-5 Inertial Mass Excitation System
-
The 1100-5 Inertial Mass Modal Excitation system allows the testing of structures where backup fixturing is not available or possible. Accelerating an internal mass with the closed loop hydraulic excitation system generates the inertial forces. The compression control of the Xcite Master Controller maintains a constant force over a frequency sweep by continuously altering the drive signal to maintain the required dynamic force level.
-
-
-
Product
ICT/FCT-Fixtures, Max UUT 370 × 300 mm (wxd)
CK-2 Medium (Hold Down Gate) / 230156
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
Control Module
MOC
-
The MOC is our universal control module for a wide variety of tasks, such as controlling relays in the fixture.
-
Product
Wind Power Solution
NXA SIEMENS
-
The NXA SIEMENS is custom-made with firmware and fixtures designed specifically for Siemens 2.3, 2.4, 2.6, 3.6, and 4.0. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
LCR Meter
SS10X Series
-
LCR Meters are basic passive component testing equipment, can be used in quality management department or production process for quality inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, electric valve, contactor, cable, wire, etc. This series LCR meter, offering different kind of testing fixtures, can improve testing precision and reduce the difference value of error code, being an economical and useful basic testing instrument.
-
Product
Solar Radiation Sensors
-
The solar radiation sensors that Campbell Scientific offers come in a variety of designs: pyranometers, net radiometers, quantum sensors, and pyrheliometers. These sensors measure various aspects of the energy imparted by the sun on the Earth’s surface. A leveling fixture fitted with a bubble level may be required to accurately install solar radiation sensors.
-
Product
High Temperature Component Test Fixture
16194A
-
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
Torque Gauges
-
Mark-10 torque gauges and torque testers are accurate and feature-rich torque measurement products ideal for a wide range of torque applications. All torque gauges and torque testers capture the peak torque in both directions (CW and CCW) and have selectable units of torque measurement. Torque capacities are available from 10 ozFin full scale to 5,000 lbFin, depending on the torque gauge or torque tester. Units may be handheld or used with a test stand and gripping fixtures to create a complete torque testing solution. All torque gauges and torque testers carry the CE mark.
-
Product
µHELIX® Test Probes
Series S200, S300, S400, and S500
-
Test Probes for fine-pitch applications: CSP, BGA, SiP, SoC, flex-circuits, micro pcb, sub-mm center-to-center spacing, half mm, quarter mm spacing. Excellent for use in sockets, fixtures, and contactors for semiconductor testing and in coaxial installations.
-
Product
Test Accessories
-
By combining the latest in LED technology with the unmatched illuminating dynamics of prismatic glass, this High Bay LED luminaire brings a superior, incomparable proficiency and reliability to the table. With its remote driver capability, the TDK HBLED-540 High Bay LED Light Fixture is ideal for EMC chambers with minimal RF emissions.
-
Product
Flat Flex Test Fixtures
-
Z-AXIS Flex Circuit Test Fixtures are used to connect flex circuits to test equipment. 20,000 plus cycles. Using the Z-Axis Elastomeric Connector Interposer, the connection to the OEM FFC connector becomes permanent and is thereby saved from over-use.
-
Product
Manual Fixture Kit
230355 – CMK-06
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Boundary Scan Program Development Service
-
No need for test fixtures. Integrates product development, production test, and device programming in one system. Test and Programming data can be reused in Production. Fast test procedure development. Reduced inventory management. Eliminates or reduces ICT usage time. Pre-production testing can begin as soon as prototype is released.
-
Product
Manual Fixture Kit
230356 – CMK-07
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
-
Product
Standalone Test System
1000 Series ATE
-
The Circuit Check 1000 Series ATE provides a configurable standard platform that can utilize multiple mass interconnect interfaces while providing ease of maintenance and the ability to accept a wide variety of test fixture solutions. With the 1000 Series ATE, test procedures become automatic, with test steps and go/no-go limits easily programmable.
-
Product
Power Module, 100V, 3A, 300W
N6776A
-
The Keysight N6776A is a 300 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
