-
Product
Outdoor Exposure Tester
OET
-
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
Product
Rack Systems
-
Real-time testing and validation often require versatile testing platforms, providing a high number of different signals ranging from low-power communication and sensor signals to high-power actuator signals. Integrating all the necessary components in one standard system and designing signal-conditioning for all interfaces is time-consuming and requires specific expertise.
-
Product
50 lane, 50 port, PCI Express
PEX88048
-
The new PCIe Gen 4.0 PEX88000 series from Broadcom builds on the longevity of the PEX series of switches, now spanning 12 families. The PEX88048 switch allows Data Center and Cloud Providers to build flexible, scalable rack infrastructures, along with other advantages.
-
Product
6TL22 Off-Line Testing Platform
H71002200
-
Learn about our Build to print service for Test Platforms. The 6TL22 Platform is a perfect base for the conception of a real modular Automatic Test Equipment for low to mid manufacturing volumes.A system designed around the 6TL22 is simple, easy to maintain and cost effective. The rack is prepared for the direct integration of the three platform based receivers from Virginia Panel, the S6, G12 and G12X.
-
Product
GPIB Digital Interface
Model 4863
-
ICS's 4863 GPIB Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications. OEM board versions available for inclusion in test chassis.
-
Product
Terminal High Resistance
-
Terminal High Resistance Standards that can be rack or bench mounted. The 6636 Series provides a set of customer chosen precision resistance standards enclosed in a temperature controlled chamber.
-
Product
Calipers - Digital/Electronic
-
Use a digital encoder that displays measurements on a screen instead of the rack and pinion system that analog calipers display on a round dial.
-
Product
MultiGas™ TFS™ Gas Monitor For Multi-Compound Gas Analysis
-
The MultiGas™ TFS™ Monitor is an online, multi-compound, trace gas monitoring system in a stand-alone 19-inch rack enclosure. It uses an innovative tunable filter spectroscopy technology enabling high selectivity and stability measurement. Low detection limit (sub-ppm levels for most gases) is achieved through the use of high throughput optics coupled with a long-path gas cell and a high sensitivity detector.
-
Product
RADAR Stability Testing
PN9002
-
Radar component and system testing usually evokes images of complex, expensive measurement systems occupying multiple equipment racks. In some cases, radar equipment designers have even used entire radar systems as a proving ground for their new components and modules. With the introduction of the PN9002 pulse-to-pulse radar stability test set from Noise eXtended Technologies , radar testing has become significantly less complex and costly. The modular PN9002 system provides outstanding dynamic range at frequencies from 2 to 18 GHz and optionally from 0.4 to 18 GHz.
-
Product
Flexible Pick And Place Machine With 128-feeder Capacity
MC385V1V
-
The high-precision MC385V1V Pick and Place system ensures accuracy and repeatablity with high-quality ballscrew drive, linear encoders, and full vision alignment. Programming and operation are made easy with mature, fully supported Windows-based software. Machine holds up to four 32-port feeder racks for a maximum feeder capacity of 128 tapes. Waffle trays and cut strip tape holders can be used in the placement area.
-
Product
24 Block Desktop Receiver
VGR24-RM1
-
VG Mass Interconnect products provide a common Universal interface for your custom test rack and simplifies functional test across your product line. Mass interconnect bench-top and rack mount receiver Plug and play interface blocks for signal, coax, high current, pneumatic controls, and more Stable proven products with 25 years in service Best cost of ownership Fast delivery next day on key products! Compatible to currently available test instrumentation and platformsThere are a number of different block types: Coax up to 26 GHz Power up to 150 Amps Coax and power combined Signal: up to 170 pins, @250 VAC/5 Amps Pneumatic: up to 13 fittings Vacuum: port modules High speed: USB 3.0, HDMI, RJ45
-
Product
Rack Extender Kit, 9025TR, 1.5", Special
310113769
-
Rack Extender Kit, 9025TR, 1.5", Special.Rack Mount Extender Kits are used for mounting to racks with mounting rails recessed more than 1.”NOTE: Used only with slide mounted 9025TR p/n's 310104498 & 310104477.
-
Product
VME64x 4U 84HP 8 Slots
-
Hartmann Electronic’s 8 slot 19” rack mountable VME solution – The VME64x 4U system. This VME chassis comes with two 250W cPCI hot-swap power supplies with room for up to 4 supplies and horizontally oriented card slots. This platform conforms to VITA 1.1-1997 while providing a low profile, practical packaging solution for high-performance processors.
-
Product
Switch Mode Power Rack Rectifiers
-
The Switch Mode Power Rack Rectifier is a complete modular rectifier designed as a ready-to-go system to generate high-quality DC, available in air or water cooling.
-
Product
Powered VME Crates
6U VME 195 Mini
-
The VME195 mini crate is the perfect choice for small setups with only a few VME modules. The crate offers 9 VME slots in a compact designed chassis with integrated low noise power supply and cooling fan. The mini crate can be used on the desk either as a desktop or up-right unit or be installed in a 19” rack.
-
Product
Test Of Hand Pneumatic Tools
-
The measuring system consists of a test site and a control rack. The test site is equipped with a mounting for the test tool with measuring sensors: vibration, torque and speed, as well as a pneumatic regulator, a filter and a powder type brake clutch. The maximum torque test is performed until the rotation is completely stopped. The screen displays both the directly measured maximum torque and the calculated maximum power of this sample. At the end of the test, the results are presented to the operator on the monitor screen.
-
Product
AdvancedTCA Backplanes
-
Mesh, Dual Star (5U), and 7U Pluggable Dual Star. Versions for both 19" rackmount and 23" ETSI racks are available. All Elma Electronic AdvancedTCA backplanes are compliant to the PICMG 3.0 Rev. 1.0 specifications.
-
Product
50-Watt Rack Mount Transmitter
FLS-2
-
Fiber optic cables are a critical part of modern life due to the vast amount of data they carry to support businesses, internet users, and emergency services. The cost of losing these services, even temporarily, is immeasurable. The FLS-2 system is designed to assist in locating, monitoring and providing damage prevention to these cables. The FLS-2 high-performance, high-power rack-mounted transmitter is typically mounted in a re-gen staton, customer access point, or central office. The FLS-2 transmits a locate tone on the metallic sheath of the fiber cable over vast distances to ensure the cable can be located quickly and accurately, even in congested areas.
-
Product
MAXDIO Connect
-
The MAXDIO Connect panel is a 19 inch rack mount or table top device capable of delivering Push-Pull outputs controlled by Open-Gnd Discrete or TTL Discrete.
-
Product
65 lane, 17 port, PCI Express
PEX 9765
-
Broadcom has extended the reach of PCIe for use as a fabric for data center and cloud computing through its ExpressFabric initiative and platform of hardware and software. ExpressFabric can eliminate expensive bridging devices within the rack, such as adapter cards that translate native PCIe to Ethernet and back to PCIe. Yet ExpressFabric works seamlessly with other standards used within the rack and in rack-to-rack connectivity.
-
Product
GPIB Analog Interfaces
-
ICS's GPIB to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Optional isolated Analog inputs. Available in rack mountable Miniboxes™ and OEM board versions. All of ICS's GPIB to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
Voice Monitoring
VOIP Echo
-
*The Voice Band Analyzer (VBA) is an analysis tool for monitoring the quality of voice band traffic (including hybrid echo) over VoIP, TDM and wireless networks*VBA works in conjunction with GL's TDM, Packet, and Wireless non-intrusive capture products, such as T1 and E1 Call Capture and Analysis, VoIP PacketScan&trade, and GSM, CDMA, and 3G Call Capture Products. VBA instantly detects voice file captures and with appropriately installed analysis modules, monitors speech levels, noise levels, and hybrid echo. Other analysis modules such as ITU-T P.561, P.562, P.563, fax and modem analysis, and many others can be hosted as plug-ins.*The VBA application can also operate on pre-captured files. It supports A-Law, µ-Law, 16-bit PCM (Intel), 16-bit PCM (Motorola) and MS Wave file formats.*Required software PKV100 and VBA032 at each probe location and PKV170 PacketScanWEB - Network Surveillance Software*Required hardware - 1U rack PC with sufficient hard disk for capturing over 10,000 calls (80 GB HD) for each VBA colocated with a probe*Additional hardware - PC for PKV100 PacketScan™ Software
-
Product
Rasterizers
LV7300
-
LV7300 is a 1U half rack size rasterizer. It is compact but supports eye pattern measurement up to 12G-SDI.
-
Product
Slide Kits
-
VPC offers several slide kits that are required for all VPC slide mount receivers. Slide kits are sold by length and length is decided by the depth of the individual test rack. Rack extender kits are available for certain slide kits and receivers. Please note, not all slide kit lengths are appropriate for all receivers. For more information, please consult the individual receiver user manual.
-
Product
Capacitance Sensor Systems
-
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems that connect up to 10 capacitive sensors or capacitance probes with individual analog measurement outputs. We also offer cost-effective customized capacitive sensor amplifier board and probe system for easy integration. Our inspection systems linearity exceeds 0.01% full scale measurement (FSM) and resolution to sub nanometers.
-
Product
Rack Mounted Spectrum Analyzer
-
Designed for the measurement and analysis of communications and broadcast carriers, making uplink, down- link, L-Band carriers, IF, and 10MHz reference signals easy to measure, monitor, and store.
-
Product
Contact Resistance Measurement System
CRMS
-
The CRMS is a system designed to allow any user to measure the resistance of each set of relay contacts associated with the relay under test. The test system consists of a CONTACT RESISTANCE MEASUREMENT UNIT (CRMU), a MULTIPLE RELAY TEST RACK, as well as an interconnect CABLE ASSEMBLY. Either DC or AC energy to pick and drop relay coils under test for all contact measurements is supplied from the CRMU and easily interfaces with the Multiple Relay Test Rack. For additional and more thorough testing of relays an external relay tester can be interfaced to the Multiple Relay Test Rack to supply energy to the relay coil. It is recommended that the UTE Relay Tester With Timer/Counter (UTE Product # 15967-00) be utilized so the operator can take full advantage of the unique features it offers
-
Product
G12 Slide Mount
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Product
Receiver, G12, 12 Module, Rack Mount
310104338
-
Receiver, G12, 12 Module, Fixed Rack Mount Unit 15" Platform Supports 275 lbs
-
Product
Autosamplers for Chromatography
-
Maximize the throughput and flexibility of your ACCQPrep system by adding automated sample loading for longer unattended operation.The two rack AS 2x2 and four rack AS 4x2 sampler options allow different chromatographic conditions to be applied to a variety of different samples and doubles or triples the fraction collection capabilities of the base system.The ACCQPrep AutoSamplers provide high recovery of samples with 99.9% transfer of analyte. PeakTrak software allows users to quickly create sample queues for walk up open-access labs and overnight purifications. Develop methods that result in the highest purity and largest loading capacity with the 3 Step Focused Gradient Generator that works seamlessly with the AutoSampler and PeakTrak software. An integrated wash station and sophisticated robotic probe movement ensures sample purity and limits cross contamination.
