Watch Battery
single cell battery 5-20 mm round and 1-6 mm thin.
-
-
Product
Battery Cell Simulator
BCS-LABCAR
-
The ETAS Battery Cell Simulator (BCS-LABCAR) is a Hardware-in-the-Loop system which specifically targets the signal-level test, validation, and calibration of battery management systems (BMSs). The BCS-LABCAR is a high-precision Battery Cell Simulator that emulates the behavior of individual battery cells and packs across a wide range of challenging operating conditions, e.g. cell balancing over-charging, deep discharging, or pulse operation. The system is highly modular and thus scalable to emulate battery packs from a single cell all the way up to 200 cells.
-
Product
Electric Vehicle Battery Cell Tester
MCV
-
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
Product
Battery Impedance Tester
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Battery Testing Chambers
-
We supply a variety of test chambers for testing small battery cells to large lithium ion battery packs. Battery test chambers are supplied to a variety of industries including telecommunications, computer and automotive. With the goal of reducing automobile emissions and the development of electric vehicles, the need for lithium ion battery testing is even more critical. Our proven experience provides the most cost-effective solutions. Each test chamber is built according to specific test requirements and may be interfaced with battery cyclers, control & monitoring data acquisitions systems and other test equipment for a complete integrated test solution. All environmental chambers are designed with safety in mind. A variety of safety features are provided for reliability and abuse testing of batteries. These features may be incorporated into CSZ test chambers and tailored to the various hazard levels of EUCAR (European Council for Automotive R&D), a consortium of European car manufacturers. To better assess the hazard potential of tests, EUCAR has investigated hazardous situations and divided them into eight risk classes. The development of the safety equipment of our battery test systems is also based on this classification. For each hazard level, we recommend specific safety options that can be included with your chamber to meet your specifications to safety test your product. Together with our customers, we assess which safety devices are necessary for the respective test chambers.
-
Product
Handheld Battery Powered Digital Synchro Meter
DSM-4
-
The DSM-4 is the handheld battery powered digital synchro meter with a large four digit LCD display. It is auto-ranging to accept virtually all standard military synchro signals. The DRM-4 is a handheld battery powered digital resolver meter. A dual range switch provides compatibility with all low-level resolvers ranging from 3.5V to 14V.
-
Product
Battery Pack BMS Test Equipment
WA-BMS-3NE
-
Xiamen WinAck Battery Technology Co., Ltd.
The battery BMS test system can be applied to the integrated test of 1S~100S power lithium-ionbattery pack BMS with LMU and BMCU modules, such as the BMS performance andHILL test.
-
Product
Swagelok-Type Battery Test Cell With Three-Electrode System
TBT1
-
Liquid electrolyte battery test cell with PTFE sleeve and corrosion-resistant metal components, designed for stable laboratory testing up to 10 MPa and 200°C.
-
Product
Solid-State Three-Electrode Battery Test Cell
SST1
-
Solid-state three-electrode test module with a 40 mm PEEK sleeve, adjustable ≥4 mm inner diameter, and pressure capability up to 500 MPa for advanced electrochemical analysis and battery research.
-
Product
Battery Testers
-
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
-
Product
High Current Probes (Battery Contacting) HCF34806B600G700A
1133491
-
The High Current Probes, designated HCF34806B600G700A, featuring the order code 1133491, are designed for exceptional performance in battery contacting applications. These coaxial probes are engineered to handle continuous currents of up to 100 A, providing reliable connectivity even under extreme conditions, with a temperature range spanning from -45°C to +200°C. The probes boast a compact pitch of 7.60 mm (300 mil), making them suitable for tight integration into various electronic designs.
-
Product
PXI Battery Simulator Module
41-751-001
Simulator
The 41-751 is a low power battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Non-Beryllium Solid-State Battery Spectroscopy Module
SS1
-
A customizable non-beryllium spectroscopy module for solid-state battery research, compatible with IR, FTIR, UV–Vis, XRD, and other laboratory spectroscopy systems.
-
Product
High Voltage Battery Test System
-
The increasing use of electric drive systems both in the automotive industry and in transportation requires the development of new high-performance energy storage systems. In order to support you in the development and production of these systems, S.E.A. develops individually configurable test systems which are scalable and can be used flexibly for the respective requirements.
-
Product
Automatic Batteries with Filters with Thyristors
BATLVFS600
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
High Current Probes for EV Battery Packs
High Current Probe
Up to 500Amps - customized connections - battery pack charging.
-
Product
Battery Analysis Software
-
Battery characteristics vary over time and depend very much on maintenance and the environmental conditions of the specific application. Each installation tends to have its own 'fingerprint'. Capturing and managing this critical operational data has always presented a challenge to facilities managers. Recording and analysing data using traditional pencil and paper methods is both time consuming and prone to error.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF600
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensationof power factor in low voltage instalations.
-
Product
Electrometer / High Resistance Meter, 0.01fA, Battery
B2987B
Electrometer
The B2987B Electrometer/High Resistance Meter is the world’s only graphical electrometer that allows you to confidently measure small currents with 0.01 fA (0.01 x 10-15 A) resolution and large resistances of up to 10 PΩ (10 x 1015 Ω). In addition, battery operation eliminates AC line noise from your critical measurements.
-
Product
Backup Battery Monitor And Switch
-
Renesas offers an automatic battery back-up switch, intended as a low-cost solution for the switching of systems between two power supplies; main and battery backup.
-
Product
Battery Cell Simulation / Emulation
BMS
-
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
Product
Battery Capacity Tester
BLU-A Series
-
The battery capacity test is performed to determine the health of a battery. DV Power’s battery load unit BLU-A is a portable, powerful, and lightweight solution for battery capacity measurement. It is applicable to any battery string such as lead-acid, Li-Ion, Ni-Cd, etc., with up to 500 V battery voltage. As a special feature, BLU100L model enables the capacity testing of a single Li-Ion cell.The capacity test is performed in an accurate and user-friendly way. Also, it is in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.Battery load unit BLU-A enables setting discharge currents up to 240 A, with a resolution 0,1 A. Furthermore, if higher currents are required, BLU-A units can be connected in parallel, or additional BXL load units can be used.The instrument offers the best power-to-weight ratio in the market. BLU-A models start from 12,8 kg / 28.2 lbs and deliver up to 28,4 kW of power.The user can select three discharge modes:Constant current,Constant power,Constant resistance.Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.The instrument monitors discharge parameters in real-time during the capacity test. A 4,3-inch touch screen display shows battery voltage, current, elapsed time, and capacity during the entire test. Also, BLU battery load unit can be used with DV-B Win software. As a result of that, a user can see a detailed numerical and graphical presentation of key parameters and can create reports in various formats.Testing with BLU-A doesn’t require a disconnection of the battery from the testing equipment.
-
Product
MINI Battery Discharger & Capacity Tester
IDCE-4815CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-4815CT can provide 0-150A (steps:1A) adjustable current for different test requests
-
Product
Battery String Simulator
BSS
-
AMETEK Programmable Power, Inc.
The Elgar Battery String Simulators (BSS) provide safe, reliable battery power for spacecraft testing. The broad range of features available ensures simulation capabilities for more than just two terminal power. It's the ideal solution for complete integrated system testing, not just battery elimination.
-
Product
Otii Battery Toolbox
-
Otii Battery Toolbox is a subscription-based software add-on that upgrades any Otii box to a powerful battery profiler and emulator.
-
Product
CTEK LITHIUM US Battery Charger
56-926
-
The LITHIUM US is an advanced microprocessor controlled charger specially designed to recharge and maintain the cells of Lithium-Iron (LiFePO4) batteries - maximizing their performance and lifespan. With up to 4.3A of charge current available the LITHIUM US is extremely flexible and will charge LiFePO4 batteries from 5Ah to 60Ah and maintain up to 120Ah.
-
Product
Battery Powered Telemetry Systems
-
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
Product
Stationary Battery Comprehensive Tester
SAT-AG Series
-
Shaanxi Aitelong Technology Co., Ltd
SAT-AG Series Stationary Battery Comprehensive Tester is a kind of product introduced according to the market demand, which integrates the two major functions: on-line monitoring and capacity check test, with higher integration and better functions.SAT-AG is specifically designed for the maintenance of the lead-acid battery discharge in the electricity and telecommunication sector. It is a new high-tech intelligent product that provides safe, reliable and convenient constant testing equipment for the DC system(Direct current system) users.
-
Product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
-
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
Product
Battery Tester With Printer
-
Hangzhou Xun Anda Electrical Co., Ltd.
• battery maximum capacity: 220Ah or 2000CCA(SAE)• voltage test range: 7-15VDC• operating voltage: 7-15VDC , storage battery power supplied• maximum power dissipation: 0.5W around• operating temprature: -10°C~50°C;• operating humidity: 30%~90% (without condensation)• display modes four super bright nixie tube with 0.56 inch ,four different color Led indicator light• keying: three keying total for using related operation
