Continuity
Test devices which measure shorts over a large amount of test points.
-
Product
Semiconductor
-
The semiconductor industry faces continuous pressure to reduce device size and costs while improving performance and reliability. Semiconductor, test and assembly automation manufacturers demand the same improvements from the motion technology which drives it. Haydon Kerk Pittman continues to develop new technologies in motors, lead-screws, gears, encoders, actuators, slides, drives and complete sub-systems that increase operational speeds and accuracy while lowering the cost of ownership.
-
Product
Manual PAT Testers
-
If you are looking for a manual PAT tester with a pass fail reading or a PAT tester with readings we have a solution for you. Carry out mains supply checks, IEC lead tests, Earth continuity tests at 200mA, Insulation resistance tests to 250V and 500V, and more with these popular testers. All of our manual PAT testers are available as kits to help you streamline the way you work.
-
Product
NI-5792, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782511-01
RF Adapter Module
The NI‑5792 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5792 modules.
-
Product
Oxygen Deficiency Monitor
Series 1000
-
AOI's Oxygen Deficiency Monitor is designed to provide continuous protection of personnel from oxygen deficient atmospheres. An excellent oxygen deficiency monitor for government labs, universities, research facilities, and industrial laboratories for helping to ensure the safety of breathing air.
-
Product
DC Power Supplies
-
Scientech Technologies Pvt. Ltd.
Power Supply is the most indispensable component of any electronic laboratory. A reliable, most accurate, fully specified, guaranteed and an efficient Power Supply Equipment are thus manufactured on a large scale by Scientech Technologies which has robust output protection and fault detection capabilities. DC Power Supplies with Different specifications of Voltage and Current are being manufactured for various Applications. The DC power supply converts the conventional 110 V or 220 V alternating voltage into continuous pulsating DC voltage (+3.3 V, +5 V, +12 V and -12V) used by various electronic components. A DC Power Supply also regulates the voltage to eliminate spikes and surges common in most electrical systems.
-
Product
Millimeter Wave Spectrum Analyzer
-
Insight Product Co. offers the spectrum analyzer for frequency measurements of millimeter wave generators of continuous or pulsed signals. The spectrum analyzer can be ordered to cover a complete millimeter wave frequency band: 35-53 GHz; 53-78 GHz; 78-118 GHz; or 118-178 GHz and offer exceptional spectral resolution of 1-5 kHz.
-
Product
Syringe Pump
500x
-
The 500x syringe pump provides precise, predictable flow and pressure control at flow rates from sub-microliter up to 204 mL/min. Exceptional low-flow stability at up to 5,000 psi (345 bar) makes this the ideal pump for high pressure applications from deep well core analysis to a wide range of chemical applications.analysis to a wide range of chemical applications.The SyriXus controller has backlighted keypad and 4-line LCD display, as well as built-in and optional interfaces for computer control and other devices. Programming is easy and flexible, with instant access to menu screens even when the pump is running. This allows you to change operating parameters on the fly. Control the pump remotely using driver for LabVIEW™ software, in addition to pump controller. The 500x pump module has a single-ratio drive train with auto-lubricating gears for long life and low maintenance. Special fittings are used to prevent leaks and ensure safety at maximum pressure. Wetted materials are compatible with most aqueous and organic liquids, corrosive solutions, heated fluids, liquefied gases, viscous fluids, or slurries and pastes. Hastelloy cylinders are available for chemical compatibility of corrosive solutions. Single and continuous valve packages are 100% Hastelloy for full compatibility. Trust in the Teledyne LABS SyriXus pumps for proven reliable design. Known for years of performance, it can delivery fluid or pressurized gas for long term experiments. Or hold pressure constant in the system at a simple click of the button.
-
Product
IR thermal imaging
JOHO260
-
Wuhan JOHO Technology Co., Ltd
JOHO260 is an outstanding light-weight IR thermal imaging surveillance system for helicopter, UAV, vessel, vehicle and any carriers. It is equipped with a mid-wave IR thermal camera, laser range finder for 24 hours continuous detecting and tracking air, sea and ground target via manual or auto model, it provides detection images and target relative position to control terminal.
-
Product
High-Voltage Test Device
PGK 70/2.5 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Operation as DC or Ac testing device* Polarity of the DC voltage can be easily be reserved* Robust and durable
-
Product
Surge Voltage Generator
SSG 3000
-
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
Product
Phase Shifters
-
Phase Shifters continuously change the phase of a microwave signal by applying a varying DC current, voltage or digital signal, depending upon the model type selected. Customized features are highly sought after designs, comprising a great majority of products in existence.
-
Product
Fully Automatic Tensile Testing System
-
This is a fully automatic tensile testing system for metals. The system is fully automated from supply of specimens, measurement of specimens, tensile testing, recovery of specimens, and data processing, and is capable of continuous nighttime testing.
-
Product
EMP- EMI Solutions
-
We have spread our business tentacles and are operating smoothly, through our DELHI NCR branches which are having facilities like Mechanical and Electronic Designs, Manufacturing, Integration and Testing for development and production activities. We have the In-house Environmental and EMI pre-compliance test facilities which guarantee better quality products.It is our pledge to serve the society with more efficient and qualitative output through our open mindedness and creative solutions. We continue with ardent hope that our products will definitely gather more and more momentum with the defence, the private industrial bigwigs and international companies as well. Growing the business tentacles in India, Concept Shapers are embarking upon the drive of expansion of the resources at its disposal. Our resources are our strength, be it human or the space. We firmly believe in the doctrine of ‘Engineering Innovative Concepts to configure a better tomorrow’.
-
Product
12-440V AC Multi-Function Tester
1965
-
Peaceful Thriving Enterprise Co Ltd
*Pocket clip.*Bright LED indication.*No test leads required.*Screwdriver voltage probe.*Check voltage on 12-440V AC.*With UL and RoHS Approval.*Two LR44, 1.5V batteries included.*Tests for voltage, continuity and polarity.
-
Product
DC Hipot Tester,
294
-
Our Model 294 is a simple-to-use DC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 294 DC Hipot Tester includes all the features you need to get the job done and move on. Make testing simple with common sense security settings. PLC Remote allows you to make DC Hipot Testing safer with Personal Protective Equipment (PPE).
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
Endurance® High Temperature Infrared Pyrometers
-
The Endurance® Series of infrared pyrometers features rugged and flexible instruments designed to meet the demands of harsh industrial environments and provides continuous visual process monitoring in a wide range of applications and temperatures ranging from 50 to 3200°C (122 to 5692°F).
-
Product
Point IR Gas Detector
IR400
-
The IR400 Infrared (IR) Point Detector is a hydrocarbon gas detector that continuously monitors combustible gases and vapors within the lower explosive limit (LEL) and provides alarm indication.
-
Product
Digital Multimeter
Metra 16S
-
It is Analog Digital Multimeter which measures VAC, VDC, VAC+DC, Frequency, mA DC, mA (AC+DC), Resistance, continuity, Diode, Farad, AC current measurement.
-
Product
DC Hipot Tester
296
-
Our Model 296 is a simple-to-use Hipot Tester with the built-in ability to easily test Ground Continuity (Low Current Continuity). The 296 is capable of performing Hipot Tests in both AC & DC currents. You need a Hipot Tester that includes all the features you need to get the job done, the 296 has what you're looking for Make testing simple with common sense security settings.
-
Product
IPTV Testing
-
EXFO offers IPTV test solutions to assess the network copper physical layer, validate the xDSL service and test the performance of the IPTV component at any stage of the deployment. Our Ethernet IPTV testing, IPTV analysis capabilities and advanced IPTV monitoring solutions offer complete end-to-end quality of experience (QoE) assessment for IP video. EXFO enables providers to successfully introduce video services faster and manage them more cost-effectively, by continually ensuring the highest service quality.
-
Product
Tunable CW Laser Source
IQTLS
-
The IQTLS is a continuous wave (CW) laser source combining high-power output, narrow 100kHz linewidth and 0.01pm resolution tunability. Available in single or dual laser configurations, this tunable laser source can be controlled locally via USB or Ethernet ports and is SCPI VXI-11 compliant.
-
Product
Gas Detection Controller
MX 43
-
Teledyne Gas & Flame Detection
Fully scalable, and designed to functional safety performance level 1 standards, the MX 43 is an analog and digital controller that continuously measures and controls gases in the atmosphere. The MX 43 gas detector manages both digital lines and analog channels, and covers all needs for a wide variety of gas monitoring applications. The MX 43 digital technology allows up to 32 detectors to be distributed on 8 lines for increased cost savings.
-
Product
Visual Fault Locator
STC-VFL301
-
Shanghai Stone Communication tech Co., Ltd
STC-VFL301 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network.
-
Product
Ultrasonic Flaw Detector
MFD550B
-
Based on ultrasonic principle, digital ultrasonic flaw detector MFD550B can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it show the defect clearly under the dim light and strong sunlight environment. 0-9999mm measuring range can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium ion battery module，it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways inone body, customers with different habits can operate it freely. With comprehensive performance self-checking function, it can automatically generate test reports and support for many languages. With high cost performance, it is the smart choice for the practical economic model of ultrasonic testingequipment.
-
Product
Insulation and Continuity Tester
MIT2500
-
The MIT2500 insulation and continuity tester has been designed for motor and cable testing, specialist applications and electrical testing applications, where operation voltages exceed 1000 V and higher insulation test voltages are needed. The MIT2500 offers both fixed range voltages of 50 V, 100V, 250 V, 500 V, 1000 V and 2500 V, as well as a variable range that allows any voltage between 50 V and 2500 V to be "dialled in". This is supported by the new test voltage feedback control, which maintains the output test voltage to within 2% of the selected range, even when under test.
-
Product
Digital Tesla Meter
HT208
-
Model HT208 digital teslameter is controlled by the SCM,which is suitable for handle operation.It can be used to measure DC or AC magnetic field and flux dencity.The device can be carried on one’sperson. It is characterized by its wide measuring range,simple operation and clear display. It is still added with the function of maintenance such as holding Measure Value/Peak Value,As mT or Gs unit of display can be change over,Measuring range of 200mT or 2000mT can be choosed,and others that as reseting zero by key and so on. The power is one piece of battery 9V. It can be used continually about 20 hours
-
Product
Laser Diffraction Systems
-
Since the release of the 7991 in 1974, the first commercially available particle size analyzer, Microtrac has been at the forefront of Laser Diffraction technology. By continuously improving the instrument technology, Microtrac offers customers a robust portfolio of Laser Diffraction instruments that’s ideal for particle sizing and characterization.
-
Product
Radar Detectors
-
histler''s FDSR (Field Disturbance Sensor Rejection), the most recent advancement to combat new vehicles equipped with Frequency-Modulated Continuous Wave (FMCW) K band blind spot and collision avoidance devices that clutter nearly all of K band causing a normal radar detector to alert continuously.
-
Product
Clamp Meter, Auto, True RMS, 400 A AC, 600 V AC, 600 V DC, 28 mm Jaw Opening Max.
72-7226 CAL DU
-
The 72-7226 CAL DU from Tenma is a digital clamp meter. This stable, safe and reliable digital clamp multimeter is designed with large scale integrated circuits and A/D converter as the core as well as overload protection and novel structure which make them a superb tool for electricians. It measures AC/DC voltage, AC/DC current, frequency, duty cycle, resistance, diodes and continuity and also includes data hold, sleep mode and relative mode features. The resistance measurement range from 400 ohm/4kohm/40Kohm/400Kohm/4Mohm/40Mohm (±(1%+2)), frequency measurement range from 10Hz to 10MHz (±(0.1%+3) accuracy). It is 3 3/4 digit digital clamp meter with precise operation, fashionable structure and highly reliable measuring instrument. The meter uses large scale of integrated circuit with double integrated A/D converter as its core and has full range overload protection. It complies with IEC61010, pollution degree 2, overvoltage category (CAT II 600V, CAT III 300V) and double insulation.
