Signaling
The use of signals for controlling communications. (atis.org)
See Also: Signal, Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 8-Bank 6GHz SMA
60-802-008
The 60-802-008 is a 4-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Single Channel High Voltage Linear Amplifier
F10A
The F10A is a general purpose broadband linear amplifier having a fixed amplification of 10 times and capable of bipolar high voltage output of ±100V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
product
Turnkey or PCI Cards and Software
WinCAT Systems
# True fast transient recorder system.# 4, 8 or 16 channel models.# 1 MHZ aggregate 12 bit sampling, resolution equal to 0.024% of full scale.# 13 record lengths, user selected, 132 msec to 1,320 sec in typical 1-2-5x scope progression.# 6 programmable front end gains, user selected, equal to 0.4, 1, 2, 4, 10 and 20 volts full scale.# Software converts digitized voltages to Engineering units.# Digital Triggering, Amplitude and slope, in engineering units from digitized input signals.
-
product
Coating Thickness Gauge
Meter MEGA-CHECK -Basic
The new generation of MEGA-CHECK devices first used probes in which an own microcontroller, the analog sensor signals are digitized to the device outputs. This new technique is extremely trouble-free and even allows accurate and repeatable readings. The probe cable is both sides (control unit and probe) and therefore particularly service-friendly, as if a cable breaks, the device must not be returned, but only the cable is replaced. The units are equipped with a large, clear and illuminated graphic display. A variety of Fe, ferrous and dual
-
product
Barometric Pressure Transmitter
Comptus Barometric pressure sensors utilize an integrated silicon, absolute pressure sensor with internal temperature compensation. The sensor is mounted to the signal conditioner board. A 3/16 inch diameter tube may be attached to the sensor to provide remote pressure sensing. The output of the sensor is scaled to provide the desired output signal.
-
product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786853-01
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal solution in both the lab and the production floor. The PXIe-5831 meets the stringent challenges of 5G New Radio, but it is also able to test a variety of cellular and wireless standards such as Wi-Fi 6. In addition, you can easily expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
product
PXI 10A Fault Insertion Switch 6-chan 2-bus
40-192-012
This PXI fault insertion switch uses solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test: Open-Circuit. Short-Circuit between UUT connections. Short-Circuit to external signals. Through relays on each channel enable signals to the UUT to be set open-circuit. Fault Insertion Buses allow any channel to be shorted to any other channel and also enable any channel to be connected to an external signal such as Power, Ignition or Ground to simulate fault conditions. The module is supplied with 2 fault buses.
-
product
PCI bus Test Adapter
pcibus1b
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
-
product
Digital Storage Oscilloscope
2555
The 2550 Series digital storage oscilloscopes deliver performance and value in 2-channel and 4-channel configurations. With bandwidth from 70 MHz to 300 MHz and 2 GSa/s sample rates, these oscilloscopes offer 24 kpts/Ch waveform memory, 32 automatic measurements, and advanced triggering capabilities including math functions. Engineered to allow you to see more of your signal under test, the 2550 series’ widescreen 7” TFT display offers a significantly larger viewing area than typical economy oscilloscopes (5.7”).
-
product
The Integrated Solution To GNSS + GBAS Functional Testing
GSS4150
To help developers and integrators test the airborne GNSS receiver in their GBAS landing system (GLS), Spirent has developed the GSS4150 solution. The GSS4150 is a VHF signal source generator, supporting multiple different message types, enabling you to build the solutions that power the future of aviation.
-
product
Power Quality Analyzers
Is used to measure electric power signals to determine the load's ability to function properly with that electric power.
-
product
Advanced Cable Tester v2
TP800110
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
product
PXI-2529, 128-Crosspoint, 2-Wire PXI Matrix Switch Module
778739-01
The PXI‑2529 is a high‐density PXI matrix switch module that you can configure as either a 4x32 or 8x16 2‑wire matrix by using different terminal block accessories. It uses electromechanical relays that offer excellent performance for high-power signals and low thermal offset for accurate measurements at low-voltage levels. The PXI‑2529 also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Hall Effect Sensor
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
product
Waveguide Switches
Waveguide switches are electromagnetic switches with hollow circular or rectangular cross-sections and are used for routing RF energy in microwave communications, broadcasting, and in radar applications. Waveguide switches can be used to transfer both power and communication signals, and the bandwidth of a waveguide is in relation to its size, and thus always referred to by its size (e.g. WR112, WR90, WR75 etc.). Compared to coaxial switches, waveguides can route extremely high power signals over a narrow bandwidth at low to high frequencies, and now Lightweight Waveguide series is available.
-
product
Mixed Signal Oscilloscope - 1.5 GHz, 4 Analog Plus 16 Digital Channels
MSOX4154A
1.5 GHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
product
PXI Dual SPDT RF Switch 6GHz 50 SMA Terminated
40-880-001
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
product
PXIe-5650, 1.3 GHz RF Signal Generator
781215-01
The PXIe‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Standard Optical Interleaver
An innovative technique for expanding the number of channels per fiber involves an optical device, called an optical interleaver. For example, in most DWDM equipment, the standard channel spacing is 100 GHz. But spacing the signal-carrying frequencies every 50 or even 25 GHz can double or even quadruple the number of channels per fiber. This job is accomplished by an optical interleaver. Such a device takes two multiplexed signals with 100-GHz spacing and interleaves them, creating a DWDM signal with channels spaced 50 GHz apart. The process can be repeated, creating even denser composite signals with 25-GHz or 12.5-GHz spacing. The signals at the receiving end are recovered with the same devices used as splitters or optical de-interleavers. Thus, devices and/or networks can be upgraded without requiring that all devices be upgraded, or network bandwidth can be increased.
-
product
Oscilloscopes And Digitizers
Oscilloscopes and digitizers measure changes in electrical signals over time. Use these products for time‐ and frequency‐domain applications as well as to build spectrum analyzers, transient recorders, and many-channel phenomena detection systems.
-
product
GPS/GNSS Antenna Signal Splitter 4-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS421
INSTOCK Wireless Components, Inc
GPS421 is a four way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
product
IC-INT-VPX6d, 6U VPX Dual Intel® Xeon® Single Board Computer
IC-INT-VPX6d
The IC-INT-VPX6d is a 6U OpenVPX digital signal processing (DSP) embedded computing board for defense applications. It is a key element in high -performance embedded computing (HPEC) designs.
-
product
Easy Connection Of IEPE Sensors To Voltage Input Measurement Devices
K- IEPE
Our K-IEPE module is designed to connect IEPE sensors to a voltage measurement device that normally cannot support IEPE sensors. The powered K-IEPE module simply enables IEPE sensors to be connected via the BNC terminals and will output the signal voltages to an analog measurement device.
-
product
PXIe-5624, 2 GS/s, 12-Bit PXI IF Digitizer
783132-01
The PXIe‑5624 is optimized for superheterodyne receiver architectures. It features an onboard digital downconverter, which converts IF signals to I/Q data. As a result, you can use the PXIe‑5624 either as part of a PXI Vector Signal Analyzer or as a stand-alone IF digitizer.
-
product
Oscilloscope - 200 MHz, 2 Analog Channels
DSOX3022T
200 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
product
HPx-310 Radar Signal Output Card
The HPx-310 Radar Signal Output card is a replacement for the HPx-300, form, fit, and function. It generates representative radar signals for system testing, simulation, training or radar video streaming. Under software control, the card generates radar video, trigger and azimuth signals similar to those generated by real radars.
-
product
Signal and Spectrum Analyzer
FSW
The high-performance R&S®FSW signal and spectrum analyzer was developed to meet demanding customer requirements. Offering low phase noise, wide analysis bandwidth and straightforward and intuitive operation, the analyzer makes measurements fast and easy.
-
product
Signal Evaluation Systems
*Integrated flow, temperature and wire monitoring*Adjustable switching outputs for monitoring flow and temperature*Clearly visible multi-color LED bargraph display*Signal output via potential-free relay contacts*Connection options: Insulation displacement / screw terminals and cage clamps
-
product
LXI HighDensity 224x16 2A Matrix with BIRST
60-554-027
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
product
LXI 2.4GHz 50ohm 8x8 Matrix
60-771-004
The 60-771 is a family of integrated RF matrices suitable for use up to 2.4GHz in a 50 ohm transmission line system. The matrix design permits any single Y input to be connected to any single X input, permitting the concurrent connection of 8 RF paths. All signal paths are bi-directional permitting any connection to be used as an input or an output.
