Digital Multimeters
digital display multi function measurement instrument.
See Also: Multimeters, Analog Multimeters, Bench Multimeters
-
product
PXI Programmable Resistor Module
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
-
product
The Mag Lead
136
*Mag Lead features a magnetic disconnect near the test probe end. *Just disconnect the test probe and you can “stick” to any metallic ground or test point. *Quit fumbling with alligator clips that fall off - Mag Lead’s powerfull magnet will hold tight! *This is a time saving tool - if you don’t have to walk to your tool box to retrieve your alligator clips, even on just half the occasions, then you’ve saved time. *Very helpful for automotive reference points and troubleshooting. *Can eliminate the need to hold probes while checking or monitoring a signal. *Two high power, low resistance magnets hold the probe to the lead. *Fits almost all Digital Multimeters and can be used with hand-held scopes too. *Get the Mag Lead, it stays put and won’t fall off, like alligator clips do!
-
product
VB-8054, 4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument
785037-11
4-Channel, 500 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8054 combines a four‑channel, 500 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
product
32-Ch High Voltage Relays & Multimeter
YAV90HVT
The YAV90HVT is used as an automatic CAN bus controlled floating AC/DC true RMS digital volts/milliamps meter with built-in scanner, able to work directly in appliances and industrial mains powered electric/electronic equipment.Its powerful microcontroller allows to work as a distributed device able to data acquire, compare and return high level messages, reducing test operation time.The analog output is used as a set value for the optional high voltage programmable power supply for Hipot tests up to 1500V.The board uses Tripaddle connection modules and can operate as stand alone or be mounted on a standard Virginia Panel receiver.The board includes National Instruments LabView virtual control panel and operating software for a true Plug & Play operation.
-
product
PXIe Isolated Digitizer, 2-channels, 16-bit, 256 V, 32 Msa/Ch memory
M9217A
The M9217A PXIe digitizer is a single slot, 2 isolated input channels, supporting up to 256 V and sampling rate of 20 MSa/s and 16-bit resolution.
-
product
NI-5751B, 50 MS/s, 14-Bit, 16-Channel, Kintex-7 FPGA Support, Digitizer Adapter Module for FlexRIO
784061-01
The NI‑5751B is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples 16 channels at 50 MS/s. You can use the NI‑5751B to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 24 Channels, 24 Single-Ended Inputs
DN6.442-24
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
PXIe High-Speed Digitizer/ Wideband Digital Receiver, 12-bit, 3.2 GS/s, FPGA Signal Processing
M9203A
The Keysight M9203A is a low noise, 12-bit PXIe high-speed digitizer/ wideband digital receiver with programmable on-board processing. With a wide analog bandwidth, this high-speed digitizer is ideal for applications requiring wideband signal capture and very high dynamic range. The M9203A is a dual-slot 3U PXIe 12-bit wideband digital receiver running at 3.2 GS/s, up to 2 GHz instantaneous analog bandwidth and providing a large 4 GB DDR3 acquisition memory. The M9203A features a large XilinxFPGA that can implement different functionalities depending on the selected firmware option. Dedicated functions can also be implemented on board, allowing support of various applications. Furthermore, Keysight is supporting the deployment of custom processing algorithm on this digitizer with the U5340A FPGA development kit. Integrating algorithms minimizes the need for additional circuitry and exploit the full density and speed of the digitizer.
-
product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4I.2211-X8
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
High-Speed A/D 12-Bit Digitizers
GaGe 12-bit resolution digitizer models divide the input voltage range into 4,096 different digitization levels, which improves the delectability limit by a factor of 16 over the 256 levels of an 8-bit resolution digitizer model.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.447-04
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 16 Channels, 16 Single-Ended Inputs
DN6.447-16
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
product
PXIe 14 Bit High Speed Digitizer - 400 MS/s on 2 Channels
M4X.4480-X4
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
product
AXIe High-Speed Digitizer/DAQ, 10-bit, 10 GS/s, DC to 2.5 GHz BW
M9710A
Based on the AXIe standard, the M9710A is a unique 10-bit high-speed digitizer, capturing signals from DC up to 2.5 GHz at 5 GS/s. It provides excellent measurement accuracy and high dynamic range across four phase-coherent channels within a single card. Optimized response allows few hundred picoseconds pulse analysis. Moreover, an interleaving option allows acquisition at 10 GS/s on two combined channels, keeping excellent measurement fidelity.
-
product
PCIe RazorPlus Express 16-Bit Digitizer
The GaGe RazorPlus Express CompuScope is a dual-channel 16-bit digitizer supporting A/D sampling rates up to 500 MS/s with up to 250 MHz input bandwidth.
-
product
PXIe Digitizer: 500 MSa/s, 14 bit, 200 MHz
M3102A
The M3102A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.593-08
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5912-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5933-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
NI-5731, 40 MS/s, 12-Bit, 2-Channel Digitizer Adapter Module for FlexRIO
781657-02
The NI‑5731 is a digitizer adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 40 MS/s. You can use the NI‑5731 to do real-time processing and streaming of analog data with high-performance A/D converters. The NI‑5731 also includes selectable elliptic, Bessel, and bypass hardware filters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
product
C Series Digitizer Module
The C Series Digitizer Module takes both high-speed and high-resolution time- and frequency-domain measurements. It features up to four channels that can sample at speeds up to 20 MS/s—ideal for discrete detection of signals 10 MHz and smaller for applications such as fault detection, partial discharge analysis, and acoustic measurements. The module's store-and-forward architecture allows up to 128 Mbits of measurement data to be sent back to the CompactRIO Controller and analyzed. You can use the module as part of a CompactRIO system and use the LabVIEW FPGA Module to develop an advanced trigger based on low-speed streaming for added flexibility. This digitizer includes the NI-DAQmx driver and configuration utility that simplifies configuration and measurements. NI-DAQmx supports NI programming environments and Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
PXIe Digitizer: 100 MSa/s, 14 bit, 100 MHz
M3100A
The M3100A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
product
PCIe CobraMax Express 8-Bit Digitizer
The GaGe CobraMax Express CompuScope PCIe digitizer board features 8-bit resolution with sampling rates up to 4.0 GS/s with true Effective Number of Bits (ENOB) of 7.6-bits with 10 MHz input.
-
product
2-CH 14-Bit 200 MS/s High-Speed PXI Express Digitizer
PXIe-9852
The ADLINK PXIe-9852 is a 2-CH 14-bit 200 MS/s digitizer for high frequency and wide dynamic range signals with an input frequency up to 90 MHz. The 90 MHz bandwidth analog input with 50Ω impedance is designed to receive ±0.2 V, ±2 V, or ±10 V high speed signals. With a PCI Express bus interface and ample onboard acquisition memory up to 1 GB, the PXIe-9852 easily manages simultaneous 2-CH data streaming. With high speed and high linearity 14-bit A/D converters and high stable onboard reference, the PXIe-9852 provides both high accuracy and high dynamic performance, making it ideal for applications requiring high-speed data acquisition, such as optical fiber and LIDAR testing, and video signal analysis.
-
product
VB-8012, 2-Channel, 100 MHz Bandwidth VirtualBench All-in-One Instrument
783555-05
2-Channel, 100 MHz Bandwidth VirtualBench All-in-One Instrument—The VB‑8012 combines a two‑channel, 100 MHz mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O into a single device that integrates with your PC or iPad. The VirtualBench all‑in‑one instrument is simple and convenient and results in more efficient circuit design, debugging, and validation. The included software provides an interactive way to view all your measurements on a single screen and can be updated for free with software releases over time to continually add functionality and value to your VirtualBench. VirtualBench also tightly integrates with LabVIEW software to enable programmatic control and automated test sequences.
-
product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 4 Channels, 2.5 GS/s on 8 Channels, 1.25 GS/s on 16 Channels
DN6.225-16
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5923-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
Dual Channel 180 MS/s Digitizer PXI / PXIe Card
GX2482
The GX2482 series are a high performance, dual differential channel, 16-bit digitizer offering high dynamic range and excellent SFDR. The module’s differential inputs, coupled with its low distortion makes it an ideal instrument for analyzing high performance or low level analog signals. Each channel offers 3 selectable low pass filters, a 16 bit, 180 MS/s ADC, and 64 M words of memory for each channel.
-
product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 4 Channels
M4I.4451-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 24 Channels
DN6.593-24
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
