Chambers
an enclosed isolated enviroment to perform controlled analysis.
See Also: TEM Cells, Acoustic Chambers, Altitude Chambers, Anechoic Chambers, Climate Chambers, Dust Chambers, Environmental Chambers, ESS Chambers, Humidity Chambers, Refrigerated Chambers, Reverberation Chambers, RF Chambers, Salt Spray Chambers, Sound Chambers, Temperature Chambers, Temperature Humidity Chambers, Thermal Shock Chambers, Vacuum Chambers
-
Product
Regenerative Battery Pack Test System
17040
Test System
Conforms to international standards for battery testing: IEC, ISO, UL, and GB/T, etc.Regenerative battery energy discharge (Eff. >90%, PF >0.95, I_THD <5%)Multiple voltage and current ranges for auto ranging function to provide optimum resolutionHigh accuracy current/voltage measurement (0.05%FS/0.02%FS)2ms current slew rate (-90% ~ 90%)Dynamic (current/power) driving profile simulation tests for NEDC, FUDS, HPPCTest channel parallel functionTest data analysis functionData recovery protection (after power failure)Automatic protection for error conditionBattery simulator (option)High power testing equipment- Voltage range : 80~1000V - Current range : 0~750A - Power range : 0~300kWCustomized integration functions- Integrated temperature chamber - BMS data analysis - Multi-channel voltage/temperature recording
-
Product
Probe Station
ETCP1000
-
Installation of “Hot and cool chuck” - Sellectable chuck size : 4inch, 6inch. - Temperature variation : -193°C ~ 300°C (80K ~ 573K) - Additional requirements : Vacuum chamber, LN2 tank(Bombei), microscope, CCD camera, manipulators. - EPS500 is standard model in ETCP1000 probe station.
-
Product
Xenon Lamp Weather Resistance Test Chamber
-
SN Xenon lamp test chamber adopts the Xenon ARC lamp that can simulate full sunlight spectrum to reproduce destructive light waves existing in different environments so as to provide the corresponding environment simulation and acceleration test for scientific research, product development and quality control.
-
Product
Safety Test Chamber Kit for both new and existing 8801 and 9801 testers US Army, USAF
8801HT/9801HT
-
The 8801HT retrofit safety test chamber kit is designed specifically for existing 8801-8801B and 9801B hydrostatic hose test systems in the field. It may also be ordered complete with a new 8801B or 9801B tester.
-
Product
Freezing Tester
-
Our Freezing Tester units are available in vertical or horizontal configurations are used to test the bending/flexing durability of rubber, plastics, synthetic leather, shoes, etc., under cold temperatures as low as -30°C or -70°C depending on the selected model. The test chambers can be equipped with a variety of flexing/bending fixtures made of stainless steel. These models conform to ASTM D 1790, and ASTM D1593 standards.
-
Product
Accumulation Leak Detector
LDS3000 AQ
-
LDS3000 AQ is the first leak detector to use forming gas or helium in a simple accumulation chamber. Leak detector uses cost efficient forming gas or helium for accumulation leak testing. The LDS3000 AQ is very sensitive and can detect leaks down to the 10-5 mbar∙l/s range. It will detect fluid leaks as reliably as helium vacuum leak testing, but with cost nearly at the cost of air testing. The real differentiator: The leak detector uses the cost efficient forming gas or helium for accumulation leak testing.
-
Product
Thermal Shock Chamber
-
The Thermal Shock Chamber is specially designedwith independant temperature zones to facilitatethe automatic transfer of product under testthereby simulating a temperature shock to test the reliability of the product as per military and other international standards.
-
Product
Combined Environmental Reliability Test System
VTC SERIES
-
HALT/HASS testing challenges the design, components, sub-assemblies and final assemblies of today's manufactured products. Stresses are applied through a number of conditions to set operational limits and ultimately precipitate failure in the HALT/HASS test environment. Rapid thermal change rate is one of the classic conditions that facilitate product stress.VTC Series chambers are equipped with an LN2 cooling system, with modulating valve and directed air flow to the product, provides the rapid thermal change rates required to achieve maximum product stress. Additionally, these rates are accomplished with smaller space requirements, lower audible noise, no water requirement, and lower maintenance costs than a typical refrigeration system.
-
Product
Pump, Hydrostatic Test, 10,000 psi
9901-100L
-
Hydrostatic test pump may be utilized as a standalone unit or combined with any of our reservoirs, safety test chambers, test fittings or other optional equipment to achieve a complete hydrostatic test system. with integral safety test chamber.
-
Product
Switchgear Test Systems / Circuit Breaker Testing
-
ACTAS test systems provide precise information as to the condition of the chamber and drive unit without requiring them to be opened. The sheer number of parameters to be determined, the wide variety of different types of switchgear equipment in use and the harsh environmental conditions encountered during on-site tests place extreme demands on test equipment.
-
Product
Thermal Profiler
KIC K2
-
The latest-generation mobile-friendly profiling technologyThe KIC K2 Thermal Profiler features a compact and robust design that allows it to fit through the tight, heated chambers of lead-free reflow ovens. A plug-and-play hardware and graphical user interface makes profiling both quick and easy. The profile data measured by the K2 can now be viewed on either a PC or on a mobile device using the Profile Viewer App.
-
Product
Compact EMC Test Chamber
EMC-3C
-
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
Product
Gas Filter Correlation Carbon Monoxide Analyzer
Model T300
-
The Model T300 measures low ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 14 meters. The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing extreme sensitivity. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information, is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Walk-In Test Chambers
-
HIACC Engineering & Services Pvt. Ltd.
HIACC design & assemble a wide range of walk-in/drive-in test chambers. The construction model includes Integral Welded Floors, Pre-Fabricated Modular Panel construction and Compact Walk-In chambers. The Integral welded floors is adopted for heavy-duty testing with ramp rate more than 10°C/min and is ideal for high soak period testing. This is customised as per customer’s requirement.
-
Product
Near-field Chambers
-
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.
-
Product
Dust Chamber
DUST
-
Designed specifically to meet the SAE J 575 and GM 9103 P test standards. Used throughout industries to evaluate a component's ability to function in a dust filled atmosphere.
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
Product
Rain Spray Test Environmental Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s rain spray test environmental chamber is also known as rain spray test chamber, it is used to test the water resistance for electronic and electrical products, such as solar lights, garden lights, buried lights, tunnel lights, car lights, fountain lights, the display…etc. It can also provide references for product design and quality control.
-
Product
Antenna Calibration
-
TDK Test Services offers testing to domestic and international EMC test regulations, including IEC, ISO, CISPR, and SAE. Test services are offered in our 3m semi-anechoic chamber, 3m fully-anechoic chamber, 10-meter open area test site, and our shielded conducted test chamber.
-
Product
Broadband Antenna
Vivaldi
-
The dbDIRECT Broadband Antenna features a broad frequency range of operation, high gain, small form factor and directional radiation pattern, making it highly attractive for widespread use in test and measurement of emerging wireless technology devices and radars. Contrary to conventional Vivaldi antennas limited to operating only at higher frequencies, the dbDIRECT Broadband Antenna design is optimized to operate at a frequency as low as 700 MHz up to 6 GHz. This lightweight and compact antenna design provides excellent matching over a broad frequency range.The antenna is designed to be placed in a DVTEST's portable anechoic chamber such as the dbSAFE enclosures for OTA (Over the Air) testing of DUTs. The antennas can be mounted in fixed positions to facilitate repeatable results. When used in conjunction with a rotary positioning mechanism, customers are able to detect the highest point of power sensitivity for enhanced accuracy and repeatability in measurements. In this configuration, both the antennas and DUTs can be positioned in order to facilitate the measurement.
-
Product
Multi Channel Optical Fibre Verification
-
The multi-channel optical fibre test system is used in the development and qualification of single mode optical fibres. The fibres are exposed to environmental influences in a climatic chamber in order to analyse the data on insertion loss and reflection. In addition, the current temperature in the climatic chamber is documented. Insertion loss measurement is performed with the help of an optical power meter, laser sources and optical switches. An Optical Time Domain Reflectometer (OTDR) from Exfo is used for the reflection measurements. The system was designed for the simultaneous characterization of 15 sample fibres and one reference fibre.
-
Product
Laboratory Ozone Test Chamber
CX-150
-
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Ozone Test chamber is widely used to control products quality in measuring quality control; Rubber & Plastics; automobile production; wire and cable; packing materials; instruments and meters; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research laboratories; inspection arbitration, and technical supervision departments and other rubber products.
-
Product
Temperature And Humidity Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Temperature and humidity chamber is also referred to as climatic chamber, programmable temperature humidity chamber, constant environmental test chamber, constant humidity chamber, temperature and humidity controlled cabinet etc. It Is capable of simulating the range of temperature & humidity fluctuating from an extremely low value of -70℃ & 20% R.H to an exceeding high value 150℃ & 98% R.H which products may be exposed to in the natural environment. Constant temperature&humidity testing machine can be used to measure the resistance of specimens to withstanding extremely high temperature, low temperature, constant temperature, high humidity, low humidity or various programmed combinations. Applied to all materials and product which are sensitive to temperature and humidity, such as electronics, appliances, cell phones, communications, instruments, vehicles, plastics, metals, foods, chemical products, construction materials, medical products, aerospace components etc.
-
Product
Reach-In Drosophilia Incubators
-
Canden Drosophila incubator/Drosophila growth chamber offer a comfortable and controlled environment for breeding, rearing, incubating or experimenting with various insects. The fruit fly growth Chamber/Drosophila incubator is equipped with PID controller capable of maintaining tight control over the entire temperature range.
-
Product
Temperature Humidity Vibration Combined Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Temperature Humidity Vibration Combined Test Chamber meets national standards and meets specific testing requirements. It is widely used in electrical and electronic products, automotive parts, materials, etc.
-
Product
Automotive EMC Testing
-
Having been assessed by Ford Detroit’s EMC expert, we are Australia’s only Ford (and NATA) accredited automotive EMC test laboratory. Others have tried, but none have succeeded. Ford does not accept reports from EMC labs that are not on the Ford list of accredited labs. The scope ranges from component to complete vehicle level EMC testing for Australian and overseas manufacturers. We also have a fully dedicated CISPR 25 Electronic Sub Assembly (ESA) chamber, another large CISPR 25 anechoic chamber for vehicle testing or susceptibility levels in excess of 500V/m. We possess a vast array of specific automotive EMC test equipment such as BCI’s, tri-plate’s, and striplines for susceptibility and emissions testing to meet the most stringent automotive EMC requirements. Our Australian and overseas customers use our labs because they know that our reports will be accepted and will not be questioned.
-
Product
Portable Particle Size Analyzer
LISST-Portable|XR
-
Truly portable – completely self-contained with built-in data logger, processor, rechargeable battery, and 7” color touch screen display.Particle Size Range 0.35 to 500 micronsPumped and recirculating mixing chamber that keeps large and heavy particles suspended.Shock mounted optics block that can withstand the rigors of field use.A built-in ultrasonic probe for complete sample dispersion.Touch panel allows for easy SOP programming, sample analysis and display of data without a PC.Multiple Mie models as well as Fraunhofer model available for inversion, selectable from the touch panelAll data-processing is performed on board and stored in ASCII format. No post-processing necessary.Outputs: Total volume concentration, mean size, standard deviation, optical transmission, D5, D10, D16, D25, D50 (median grain size), D60, D75, D84, D90, D95, D60/D10 (Hazen uniformity coefficient), particle surface area, silt fraction, silt volume, size distribution, battery voltage, sample notes.Based on the laser diffraction principle. Compliant with ISO-13320-1 standard.
-
Product
Optical Tweezers
PicoTweezers
-
Single or dual beam optical tweezers system based on an inverted microscope • 3D real-time video-based force measurements with sub-pN resolution • Huge free space above optical trap for all kinds of sample chambers and carriers • Manipulate and navigate trapped objects with nanometer precision • Easily extendable to fluorescence, STED, Raman spectroscopy, TIRF, or CLS.
-
Product
LED Burn-In Test
-
Burn-in system, based on LXI instrumentation, for concurrent testing of up to 80 DUTs in a climatic chamber. Devices to be tested include modern light emitting diodes and LED modules.The system consists of 2 control cabinets, each with 40 independent supply and measurement channels. Each channel can be configured individually via the operator software (current or voltage, including the relevant limit values). The software supports logging of current and voltage values for each DUT on all 80 channels with a sampling rate of <1s. Additionally, the software and system also support digital I/O channels, e. g. for controlling the climatic chamber. Inputs for connecting temperature sensors are also provided.
-
Product
Dust Test Chamber
CX-S56B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Sand and Dust Test Chamber Sand and dust test chamber is designed and manufactured in accordance with the standard requirement of IEC60529.
