Isolated Digital Input Modules
-
Product
PXI Multiplexer, Single 64-Channel, 1-Pole
40-630A-022-64/1
Multiplexer Module
The 40-630A-022-64/1 is a single 64-channel, 1-pole PXI multiplexer and is part of our series of general purpose multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI/PXIe High Voltage Multiplexer, Dual 11-Channel, 1-Pole
42-321-105-HI
Multiplexer Module
The 40-321-105-HI (PXI) and 42-321-105-HI (PXIe) are dual 11-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783156-02
Signal Module
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.442-08
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 8-Channel, 4-Pole
42-614D-008
Multiplexer Module
The 40-614D-008 (PXI) and 42-614D-008 (PXIe) 4-bank, 8-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI High Density Multiplexer, 10-Bank, 8-Channel, 2-Pole
40-615A-004
Multiplexer Module
The 40-615A-004 is a 10-bank, 8-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 11-Channel, 2-Pole
42-321-126-HI
Multiplexer Module
The 40-321-126-HI (PXI) and 42-321-126-HI (PXIe) are quad 11-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-451-TE
Multiplexer Module
The 40-785C-451-TE (PXI) and 42-785C-451-TE (PXIe) are single SP4T 50GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Optical Switching - 32:1 Multiplexer Plugin Module
65-281-315
Multiplexer Module
The 65-281-315 32:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
DC Electronic Load Module, 1U Height, 60 V, 40 A, 200W
N6792A
Load Module
The Keysight N6792A is a 200W, 1U electronic load module for the N6700 series modular mainframe.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, FC/APC Connectors, With Interlock
42-850A-014-HI
Multiplexer Module
The 40/42-850A-014-HI is a PXI/PXIe 4-channel multiplexer with FC/APC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 3GHz, 50Ω, N-Type, Terminated, Remote Mount
40-785C-563-TE
Multiplexer Module
The 40-785C-563-TE (PXI) and 42-785C-563-TE (PXIe) are triple SP6T 3GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Signal , Module, Receiver, QuadraPaddle, iCon Series, 160 Position, for crimp contacts
510160101
Receiver Module
Primary mating module 510161101. (May mate with other ITA modules, as well.)
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 3-Bank 18GHz SMA
60-801-203
Multiplexer Module
The 60-801-203 is a 6-channel, 3-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 26.5GHz, 50Ω, SMA, Remote Mount
40-784B-032-E
Multiplexer Module
The 40-784B-032-E (PXI) and 42-784B-032-E (PXIe) are dual SP6T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
Digital I/O
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
PXI 2 Amp Multiplexer, Quad 4-Channel, 2-Pole
40-635A-109
Multiplexer Module
The 40-635A-109 is a quad 4-channel, 2-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
LXI Microwave Multiplexer, SP4T, 12-Bank, 50GHz, 50Ω, SMA-2.4
60-803-712
Multiplexer Module
Our 60-803-712 is a 12 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Keysight Quad 1x4 75 Ohm 1.5 GHz Multiplexer Module for 34980A
34942A
Multiplexer Module
The Keysight 34942A RF multiplexer module for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching broadband signals. High channel isolation ensures quality dynamic range measurements with your oscilloscope, spectrum analyzer, or other instrumentation.
-
Product
PXI/PXIe High Voltage Multiplexer, Single 9-Channel, 1-Pole
40-321-104-HI
Multiplexer Module
The 40-321-104-HI (PXI) and 42-321-104-HI (PXIe) are single 9-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
PXI Dual SP6T Multiplexer 18GHz 50 SMA
40-784A-022
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI High Density MUX BRIC, 2-Chan, 80-Pole
40-570-111
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI High Density Multiplexer, 2-Bank, 40-Channel, 2-Pole
40-615A-010
Multiplexer Module
The 40-615A-010 is a 2-bank, 40-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. These feature a wide range of switching configurations and are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 67GHz, 50Ω, SMA-1.85
40-785C-472
Multiplexer Module
The 40-785C-472 (PXI) and 42-785C-472 (PXIe) are dual SP4T 67GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Single 2 Channel (M Mode) SC 50 Cons
40-855-212-M50
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
NI-9212, 8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module
782975-01
Temperature Input Module
8-Channel, 95 S/s/ch Simultaneous, ±78 mV C Series Temperature Input Module - The NI‑9212 offers channel‑to‑channel, isolated thermocouple input channels. The NI‑9212 channel‑to‑channel isolation protects channels from continuous voltages up to 250 Vrms and transient (withstand) voltages up to 1500 Vrms. You can use the NI‑9212 in a variety of applications that are not conducive for bank-isolated channels such as white goods testing, in-vehicle data logging, battery stack testing, as well as in various other noisy industrial environments.
-
Product
PXI/PXIe RF Multiplexer, Triple 4-Channel, Terminated, 8GHz, 50Ω, SMA
42-882B-003
Multiplexer Module
This multiplexer exhibits low VSWR characteristically over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensures a long service life with no wear out mechanism, making the 40/42-882B MUX ideal for ATE systems requiring frequent and fast operating RF switching.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 6GHz, 50Ω, SMA, Remote Mount
40-784B-102-E
Multiplexer Module
The 40-784B-102-E (PXI) and 42-784B-102-E (PXIe) are dual SP4T 6GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
Configurable High-Density Switch Matrix PXI Card
GX6384
Multiplexer Module
The GX6384 3U PXI multiplexer switch card provides users with the ability to switch and interface tester resources to multiple UUT connections. The card is available in three different configurations, supporting 32 x 2, 32 x 4, and 32 x6 switch configurations.
-
Product
Signal/Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/ twin female contacts & round posts
510160113
Receiver Module
This module comes fully loaded with twin female contacts & round posts (p/n's 610138200 & 610138117).iCon modules mount from the rear of the iCon/i1 receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
