Automatic Test Equipment
equipment that automatically analyzes functional or static parameters to evaluate performance. Also known as: ATE
See Also: Automatic Test Systems, ATE
-
Product
PXI 8 Slot BRIC 396x4 1-Pole (9 sub-cards)
40-562A-121-396X4
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 352x4 1-Pole (8 sub-cards)
40-562A-121-352X4
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 308x4 2-pole (7 sub-cards)
40-562A-122-308X4
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI High Density Multiplexer, 1-Bank, 128-Channel, 1-Pole
40-610A-004
-
The 40-610A-004 is a 1-bank, 128-channel, 1-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI 2A Multiplexer, 8-Bank, 8-Channel 2-Pole
40-614-004
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI 2 Amp MUX, Dual 4-Channel 4-Pole
40-635-107
-
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
Single 32x2 1-Pole High-Density PXI Matrix Module
40-520-502
-
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
ATE Support
-
For the last 30 years, Terotest has offered a range of support services, from standard maintenance and calibration to ATE updates and legacy ATE replacement solutions.We provide, repair and exchange ATE modules, fixtures, adaptors and other hardware, as well as offering full maintenance contracts to our customers.
-
Product
Ethernet/LXI hybridNETBOX 16 Bit Digitizer and AWG - 40 MS/s on 4 DAQ Channels and 4 AWG Channels
DN2.813-04
-
The hybridNETBOX DN2.80/81x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 16 bit resolution and is available with sampling rates of 40 MS/s and 125 MS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
Product
Bench/System/ATE Programmable DC Power Supply Single Or Dual Outputs, 360 To 840 Watts, With Or Without Remote Interfaces
CPX Series
-
PowerFlex design gives variable voltage and current combinations within a maximum power rangeUp to 60 volts and up to 20 amps180 watts or 420 watts maximum per outputIsolated outputs can be wired in series or parallelConstant voltage or constant current operationSettings Locking (S-Lock)PowerFlex or fixed-range operationVariable OVP tripsSelectable remote sense terminalsCompact quarter or half rack 3U case sizeIsolated analogue remote control (CPX400SA only)RS232, USB & LXI compliant LAN (P models only)GPIB Option (P models only)
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
PXI 8 Slot BRIC 240x8 1-Pole (8 sub-cards)
40-561A-121-240X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 2A Multiplexer, 8-Bank, 16-Channel 1-Pole
40-614-003
-
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
PXI 8 Slot BRIC 276x8 1-Pole Dual Analog Bus (6 sub-cards)
40-560A-121-276X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
PXI 8 Slot BRIC 10x32 1-Pole (2 sub-cards)
40-562A-121-10X32
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4 Slot BRIC 150x8 1-Pole (5 sub-cards)
40-561A-021-150X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Smart Manufacturing Solutions
-
The integration of the physical and virtual worlds and the speed of technological change are just two of the challenges facing manufacturers today. Industries undergoing a digital transformation, including IoT and the merging of IT and OT, are rapidly reshaping the manufacturing landscape. Don’t fall behind! Let our test expertise and extensive knowledge of ATEs confidently guide you through this new market reality.
-
Product
ATE For ADC Module
MS 1527
-
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
Product
Automated Test Equipment
-
ATE leveraging best-in-class features of Duotech's ARTES product, in addition to a rigorous environmental test bed. From the ground up, we custom-tailored a test bed.
-
Product
ATE Connecting Solutions
-
C.C.P. Contact Probes Co., LTD.
Customized pogo towers with high frequency capability.
-
Product
LXI High Density 320x8 2-Pole 2A Matrix With BIRST
60-555-025
-
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
Modular Power
RFP Chassis
-
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
Product
LXI High Density 50x64 2A Matrix
60-552-902
-
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
Advanced Power System - DC Power Supply, 80 V, 25 A, 2000 W
N6974A
-
The N6974A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
DC Power Module, 8V, 12.5A, 100W
N6742B
-
The Keysight N6742B is a 100 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
LXI High Density 32x64 2A Matrix
60-552-003
-
A high-density single pole LXI matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
Advanced Power System: Dynamic DC Power Supply, 80 V, 25 A, 2000 W
N7974A
-
The N7974A is designed for automated test equipment (ATE) applications where high-speed dynamic sourcing and measurement is needed.
-
Product
Advanced Power System - DC Power Supply, 40 V, 50 A, 2000 W
N6972A
-
The N6972A is designed for automated test equipment (ATE) applications where high performance is critical.
-
Product
PXI Dual 12x8 Matrix, 2 Pole Switching
40-522-022
-
Medium density PXI dual 12x8, 2-pole matrix - it is also available in reed relay formats of 2-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
