DVB-T2
Digital Video Broadcasting – Second Generation Terrestrial
-
Product
LUCID Camera SDK
LUCID Arena
-
Free software for Lucid cameras.Allows you to configure the camera as well as capture images.The following libraries are also available:- Arena C++ library- Arena C library- Arena .NET library- Arena Python library
-
Product
Low CxR
-
Is a low output capacitance solid state relay containing a GaAs LED on the light emitting side (input side) and MOS FETs on the output side. A small flat-lead package has been provided which realizes a reduction in mounting area of about 50% compared withthe PS78xx series. It is suitable for high-frequency signal control, due to its low C × R, low output capacitance, and low off-state leakage current.
-
Product
Oral Probe
OT-1
-
The OT-1 oral temperature prove for humans is re-useable and has a fast response time.• Fast reading oral use, with accuracy to 0.1°C .• Smooth ball tip. Stainless steel shaft - 3'' long, .050'' diameter. Tip diameter 1/8'', 5 foot lead length. Time constant 0.8 seconds.
-
Product
2.5 GHz, 0.9 pF, 1 MOhm Active Voltage Probe
ZS2500
-
Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit, and distort signals, at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.9 pF) to reduce circuit Loading across the entire probe/oscilloscope bandwidth. The ZS2500 is ideal for 2.5 GHz and lower oscilloscopes.
-
Product
PLC Input Modules
-
The DATEXEL DAT6000 series is a unique device designed to add analog inputs to a digital PLC with a few simple instructions. Downloaded into a standard PLC it is possible to acquire analog signals. The PLC will be able to read a 16 Bit digital input equal to the analog signal. The input, output and power supply are isolated from each other. The DAT6000 can linearize , filter and convert the input signal.The DATEXEL DAT6011 converts two voltages -50 mV to 50 mV, -100 mV to 100 mV, -500 mV to 500 mV or -1000mV to 1000mV or thermocouples K Type, J Type, S type, B type, R type, E type, T type and N type to a digital PLC.
-
Product
Needle Microprobe
MT-23/8HT
-
Fast-response 23 gauge needle probe, (needle length is 8 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
E1/Datacom Transmission Analyzer
DTA-BERT
-
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
Product
cRIO-9040, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
785624-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9040 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for … data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
NI-9207, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781068-02
Current Input Module
500 S/s, 16-Channel C Series Voltage and Current Input Module - The NI‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection.
-
Product
Portable ORP Meter
YK-23RP
-
ORP meterElectrode included,Electrode dimensions: Dia 12.5mm height, 120mmBNC connectorMeasuring range -1.999mV to +1.999mVResolution: 1mVResistance: 10MohmDC 9 volts, 1mASize: (H*W*D)mm, (205*68*30)mm
-
Product
Coating Thickness Gauge
-
Guangzhou Amittari Instruments Co.Ltd
The Basic Type Coating Thickness Gauge AC-110 Series have two types: Type C ( Integral Type ), Type CS ( Separate Type ); Suitable for automotive, paint layer coating thickness measurement; Integral Type suitable for single-hand operation, large probe with large contact surface have better stability, users can get continuous, good repetitive and precise measurements. Separate Type can provide several type probe, measure can be more flexibility. It is a kind of portable measuring instrument, it can quickly, no damage and precise coating, coating thickness measurement. Not only can be usedin the laboratory, also can be used in the engineering field. Through the use of different measuring head, but also can meet the needs of a variety of measurement. Widely used in manufacturing, metal processing industry, chemical industry, commodityinspection and testing field. Is the material protection professional.
-
Product
Thermometer Pt100 One Input
HD2307.0
-
Thermometer, Pt100 sensor with one input for probes equipped with SICRAM module, measuring range –200°C +650°C.
-
Product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s, 0 - 20mA, ±20mA) And 2 PCIe Mini Card Slots
IRU152-I
-
*RISC-based (i.MX 6UltraLite) processor 528 MHz*512MB DDR3 SDRAM onboard*8GB eMMC flash onboard*2 PCI Express Mini Card slots (Wi-Fi, 3G/4G or LoRa)*4 isolated analog input channels (16-bit, 250 kS/s, 0 - *20mA, ±20mA)*1 isolated COM port*1 isolated DIO (2-in/2-out)*Embedded Linux operating system (Yocto)*Wide operating temperature range from -40°C to +70°C*Supports LabVIEW versions later than 2016*Supports OPC UA
-
Product
Satellite ATE
MS 1123
-
Configurable Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out card level testing for satellite systems (12 different types of boards). The purpose of ATE is to provide a user-friendly environment to test the boards for their functionality, perform specific tests of each card. The card level testing facilitates troubleshooting down to a faulty signal flow path. Both hardware and software designed such a way that each Input / Output is configurable and user can dynamically script the test procedure using standard ‘C’ Language.
-
Product
Probe Card
VC20E Lab
-
*20 millimeter ceramic probe card*Optimized for DC parametric test, modeling and characterization, and single site WLR*Can be quickly installed using an interface tool into various interfaces and takes minimal storage space on the test floor*Effective operating temperature range from -65° to 200° C*Leakage as low as 5fA/V. If you require faster settling time, click here*Can be configured with up to 48 probes
-
Product
Thermometers
-
Dual DisplayRecord Mode28° to 2498°F (200° to 1370°C)Timestamped multifunction recordRelative function displaysAccepts K, J and T thermocouplesData hold
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Temperature, Humidity, CO2 Transmitter
H6020
-
The regulators are designed for online measurement of temperature (C or F), relative humidity and carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
CAT III Digital Multimeter
82600
-
Measures AC/DC voltage/current up to 600V and 10A, capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and an operating temperature range between -40° to 1000°C. Features manual or auto shutdown after 15 minutes of inactivity, protection against overload at all ranges, data hold, low battery indicator and warning alarm. Also includes a LED flashlight for low light situations. Rubber outer case adds protection against drops and a stand bracket to hold meter at viewing angle and test probe holding clips.
-
Product
AC/DC Power Supply 25 W
CFM25S480-E PL
-
AC/DC power supply with 25 W from Cincon | input ranges 90 - 264 VAC | output 48 V | operates in temperature from -30 to +70 °C | class II | encapsulated version and peak load capable
-
Product
Ordnance Release Testing Services
-
Dayton T. Brown, Inc. can help ensure that your payload is delivered accurately and reliably every time. Our team is responsible for first article, production lot, qualification, and associated testing and engineering support for mechanical and electrical armament and missile launching systems. DTB can help you develop a customized test plan that combines testing across many specifications – environmental, dynamics, EMI/EMC, structural, and non-destructive. Some of the standards that we follow include:
-
Product
On-line TOC Analyzer
TOC-4200
-
The TOC-4200 is a high-performance on-line TOC analyzer, based on the proven 680°C Catalyst-aided Combustion technology. This established technology is featured in a large installed base of Shimadzu Total Organic Carbon Analyzers throughout the world, and has been applied to a broad field of industries.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Ferrules, 1m HV, Exit Towards Pin 1
A050DF5-F-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
FieldFox C Handheld Microwave Analyzer, 10 GHz
N9915C
-
Capture elusive signals with up to 120 MHz gap-free, real-time bandwidth. Measure all four S-parameters simultaneously with 115 dB dynamic range. Make accurate spectrum analyzer measurements (± 0.3 dB) without warmup. Perform over-the-air measurements for 5G NR and LTE. Use GPS/GNSS for geolocation and timestamping.
-
Product
MULTI-FUNCTION AVIONICS TEST SET
TR-220
-
Tel-Instrument Electronics Corp.
The TR-220 provides test capability for Traffic and Collision Avoidance Systems (TCAS), Distance Measuring Equipment (DME) and Transponders (Modes A, C, and S). The TR-220 features state-of-the art design technology. Microprocessor control results in easy-to-use operation that requires minimum amounts of training. Setup menu allows storage of various test parameters to facilitate quick recall of test conditions.
-
Product
Power Factor Transducer
*(0.2%ACC.) : TDPF. *(0.5%ACC.) : TSPF
-
Kusam Electrical Industries Limited
• Dual Aux. Power 110/220V AC• High Accuracy 0.2% RO at 23 °C± 5 °C• High Dielectric Strength 2.6KV AC / Min, Between Input / Output/ Power Case• ABS Plastic Case, DIN Rail or Wall Mounting
-
Product
Pressure Comparator (System F)
Type T
-
AMETEK Sensors, Test & Calibration
Type T hydraulic comparator (System F) is a self-contained high volume pressure source capable of producing pressure up to 15 000 psi. It is ideal for testing gauges and setting hydraulic relief valves and pressure switches. Multiple models are available for hydraulic oil, water, or both.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-01
Signal Module
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
DC/AC Inverter 3000 W
ODS-3000-7154-T
-
DC/AC inverter with 3000 W from Premium | input ranges from 25.2 - 45 VDC | output at 230 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
Product
Field Probe for Electric & Magnetic Field Measurement
WP400-3
-
Wavecontrol presents a new and unique field probe for the measurement of electric and magnetic fields that integrates both E & H sensors within dimensions of only 3 cm². Which makes it unique is that Wavecontrol has managed to add an E field sensor in a basic structure of a classical 3 cm² field probe. It has been possible, therefore, to obtain a 3 cm² field probe without compromising the capability of assessing E and H fields of its 100 cm² big sister, the recognized and successful WP400.
