-
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, .025" Round Post
610138115
Primary mating contact 610138200. (May mate with other Receiver contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2 ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body (RCV) – BeCu (Twin Female)BeCu/PhBrz (Crimp)Male (ITA) – BrassContact Plating Female (RCV) – 50µ” Au over 100µ” NiMale (ITA) – 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 0.24
-
product
Heavy Duty Ranger Mutt
TT9102
Commercial trailer light and electric brakes tester that reduces guesswork and saves time by powering each trailer electrical circuit in 7-way round pin arrangements. Allows for proper verification of wiring configuration, ground integrity, short circuit and overload conditions, along with electric brake operation and turn signal simulation.
-
product
Hyperspectral Image Processing Software for THz Imaging Data
ImageLab
ImageLab is a one-of-a-kind image processing tool developed by our partner EPINA for the analysis of data from various spectroscopic imaging techniques such as THz, optical, UV/VIS, IR, Raman, or mass spectrometry. Based on multivariate statistical methods it enables the user to analyze and classify acquired hyperspectral images, to merge them with maps of physical properties and to overlay them with conventional high-resolution color photos. Visualization of the image data and highlighting of analytical information round up the software package to an indispensable instrument for in-depth analysis of spectroscopic image data. ImageLab is now part of Menlo Systems’ imaging extension TERA Image. Ask us for possibilities to upgrade your THz imaging system with our unique software tool!
-
product
Continuity of Insulation Tester (Low Voltage Method)
DYQ-005
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-5;Inspection standard: JB/T4279.12-2008Used to test the film continuity (namely the pinhole number of enamelled wire sample per unit length) of enameled round wires with nominal conductor diameter of0.050mmand below;The application of advanced SCM control allows for faster operation and stronger anti-interference capacity.
-
product
Shielded and Unshielded Cable
Teledyne Marine Cable Solutions
Shielding Types• Braided I Served I Spiral• Foil & Hybrid• Vapor Barriers• Copper & Alloys• Conductive & Static Dissipative Tapes• Conductive Fabrics• Tensile Members• RFI & EMI Tapes & Braids (Serveor Interwoven)• Utilizing Flat & Round Copper• Stainless Steel• Bronze• Aramid Fibers & Textile, amongothersConstruction• Multi-conductor, shielded pairs, pairs with steel tubed fiber or copper conductors with fiber optics, coaxial conductors & aramid strength fibers
-
product
SWaP-C Single LRU HD EO/IR Imaging
Star SAFIRE® 380-HDc
The Star SAFIRE® 380-HDc delivers unparalleled stabilized HD multi-spectral imaging in a compact, low-profile package. It’s designed to maximize ground clearance in rotary aircraft without sacrificing capability and performance. Low power demand of 225W and lighter weight of only 65 pounds (29.5 kg) round out the incomparable SWaP-C advantages. This system also provides 2x-4x greater magnification than other lightweight systems in its class.
-
product
Single Phase Round Energy Meter Test Bench Type KP-S1000-C
Bofa Instrument & Equipment Co., Ltd
Single phase round energy meter test bench, type KP-S1000-C, is a special calibration equipment for testing Round (ANSI Socket type) energy meter and normal energy meter with bottom terminal block. It is an ideal testing equipment for energy meter factory or R&D institute, especially for testing ANSI Socket type energy meters. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
product
Color Matching Booth
GSM Round Cutter is used to test material grams per square meter. It would cut sample to 100cm2 cutter, depth max 5mm. Normally, GSM cutter is suitable to cut textile fabric, leather, paper and etc. It has four double-sided blades, and the blade is evenly distributed in four equal parts. The blade can be replaced. GSM Testing is essential for some tests like Matindale abraison test meet standard ISO20344.
-
product
Signal Module, ITA, QuadraPaddle, 90 Series, 192 Position, Fully Loaded with Round Posts (610 138 115)
510151107
Used together with QP ITA module p/n 510109316 for PCB mounting. NOTE: Mounting screws for this module are included with module part # 510109316. Primary mating module 510150115. (May mate with other Receiver modules, as well.)
-
product
Miniature Fluxgate Magnetometer
WFG-120
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
product
Contour Check Round & Edge
Laser measuring systems are of central importance for rolling mills to check the contours of steel profile for defects during the production process. A slight deformation on the surface of the profiles reduces the quality of the product, and in the worst case, a broken roll can even destroy the entire batch. With our systems Contour Check Round & Edge you identify and evaluate deviations at an early stage. Increase the process efficiency of your production - regardless of temperature and profile shape.
-
product
Hall Effect Measurement system
HMS-3300
Magnetic flux density : 0.55Tesla (+/-0.03T)Gap distance between both round magnets : 26mm / Round magnet diameter : 50mmMeasurable temp : RT ~ 300℃(model# HT55T3). Resolution : 0.1℃(Model# HT55T5 : RT ~ 500℃)Both HT55T3 and HT55T5 are only capable of using with HMS-3000 main body.(Not compatible with HMS-5000 )- You can flow purge gas into small chamber and measure hall effect at the same time. Gas control valve can be installed as an option.
-
product
High-Temperature Extensometers < 600 °C Capacitive
Instron® High-Temperature Extensometers are perfect for testing advanced composites, metals, polymers and other materials at elevated temperatures. This series incorporates a capacitive sensor that does not require any cooling. The extensometers come standard with a sensor conditioner unit providing a 0-10 V output with exceptionally low noise. These extensometers can be attached to round and flat specimens to perform tensile, compression, and cyclic tests.
-
product
Measuring Devices For Drawing Rings And Punches For 2-part Can Production
RINGMASTER - The Benchmark For Accuracy
Optik Elektronik Gerätetechnik GmbH
High-precision, non-contact measurement of inside and outside diameter, roundness (inside and outside) and concentricity of drawing rings for 2-piece can production. The Ringmaster sets standards in measuring accuracy, user friendliness and reliability and is therefore used in can factories on all continents.
-
product
Hot sticks
HS-120R 1.8M
Standard Electric Works Co., Ltd
● Weight : Approx. 1.1kg● The Hot Stick is rated at 100kV per 300mm (5 minutes)● High quality fiber glass round tube filled with Polyurethane.● Meets IEC60855
-
product
6-way Round Pin Vehicle side Circuit Tester
7897
Innovative Products of America
The 6-way Round Pin Trailer Circuit Tester tests trailer circuits on older light to medium duty trucks and RVs. Plug the 6 pole trailer tester into the back of the vehicle and apply the Brake Lights, Turn Signals, Running Lights etc.
-
product
H.V. Probes
PD-28
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with digital multitester.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
product
Edge Radius Measurement
EDGEINSPECT
NOVACAMTM EDGEINSPECTTM system is a modular, non-contact 3D metrology system that:Measures, down to the micron, any type of edge: cutting edges, inside or outside edges, edges on round holes, straight edges, etc.
-
product
H.V. Probes
PD-20S
Standard Electric Works Co., Ltd
● Measures both AC and DC voltages with oscilloscopes.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.
-
product
7-way Round Pin Vehicle side Circuit Tester
7865L
Innovative Products of America
The 7-Way Round Pin Tractor Trailer Circuit Tester does "one man testing" for male and female 7-way round pin tractor trailer plugs -- and much more! Troubleshoots tractor trailer circuits. One person can test all the lighting alone.
-
product
RF Flexible Cable Assemblies
Industry leader in manufacturing excellence, tailored performance, and rapid delivery of custom cable assemblies. The Flexible version, our Mini-Flex, has an FEP jacket, round braid and inner spiral shields and is available in 2 diameters, .105" &.165". The Semi-Rigid cables are available with a copper or aluminum jacket and available with a selection of different platings and 4 different diameters (.047", .085", .141" & .250"). The Conformable®, or hand formable (BJ - Braided Jacket), has a tin filled braid with a metal foil underlay and is also available in the same diameters as the Semi-Rigid type . All 3 types (Semi-Rigid, Conformable & Mini-Flex) are manufactured using the same type dielectric core and have virtually the same electrical performance. The decision of which cable to use should be primarily based upon your application.
-
product
Advanced Hydraulic Wedge Action Grips
2742 and 2743 Series
The Instron advanced hydraulic wedge action grips deliver controlled, constant gripping force using an external hydraulic supply across static and dynamic testing. They support capacities up to 600 kN (static) and 500 kN (dynamic), with interchangeable jaw faces for round or flat specimens. The design ensures jaw face positions remain fixed during gripping (eliminating preload), compensates for changes in specimen thickness, and is ideally suited for use with metals, composites, and plastics.
-
product
Taber® Linear Abraser (230V/115V, 50/60Hz)
5750
Whatever your product, be it curved, round, big or small, the Linear Abraser from Taber® can test it all.
-
product
Static Friction Coefficient Tester
JMY-16
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008; Inspection standard: JB/T4279.16-2008Used to detect static friction coefficient (μs) of enameled round wires with nominal conductor diameter ranging from 0.050mm to 1.600mm;The application of high-end SCM control allows for high sensitivity and excellent repeatability.Four-digit LED would automatically display static friction coefficient (μs) of sample;
-
product
Signal/Micro Power/ Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Position, loaded w/ twin female contacts & round posts
510160113
This module comes fully loaded with twin female contacts & round posts (p/n's 610138200 & 610138117).iCon modules mount from the rear of the iCon/i1 receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables
ELCOLEVEL - Software For 3D-straightness Measurement
Optik Elektronik Gerätetechnik GmbH
ELCOLEVEL is a software with interfaces to electronic autocollimators and inclination levels of different manufactureres. This allows for example the 3D-Straightness measurement (twist-, roll- and yaw-angle) of slides in one and the same measuring procedure.
-
product
Semi-Automatic Tablet Tester
P-Series
The versatile P-series laboratory testers offer you the latest technology, a space-saving design, and maximum flexibility. Adapt the basic units (P3-P5) to your requirements at any time.The P5 version tests all five measured variables automatically. The VibrALIGN and Roto system make it easy to position tablets precisely.The intuitive touch display enables quick and easy operation. The measurements results are shown directly on the clearly arranged display, and can be printed out or exported as PDF reports.The LAB.line design also offers many practical advantages: the generous radii, rounded corners and smooth surfaces allow easy and hygienic cleaning. The sturdy hood provides protection against environmental influences during measurements.
-
product
Laser Diameter Measuring Instrument
RC-078
The RC-078 Laser Diameter Instrument is a high accuracy one without contacting designed on the basis of the laser scan measuring principle. The 2-dimension measuring mode is applied to the instrument, and the 2-way laser beam is in the positive cross design in the measuring field, thus effectively eliminating testing errors caused by work piece shocks. It is special suitable for real-time measurement of the production field, and widely used in the test of round wire materials such as communication cables, optical cables, co-axial cables and power cables, and the test of various kinds of other round work piece diameters.
-
product
PRO Waterproof pH & Temperature Tester
pH55
The Milwaukee Waterproof pH55 PRO pH/Temp. Tester is one of our most accurate cost effective, well rounded, rugged and reliable testers in the market featuring dual level LCD readouts, easily replaceable probe and extended pH ranges to meet almost any application. It's simple 1 or 2 point automatic calibration is simple-to-use and offers TWO sets of memorized buffers to select. Ideal for use in aquariums, hydroponics, horticulture, education, pools, beer and many other applications.
-
product
Optical Measurement
• Vertical optical measuring machine for static and dynamic measurement of various elements on small cylindrical parts.• The parts can be mounted between two centres or held in place using various accessories.• Attractive design and robust construction with many new features: New touch screen control panel for easy operation directly at the workplace, bi-telecentric optical system, high resolution CMOS camera, precision sliding headstock with integrated and protected daily standard, quick and easy accessory changing system, integrated temperature sensors, dynamic LED indicator of the general status of the measured part (GO/NG) and operator messages. Equipped with an exclusive optics tilting system.• Machines specially designed to measure threads such as, parallel, trapezoidal, conical, round, square, conical, worms, ball screws, bone screws, dental implants, etc.• Reflex SCAN+ concept for measuring parts without prior programming at the touch of a button• Delivered complete with a PC and the Reflex SCAN+ software, which allows a multitude of elements to be measured easily and intuitively.
