Filter Results By:
Products
Applications
Manufacturers
ASTM
ASTM International is a globally recognized leader in the development and delivery of voluntary consensus standards, over 12,000.
See Also: E84
-
product
Franklin Tester
Model FT1
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
product
Fatigue Failure Tester
EKT-2002FF
EKT-2002FF Flexing Fatigue Tester is designed in accordance with ASTM D4482 to test the fatigue life under a tensile strain cycle on different kinds of vulcanized rubber compound to determine the fatigue life at various extension ratios.
-
product
Automatic Tag Closed Flash Point Tester
LD-LACF-A10
Automatic Tag Closed Flash Point TesterLD-LACF-A10is a highly automated machine with -50°C lowest flash point and simple operations. Used to determine flash point of liquids with viscosity below 5.5 cSt (mm2/s) at 40°C (104°F) or below 9.5 cSt (mm2/s) at 25°C (77°F) and flash point below 93°C (200°F) . Test method is complied with ASTM D56 international standard.
-
product
Photo Detector Testing
With the rise of 5G technology and popularization mobile devices, more and more advanced photoelectric sensors are used in our daily lives. In order to be better applied to mobile devices, the photosensitive area of these advanced photodetector is getting smaller and smaller. However, these applications place higher and higher requirements on the light sensing performance of advanced photodetectors. In the process of shrinking the photosensitive area, it also brings the challenge of accurate measurement of quantum efficiency. Enlitech adopts the spatial light homogenizing technology and follows the ASTM standard “Irradiance Mode” test method, which is proven that it can accurately perform quantum efficiency and other key parameter measurements of advanced photodetectors.
-
product
Fully Automatic Open Cup Flash Point Tester
K613
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to determine the flash point of petroleum products by Cleveland open cup.Conforms to GB/T 3536, GB/T 267 and ASTM D92.Microprocessor technology. Big screen LCD display. High automation, including auto-heating, auto igniting, auto-testing and auto-printing etc.
-
product
SSG Series Strain Gauge Extensometers
Shimadzu’s SSG series of strain gauge extensometers are compliant with ISO, JIS, and ASTM tensile test standards, including those for plastics and metallic materials These lightweight, precision extensometers feature a wide elongation measurement range, while retaining the flexibility to measure using small gauge lengths, and support both rod and flat plate shaped specimens. Consisting of an elongation sensor and amplifier, this extensometer is suitable for use with metals and hard plastic materials, and is fastened securely to specimens with screws. Calibration using an extensometer calibrator allows the extensometer to meet JIS and ISO Class 0.5 and ASTM Class C standards for higher accuracy.
-
product
Composite Salt Spray Test Chamber
YWX/Q-010X
Composite Salt Spray Test Chamber stimulate the actual natural conditions to do accelerated corrosion test, all the testing are based on common states on the natural environmental: such as combine with salt spray, hot air drying, humidity, low temperature and so on. The test samples are widely used on the intense changes in the environment, like automobile parts, aviation equipment, building materials, coating, electric and electrical machinery so on. YWX/Q-150X series is full compliance with ASTM D4728I, EC 60068-2-1, IEC 60068-2-14 and EIA/JEDEC JESD22-110-B standard requirements etc.
-
product
Drop Test Machine
Guangdong ALI Testing Equipment Co,. Ltd
Drop Test Machine -drop tester Satisfy With ASTM , ISTA Industrial Standards,Drop height: up to 2000mm (adjustable).
-
product
Rockwell Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ Semi-automatic intelligent Digital Rockwell Hardness tester, you can automatically test the Rockwell hardness and surface Rockwell hardness measurement；◆ Automatic variable load, automatic loading, automatic unloading, automatic conversion, automatic measurement；◆ Friendly human-computer interaction，5.2“colorful LCD screen direct display test force,loading time,conversion value and indenter type etc； ◆ Automatically calculate and display the measured value, the maximum value, the minimum value, the average value and the hardness value deviation, the display shows the resolution 0.1HR；◆ There are functions such as hardness upper and lower limit settings, tolerance alarms, data graph analysis, average and (single point) batch measurement modes；◆ Software compensation function, the machine can be ± 3HR software compensation, no need to open the top cover for mechanical adjustment;◆ With automatic hardness conversion function, according to ASTM E140 conversion, no need to check the complex hardness of the table；◆ Multi-language features, can switch Chinese, English, German, Portuguese, Turkish, Czech, Korean and other languages；◆ Built-in 2000 single data storage function and 1000 group packet data storage function, can view a single data and data analysis；◆ Optional Bluetooth wireless printer to print the measurement data, no need to manually record and write test data；◆ Optional Softhard data analysis software and Bluetooth receiver on the test data for the computer into and analysis；◆ Support FexQMS measurement of large data analysis and control software to enhance the whole plant process control, reduce material loss.
-
product
Flexural Test Methods For Plastics: ASTM D790
Resin materials (plastics) are found in a wide variety of items used on a daily basis. Recently, plastics have started to be used as structural materials in transportation equipment, such as automobiles and aircraft, due to their strength and light-weight nature. In these applications, it is important to understand the mechanical strength properties of these plastics.
-
product
Biodiesel In Diesel Analyzer
InfraCal 2 ATR-B
The InfraCal 2 Biodiesel Blend Analyzer for measuring percent biodiesel in diesel is the ideal solution where a quick, accurate, on-site measurement is required and a single, repetitive biodiesel blend analysis is needed. The InfraCal 2 ATR-B is based on proven IR technology, originally developed by Wilks, and used by fuel distributors, blenders, producers and regulatory agencies worldwide. The compact, easy-to-use Biodiesel Blend Analyzer has a measurement range of 0 – 100% biodiesel in diesel. These results are comparable to both ASTM D7371 and EN 14078, laboratory methods that require expensive FTIR Spectrometers.
-
product
Haze Meter
DRKWGT-2S
Shandong Drick Instruments Co., Ltd.
DRKWGT2S transmittance / haze analyzer is a computerized automatic measuring instrument which is designed based on the People's Republic of China national standard GB241080 "transparent plastic light transmittance and haze test methods" and the American Society for testing and materials standard ASTM D100361 (1997) Standard Test Method for Haze and Luminous Transmittance of Transparent Plastice." It could apply to all transparent, translucent parallel plane sampler (plastic plates, sheets, plastic film,sheet glass) of light transmittance, transmission haze and reflectivity test also applies to liquid samples (water, beverage, pharmaceutical, colored liquid, grease) turbidity measurements in defense research and production workers and peasants to have a wide range of applications.
-
product
AWS Probes For Ultrasonic Weld Seam Testing (ASTM)
SONOSCAN R
The robust ultrasonic probes with BNC connector allow a fast scanning over comparatively large areas with high precision and repeatability. Both our own and third-party wedges can be attached to our probes. . Thanks to the different types of wedges various material tests can be performed.
-
product
Oil In Water/Soil Analyzer
InfraCal 2 TRANS-SP
The InfraCal 2 TRANS-SP is recommended for measuring oil in water, TPH in soil or FOG in wastewater concentration levels using the traditional EPA methods 413.2 and 418.1 or ASTM method D7066-04 and Freon-113, hydrocarbon-free grade of perchloroethylene, AK-225, S-316 or other spectroscopic infrared transparent solvent as the extracting solvent. Since the extract is deposited into a 10 mm quartz cuvette cell with Teflon stopper, light end volatile components are retained for measurement. Accurate down to 0.1 ppm.
-
product
Waterproof Tester by Parameter
PTTestr 35
Ideal for quick and accurate pH checks in pools and spas, aquariums and hydroponics operations, or anywhere frequent pH testing is required. pHTestr 30 meets requirements for many standard environmental and ASTM test methods
-
product
Metallic Pendulum Impact Testing Machine
JB-S Series
Jinan Testing Equipment IE Corporation
JB-S series superior metallic pendulum impact testing system is strictly designed according to international standards ISO148, ASTM E23 and EN10045. The pendulum impact testing system is mainly used to determine the anti-impact capability of metal materials under dynamic load and is capable of doing a large number of of impact tests continuously. Adopting the important intelligent programmable logic controller (PLC) system, the pendulum impact testing system can realize the test process control and test data collection based on computer software program or digital display touch screen controller. The test data can be used for further data analysis, storage and printing. An aluminum shield with transparent tempered glass covers the load frame for safe operation. The impact testing machine of metallic pendulum is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
product
Mini-Dial Durometer
Model H1000
The Rex H-1000 Mini- Dial Durometer is both compact and easy to use. Its small dial face and included leather clip-on carrying case make it easy for an inspector to carry the gauge- for work around the shop, or out in the field. The H-1000 durometer holds the maximum reading until reset by pressing the button at the top of the gauge. The max-hold feature and small dial size make the H-1000 a good choice for hard to reach places, or for out of sight testing. Available ASTM Types: A, D, B, C, DO, E, and O.
-
product
Probes
Hygro-i Series
The Tramex Hygro-i ® relative humidity probe is the most advanced, resilient and reusable RH probe on the market today. Used in conjuntion with Tramex CMEX II and MRH III moisture meters, the Hygro-i ® relative humidity probes allow the user to perform in situ and hood type RH testing to comply with ASTM F2170 and British Standards BS 8201, 8203, 5325 for the Flooring Industry, and is ideal for use by Flood & Water Damage Restoration and Indoor Air Quality professionals.
-
product
Physical Testing
Testing is confidential and can be conducted according to the client's specifications, or such Standards as MIL-202, 331, 750, 810 and 883, as well as GSA, ASTM, ISTA, BIFMA, ANSI, industry and government.
-
product
UV Testing Machine
Dongguan Kejian Instrument Co., Ltd.
1. Meet ISO,ASTM, DIN,JIS,SAE,BS,ANSI,GM,U.S.GOVT(ASTMG153,ASTMG154,,ASTMD4329,ASTMD4977,ASTMD4587,SAEJ2020,ISO4892)2. QUV condensation device simulates the effect of humidity of outdoor,meeting 100% humidity.3. Electronic-eye irradiance control system4. Use blackboard temperature sensor providing precise temperature and recuring test result.5. Perform humidifying, condensation and water spraying circulating test.6. Irradiance is calibrated by CR-10 calibrator and automatic calebration procedure.(Paten technology)7. Specimen size and quantity: 75mm×300mm 24pcs, 75mm×150mm 48pcs
-
product
Water Separability Tester
K677
Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to determine the water separability of petroleum and synthetic fluids.Conforms to GB/T 7605, GB/T 7305 and ASTM D1401.
-
product
ESD Packaging Test Kit
PRF-911PT
The PRF-911 Concentric Ring is to be attached to the PRS-801B Resistance System included in this Packaging Test Kit. This system will also give you surface resistivity by multiplying the surface resistance measurement in ohms by 10 to obtain surface resistivity in ohms/square. The PRF-911PT meets requirements from ANSI/ESD STM11.11, ANSI/ESD STM11.12 snd IEC 61340-2-3. It will also approximate surface and volume resistivity measurements per ASTM D-257.
-
product
Auto Water Vapour Permeability Tester
TESTEX Testing Equipment Systems Ltd.
Auto Water Vapour Permeability Tester, to determine the water vapour permeability of various textile and garment fabric, coating fabric, composite, sportswear and industrial fabrics. Auto Water Vapour Permeability Tester complies with ASTM E96, ISO8096, BS 3424, etc.
-
product
Apparent / Bulk Density Tester
Bulk Density Tester Series
The Apparent Density Tester - Bulk Density Tester series testers are used to measure apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. There are three methods according to ASTM D 1895 that are applicable to various forms of these materials that are commonly encountered - from powders and granules to large flakes and cut fibers. The apparatus consists of a measuring cup which is polished inside and a funnel.
-
product
Directional Source
BAS003
The BAS003 Source is designed to generate homogeneous sound fields using random noise in compliance with the following standards: Building acoustics (insertion loss, acoustic absorption area, etc: ISO 140-3, ASTM E90, ISO 140-5, ASTM E966). The BAS003 is typically used to generate a noise in a free-field for the evaluation of the transmission loss index of a façade. The available high-efficiency power amplifier, BAS002, is light and can be remotely controlled for easy use in the field.
-
product
Corrosion Inhibitor Evaluation
ASTM G202
Metals Samples provides solutions to study the performance of corrosion inhibitors in the laboratory. The Rotating Cage is helpful in selecting corrosion inhibitors for use in oil and gas production pipelines and facilities, transmission pipelines, as well as in oil refineries. It simulates aggressive field flow conditions that cause localized pitting corrosion in a simple laboratory setup. The precision, i.e., repeatability and reproducibility, of the rotating cage has been established (ASTM G202).
-
product
Ross Miles Foam Analyzer
RMFA
Our Ross Miles Foam Analyzer – RMFA is the world's first instrument for automatic measurements of foamability and foam stability in accordance with ASTM D 1173.
-
product
Averaging Clip-on Extensometer
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
product
Load Cell Indicator
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
product
Thermogravimetric Analyzer
TGA801
The TGA801 is the latest generation of automated macro thermogravimetric analyzers to enter our lineup. The TGA801 maintains the core capabilities and reliability of previous generations of LECO macro TGA instruments, while providing key improvements in performance and robustness. By incorporating state-of-the-art hardware with an on-board touch-screen software platform and a rugged design, the TGA801 provides accurate, high-precision thermogravimetric constituent analysis—moisture, ash, volatile content, and LOI in various organic, inorganic, and synthetic materials. Complying with ASTM standardized methods, the TGA801 is applicable to many industries and applications including coal, cement, catalyst, foods, and feeds.
