Filter Results By:
Products
Applications
Manufacturers
BNC
-
-
product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8 KIT
This K-AN8 (8 analog + 4 digital input) kit contains everything needed to get the K-AN8 set up and tested on a work bench.To help with connecting sensors to the analog and digital ports the K-BoB enables easy connection with BNC connectors.Influx K-Cal is easily connected via the Kvaser LeafLight interface and Kvaser T-CANnector. (Using the Kvaser T-CANnector to power up the K-AN8 (at the desk) and terminate the CAN bus).
-
product
75 Ohm BNC to BNC Cable Assembly
40-977-701-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
BNC (F) To Minigator Test Clips
2631
BNC (f) to minigator test clips. Converts BNC (male) cables / connectors to minigator test clips for test versatility. BNC connector is molded directly to the wire for pull strength durability and dust and moisture resistance.
-
product
Cable Assembly, Receiver, 20", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
540297010147
Cable Assembly, Receiver, 20", Micro Power and Micro Coax, 4 BNC Plugs and 4 SMB Plugs
-
-
product
Low Inductance BNC Cable, VOLT:DC 60V
PX0105A
The Keysight PX0105A is suitable for narrow current pulse measurement down to 10 μs pulse width. It supports the Keysight M9602/03A.
-
product
Probes, Cables & Detectors
Probe has a mica window that has a thickness of 1.8 to 2.0 mg/cm2. This allows detection of alpha radiation as low as 3.0 MeV when in close proximity to the window. Beta radiation in excess of 35 keV and X-ray or gamma radiation greater than 6 keV can also be deteched. The detector is provided with a BNC connector. It can be used with most count rate and survey meters which accept Geiger Mueller (GM) detectors operating at 900V DC.
-
product
pHTestr® 10 Waterproof BNC Pocket pH Tester
Simply choose the electrode best suited for your application, connect the pHTestr BNC 10, calibrate, and measure. Change electrodes to suit your application without having to purchase another meter. Order electrodes separately. Large display and tactile keypad allow for easy calibration along with USA and NIST auto-buffer recognition. Hold function freezes reading on the display for easy recording. Additional features include Valox® sensor housing, self-diagnostic error messages, a battery-life indicator, and an auto-off function to maximize battery life.
-
product
LXI Single 24x8 Video Matrix, SMB (50R)
60-711-711
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75Ω with the option of SMB or MCX connectors or, with a larger case size, BNC connectors.
-
product
75 Ohm BNC to BNC Cable Assembly
40-977-701-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
50 Ohm BNC to SMA Adaptor Assembly
40-978-511-0.25m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
8" Cable
CONW1553-1
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
product
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse
T3CP500-5
500A, 5 MHz CURRENT PROBE, BNC, AC/DC, 500A rms, 750A Peak Pulse.
-
product
Step Attenuators
A stepped attenuator from Pasternack. Our BNC attenuator is a RF step attenuator design. This 50 Ohm manual step attenuator is precision manufactured to RF and microwave industry specifications.
-
product
All-In-One Toner & Probe Kit
MT-7068
The MT-7068 All-in-one Toner & probe Kit lets you use Toner and Probe to validate and troubleshoot wiring on RJ11/RJ45 cables and connectors, USB, F, BNC, and RCA connectors, and it also supplied with alligator clips to work with. The MT-7068 Toner detects telephone and Ethernet service, indicates polarity and active line numbers on voice circuits, and indicates active pair number on Ethernet circuits. The MT-7068 Toner and Probe also provide standard functions such as visual and audible signal strength indication, analog toning/detection, and continuity testing. It is ideal for all maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling , etc.
-
-
product
Audio Cable Tester
CBT-500
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
product
Low Noise Differential Preamplifiers
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
product
BNC (M) To Multi-Stacking Banana Plugs
3957
BNC (m) to multi-stacking banana plugs. Converts BNC (Female) cables/connectors to top/side stackable banana plugs for test versatility. BNC connector and banana plugs are molded directly to the wire for pull strength durability anddust/moisture resistance.
-
-
product
Magnetic Shielding Cabinet for EMI Testing
SDR-2000B
Cabinet Shell 2mm galvanized cold-rolled steel sheetCabinet Door 0.9*1.7m(L*W) 0.6*0.6mCabinet Window 0.3*0.3*0.025m(L*W*T) with 4mm hole N/APower Supply Filter 30A/220V 30A/220VInternet Line Filter RJ-45 N/ACabinet Inside Decoration PVC ceiling, PVC plastic steel wall, 10mm wooden + 2mm galvanized steel sheet floorCabinet Inside Size 2*1.2*1.8m 0.8*0.8*0.8mAfter Packing Size 2.2*2.3*2.3m 1*1.1*1.2mAfter Packing Weight 800kg 200kgWorking With EMI-9KA/EMI-9KB EMI-9KA/EMI-9KB, PC, Testing load, and operator inside Testing load is inside to connect with EMI-9KA/EMI-9KB via BNC
-
product
50 Ohm SMB to BNC Adaptor Assembly
40-978-501-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
Network Analyzer, Tester, RJ45/BNC, LED
72-9940
The 72-9940 is a RJ45 Cable Tester with LED meter display. The tester easily tests RJ45 and BNC network cables. It features remote testing which allows to test cables that are terminated at separate locations.
-
product
50 Ohm SMB to BNC Adaptor Assembly
40-978-501-0.5m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
RF Power Monitors
Standard connectors: RF In / Out - N-Female, UHF optional. Sampling Ports - RCA-Female, BNC optional.
-
product
Quad SD-HD-3G SDI Multiviewer
DigiLink DLC910
The DLC910 adds full featured 4-Channel SD-HD-3G SDI multiviewer capabilities to the DigiLink media transport platform. Consuming a single slot in any DigiLink chassis, the DLC910 seamlessly integrates into the platform enabling users to monitor the status of up to 4 independent SD, HD, and 3G-SDI video and audio channels. A full featured multiviewer, the DLC910 includes format auto sense, audio monitoring with visual activity detectors, 16 character labels per quadrant, automatic aspect ratio, and quad or full screen displays. Wide options for inputs and outputs are available using external BNCs, optical or HDMI SFPs, or other modules in a chassis using DigiLink’s innovative integrated routing capabilities.
-
product
DC-to-60MHz 1:10 Oscilloscope Probe Kit (HP-9060 Or HP-3060)
PRB-HP-9060
Up to 60MHz, Includes a handy storage pouch and includes an IC test-hook adapter for the probe., The BNC connector rotates to avoid cable tangle or kink., Cable length is 1.4 meters.
-
product
LXI Single 24x8 Video Matrix, SMB (75R)
60-711-001
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75 Ohm with the option of SMB or MCX connectors or, with a larger case size, BNC connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems. Software configuration allows the 60-711 to be set as a dual 24 by 8 matrix, a single 48 by 8 matrix and other configurations.
-
product
75 Ohm BNC Connectors
Pasternack 75 Ohm BNC connector category contains many part numbers, most are RoHS and REACH compliant. 75 Ohm BNC connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Pasternack 75 Ohm BNC connectors are built to precise RF and microwave industry specifications. 75 Ohm BNC connector are available in male or female gender with 75 Ohm impedance. BNC 75 Ohm connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm BNC connector designs include clamp/solder, compression, crimp/solder or solder attachment methods. We offer 75 Ohm BNC connector with standard or high performance levels constructed with brass or stainless steel bodies. Like the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm BNC connector group is in-stock. In addition to being in stock, these BNC 75 Ohm connectors will ship the same day as they are purchased.
