Filter Results By:
Products
Applications
Manufacturers
-
product
Battery Management Systems Testing
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
product
Balancing Software Module
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Balancing of long and disk-shaped rotors in one or two planes*Up to six correction methods (depending on software version)*Automatic operation by rotary speed detection*Display of measuring results as polar graphic and numbers*Very simple installation and operation*User guidance by clear text instructions*Extremely compact - VM-BAL fits into a small carrying case*Versatile instrument at an economic price*Available as kit including all necessary hardware and software: - VM-BAL Kit One for one plane -VM-BAL Kit Two for two planes
-
product
40 Amp Intelligent Power Management
IPMDS40
- Intelligent Power Management System- 9 - 20 Amp Single Outlets- Automatic Single Phase Load Balancing- Automatic Load Shedding based on priority rating- 40 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
product
Vibration Analysis and Balancing Tools
PRÜFTECHNIK Condition Monitoring GmbH
Predictive maintenance tools for vibration analysis can help prevent machine failure and avoid costly production downtime. Our vibration analysis tools are used for condition monitoring on rotating equipment to help detect early component wear and damage. Vibration analysis and balancing are integral parts of any condition-based and predictive maintenance program.
-
product
Signal Analysis
Synchronous Accumulation (Order Analysis)
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
product
Purpose Built Network Packet Brokers
Garland Technology’s Purpose Built Network Packet Brokers (NPBs) are devices that provide access to network traffic from multiple links, helping to centralize and improve efficiencies by sharing packets between the monitoring and security appliances. Additional NPB features include filtering, aggregating, regenerating, and load balancing.
-
product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
Deadweight Testers & Gauges
The most accurate instrument available for the measurement of pressure above a few psig is the Hydraulic Deadweight Gauge. This type of gauge operates on the principle of balancing a known mass against the force exerted by an unknown pressure on a piston of known area. When an exact balance is achieved, the unknown pressure "P" is equal to the mass "M" of the weights divided by the area "A" of the piston, according to the formula "P" = "M" / "A". In us, weights are removed or added from the piston's table, as with a double-pan balance until the piston "floats" without net vertical movement.
-
product
Transformer Ratio Meters / TRM-101
TRM-101
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Produces the 3-ph or 2-ph standard power with stable voltage and phase. Fully automatic: No manual balancing
-
product
Production Spin Testing & Balancing Services
Test Devices provides production spin testing and balancing services of production parts for customers with a repetitive need and who demand schedule predictability along with a quick turn-around time. Whether proof testing critical rotating components before shipment, pre-spinning to achieve required rotational growth prior to finish machining or simplifying the supply chain by consolidating pre-spin with rough machining and/or NDT inspection, Test Devices offers a full range of spin testing solutions.
-
product
Transformer Ratio Meters / TRM-11
TRM-11
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Fully automatic: No manual balancing. Automatic measure transformer group. Automatic calculation of ratio error.
-
product
Autocompute LCR-Q Meter Sorter
Model 4912 / 4912PR
- Microprocessor based Fully Automatic L, C, R, Q and D measurement- Autoranging with Direct Digital Readout- 4 Terminal Measurement Technique- No Tuning or Balancing- Series or Parallel Equivalent Measurement- Absolute Value and Nominal Value with Percentage Tolerance- Single / Multiple Parameters Check During Component Sorting- Feather Touch Keys with Audio Feedback- Thermal Shut Down for Overheat Protection- Special Mechanism for Fast and Easy Insertion and Removal of Test Component- Low Cost and Portable- Component Sorting on Absolute or Nominal Value Basis with a Percentage Tolerance- Aplab Model 4912PR is Remote Programmable Auto Compute LCR-Q Meter Sorter, Which can be Programmed through GPIB, RS232 or SPIB Interface
-
product
Bridge Trainer
Salicon Bridge Trainer to measure unknown Resistance/Capacitance by balancing two legs of a Bridge Circuit. With the of DC Source, Student can set the null point by using different combinations of variable Resistors Circuit Diagram is provided on-board for Teaching/Training.
-
product
DC Fault Tester
HBD-81
The HBD-81 DC Portable DC System Ground Fault Locator designed for DC fault testing. This equipment utilizes the principle of DC current differential detection and incorporates fast FFT (Fast Fourier Transform) technology for detailed analysis of the amplitude-frequency characteristics of the test signal. By balancing the safety and sensitivity aspects of DC ground fault locating, it effectively resolves the conflict between the two.
-
product
Air Flow Meter
DBM 620
The newly redesigned DBM 620 Air Flow Meter is a multipurpose electronic air balancing instrument primarily used for efficiently taking direct air volume readings from air vents.
-
product
PC Based Rotor Tester
GTS 1000
The PC Based Rotor tester is the most reliable, fast and cost-effective way to detect faults in the Rotors in less than 10 seconds. This Rotor Tester can Test Large sized Rotors of any Size, Length & Weight that can be mounted on a Load balancing machine or a Lathe and rotated at a speed of 600 rpm.
-
product
BMS Tester
MS-159
This equipment used for F/W writing, Calibration and function test. It inspect current, voltage protection mode, consumption current and cell balancing measurement to check the state of BMS and applied to the full inspection and mass production.
-
product
3U OpenVPX™ Intel® Xeon® SBC with One Smart Function Module Slot
68INT4
The 68INT4 is a 3U OpenVPX Intel® Xeon® Processor E3-1505L v6 based embedded Single Board Computer with integrated output graphics/video & I/O expansion. Balancing high-performance with relatively low-power dissipation, the processor supports up to four processing cores operating at up to 2.2 GHz. One I/O expansion module slot is provided that can be fitted/configured with any one of the 70+ NAI smart I/O and communications function modules. Ideally suited for rugged Mil-Aero applications, the 68INT4 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
Measuring Solar Fields
ISET Sensor
The solar radiation sensor is characterized by a simple and compact but precise structure. Use in balancing monitoring systems for simple, fast and reliable information about the functioning and solar "energy yield" of a PV plant. For site surveys, monitoring and other fields of survey technology.
-
product
Automotive Products
Renesas has invested in key technologies to address the current mega trends within the automotive market such as environment, safety, information, and affordability. This effort has resulted in leadership positions in high-performance power conversions, state-of-the-art precision analog, cell balancing and battery charging ICs, power-efficient Class D audio amplifiers, and highly flexible TFT display controllers.
-
product
Battery Testing
Electric vehicles (EVs) rely on batteries as their primary source of energy storage. As battery packs require battery management systems (BMS) to operate safely and reliably, it is vital to test control algorithms for state of charge (SoC) estimation or cell balancing at an early stage.
-
product
Temperature Data Logger
DL001
Record temperature in a wide range of applications including HVAC testing and balancing, transportation, and energy management with the Model DL001 Temperature Data Logger. Temperature logger has an on-board thermistor and an external sensor channel for remote temperature measurements
-
product
Scienlab BMS Environment
SL101XA Series
A BMS assumes important safety, control, and regulation functions. Those functions include monitoring parameters such as voltage, current, temperature, and state of charge (SOC). A BMS also regulates thermal management, energy management, cell balancing, and performance.
-
product
Trillium Protocol Software
Our proven Trillium Protocol Software is an extensive offering that spans from the access network to the core. We also address value-added applications that enable the optimization of bandwidth and maximize the life of networks, such as monitoring, ID catchers, lawful intercept, and load balancing.
-
product
Alnor Micromanometer
AXD610
The Alnor® Micromanometer AXD610 is an easy to use, handheld digital micromanometer for fast, accurate and reliable pressure measurement. It can also calculate velocity when used with a pitot tube. Ideal applications include HVAC commissioning and troubleshooting, testing and balancing, Pitot tube duct traverses, static pressure measurements and differential pressure measurements.
-
product
Instrument Transformer Comparator
PMT20010
Power Measurement Technologies Inc.
The PMT20010 Comparator is an automatically balancing bridge that measures the accuracy of instrumentation potential and current transformers.
-
product
Condition Monitoring
Falcon
The ultimate portable vibration data collector and analyzer. With a wide range of optional features available, the FALCON can be configured to perform balancing, run up coast down, frequency analysis and more.
-
product
Battery Front Ends
Renesas provides a comprehensive lineup of battery front ends to cover all battery management system protection, monitoring, and balancing requirements.
-
product
Field Balancing Software
DS-0227A
The trouble of rotation machinery is caused most frequently by unbalanced phenomenon of rotating shaft. However, balancing correction on-site is not easy because the conventional vector calculation method with drawing needs quite some time.
-
product
Rotor Balancing System
For the purpose of rotating parts balancing in manufacturing scale, it is necessary to conduct measurements with the minimum possible participation of the operator. The Rotor balancing system is intended for measurements related to rotating parts balancing in automated mode.
