Filter Results By:
Products
Applications
Manufacturers
-
product
Low Noise Dual Band VCO
This custom oscillator subassembly consists of two low noise oscillators covering 1.5 to 2.5 GHz, a power combiner, a standard Teledyne RF & Microwave amplifier, and a lowpass microstrip filter. Teledyne RF & Microwave designed both oscillators for low phase noise and linear tuning. The output frequency bands are switched using standard TTL control.
-
product
Silicon Detectors
Through the photovoltaic effect, detectors provide a means of transforming light energy to an electrical current. The root of the theory behind this phenomenon is a small energy gap between the valence and conduction bands of the detector. When light, with enough energy to excite an electron from the valence to the conduction band, is incident upon the detector, the resulting accumulation of charge leads to a flow of current in an external circuit. Since light is not the only source of energy that can excite an electron, detectors will have some amount of current that is not representative of incident light. For example, fluctuations in thermal energy can easily be mistaken for light intensity changes. A variety of these "non-light" contributions are present and, when summed up, make up the total noise within the detector.
-
product
Airborne Receivers & Bit Synchronizers
The Lumistar LS-28-DRSM Series Multi-Mode Multi-Band Receiver/Combiner/TM Processing Unit is designed using ruggedized packaging to survive severe airborne conditions. The LS-28-DRSM is available in several configurations: 1) Airborne receiver only (RF to bits), 2) Airborne bit synchronizer only, 3) RF to TM Processing and Display (RF to bits to UDP decom to LAN Client Displays). Models with receivers are available in any band form 200 MHz to 7 GHz with S, lower L and C bands as standards. Other RF bands are available, please consult the factory for details. This unit can be mated with other Lumistar products to provide a complete air-to-ground re-transmission system.
-
product
Millimeter Wave Amplifiers
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
product
Leakage Current Clamp Tester
M-1141
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency(fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
product
Leakage Current Clamp Tester with Bluetooth
M-1141XR
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Waveform display is possible with connection to a smartphone・Measurement data is to be accumulated in the server, and it is available for graph and CSV output・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency (fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
product
Universal Band Decoder
Bandmaster IV
Using USB (RS232) or band data (BCD) information, the Bandmaster IV converts that frequency/band data to allow meaningful automated control of your station that incorporates Array Solutions / Hamation devices.
-
product
RF Shielded Box
LTL D7001
LTL D7001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL D7001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
product
2200-Channel GSM Channelizer wih Quad A/D - 6U VPX
Model 58663
- Complete GSM channelizer with analog IF interface- Eight 180 MHz 16-bit A/Ds- Four banks of 375 DDCs for upper GSM band- Four banks of 175 DDCs for lower GSM band- PCI Express (Gen. 1 & 2) interface up to x4- LVPECL clock/sync bus for multiboard synchronization- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
10 dB V-Band Waveguide Directional Coupler for Test Labs
SWD-5038531040H-15-SB
ModelSWD-5038531040H-15-SB is a V band, three-port waveguide directional coupler that delivers a 10 dB nominal coupling level and 30dB minimum directivity across the full waveguide band from 50to 85GHz. The three-port coupler uses a traditional multi-holeand split block design to achieve a flat coupling level, high directivity, and low insertion loss. The interfaces of the coupler are WR-15waveguides with UG-385/Uflanges. Custom coupling levels are available under different model numbers.
-
product
ICE 3000 Series
ICE3001
This subsystem is an agile filter for the SATCOM frequency band, capable of acting as either a receive or a transmit filter. It enables simultaneous operation of multiple transceivers in extreme cosite environments. The ICE3001 provides multiple poles of RF selectivity to reduce broadband noise, harmonics, and spurious signals for either receive or transmit applications. This filter is a highly integrated design incorporating complete Built-in-Test capability. The design has been qualified for military applications. A dual-mount tray is also available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE3001.
-
product
3 Wire (Analogue) Earth Resistance Tester
ST-1505
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● The timer operates automatically for about three to five minutes when the “PUSH BUTTON SWITCH” and “TIMER ON BUTTON” are pressed together. ● This will keep test “ON” for the duration of the timer.● Battery check function.● Calibration performed with supplied test leads.
-
product
Low Pass and Bandpass SMA Coaxial Filters
Fairview Microwave’s bandpass filters were developed for use in various applications including GPS, ISM, RFID and Wi-Fi systems and operate in several bands, some as low as 824 MHz and some as high as 5.875 GHz. Fairview’s low pass filters allow for tailoring of a test setup for a specific application and support upper band edges of 100, 225, 400, 1000, 2000 and 3000 MHz. All of these bandpass filters and low pass filters feature female SMA connectors.
-
product
ESR(EPR) Measurement System for Magnetic Property
esr05002061101-07
This system is for the magnetic materials, especially the best for the research such as Spintoronics and Quantum dots technology. ･ It has the measurement sensitivity more than that of standard type X band ESR system, because it uses ferromagnetic resonance(FMR) .
-
product
ISM, LoRa And LPWAN Antennas
These state of the art antenna solutions operate in the ISM (Industrial, Scientific and Medical), LoRa (Long Range), and LPWAN (Low Power Wide Area Network) frequency bands, enabling secure data transmission for Industrial IoT applications.
-
product
VHF/UHF Digital RF WATT/VSWR Meter
PMR 3030
The PMR 3030 EXT Power Meter is a very versatile instrument covering communication bands from 30-1000 MHz. (The PMR 3030 is available for 30-500 MHz only. The PMR Power Meter is capable of measuring forward and reflected power in the range of a few milliwatts up to 500 Watts. The internal operating system controls measurement, display and the I/Os allowing serial communication to PC, USB to memory stick and USB Serial communication. The I/O options are used to write plots to either memory sticks or to a connected PC, the I/Os can also be used to operate the instrument, giving commands and receiving data. For documentation reference the instrument has a real time clock. Multilayer menus are used to setup and control the operation of parameters.
-
product
C-Band Red/Blue-Band Pass MWDM
WD1515/R, WD1515/B
Hangzhou Huatai Optic Tech. Co., Ltd.
WD1515/R, WD1515/B is based on mature thin film filtering tech, with wide bandwidth, flatness, low insertion loss and high isolation. It is mainly applied to the combination and separation of C-Band, Red-Band (1547~1563nm) and Blue-Band (1528~1543nm).
-
product
DC Blocking L-Band Splitter Combiner
PD5940
INSTOCK Wireless Components, Inc
PD5940 is an IP67 outdoor, weather resistant, DC blocking, four way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5940 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 4 way power divider input rating tables for additional power handling info.
-
product
Heavy Duty Pressure Transducers
PX3 Series
Honeywell Industrial Automation
Honeywell is pleased to announce its efficient, affordable and durable PX3 Series Heavy Duty Pressure Transducers, designed primarily for system pressure monitoring in HVAC, refrigeration, air compressor, pump and valve systems. Key features and benefits include: Delivers high efficiency: Proven, 1.0% FSS tight Total Error Band accuracy promotes system efficiency and lower energy costs. Great customer value: Economical choice for design/implementation; extremely flexible with multiple configuration possibilities with the right combination of features and broad media compatibility. Durability promotes system uptime: For enhanced performance in tough environments to support overall system quality, reliability and warranty. Fast availability: Short lead times on samples and production parts.
-
product
160MHz Test System
IQxel-MW 7G
Platform solution for 802.11 a/b/g/n/ 802.11ac, 802.11ax, and 802.11be testing in the 2.4 and 5 GHz and 6 GHz bands and the most popular wireless connectivity standards (Bluetooth®, Bluetooth® 5, Bluetooth® 5.1, Bluetooth® 5.2, Zigbee, Z-Wave) as well as LPWAN technologies (Sigfox, LoRa).
-
product
Active Components
MUD frequency doublers featuring Millitech technology are balanced resistive-mode multipliers covering full waveguide bands. Power flatness for a given input power level for these units is typically ± 2.0 dB across the band.
-
product
Wireless Bridge Device
BR-300AN
BR-300AN is a wireless bridge device which can easily convert a 10/100/1000BASE-T wired LAN device to a wireless LAN device. It supports a wireless LAN communication in the 2.4GHz and 5GHz bands and enables a wired LAN device to join in a wireless LAN environment easily. It also supports enterprise security which allows you to use the Wireless Bridge BR-300AN reliably even in environments such as offices and healthcare sites which require security. This product is not available in North America.
-
product
Analogue (1kV below) Insulation Tester
2132 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test. ● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
product
Infrared Camera
TI-240
Shenzhen Calibeur Industries Co., Ltd..
Detector Type: Focal Plane Array, Uncooled MicrobolometerPixel Resolution: 160x120Spectral Band: 8~14μmField Of View: 14°x11°/0.5mSpatial Resolution: 5mradThermal Sensitivity(Netd): ≤50mk@30Focusing: Manual Focus (0.3m~∞)Maximum Frame Rate: 15HzLCD: 2.5′ LCDTemperature Ranges: -20℃~+300℃Accuracy: ±2℃ Or ±2%Temperature Measurement Mode: Real Time Temperature Display, User Defined Points Or Areas of InterestRadiance Correction: 0.01-1.0
-
product
Straight Waveguide Section
Straight sections are used to make connections between components in waveguide systems. Lengths and combinations are available on special order. VSWR is better than 1.1 over the full waveguide frequency band. Precision flanges on special order.
-
product
Spectroradiometer
SpectroCAL MKII
Cambridge Research Systems Ltd
High-performance spectroradiometer with NIST traceable calibration makes extremely accurate colorimetric measurements over the entire visible spectrum, even of narrow band sources.
-
product
Analogue (1kV below) Insulation Tester
8031 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on “low ohms” : 2Ω & 20Ω.● AC voltmeter with linear scale up to 600 Vac.● 200mA short circuit current for continuity.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display of external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Supplied with high quality test leads.● BS 16 edition.
-
product
Broadband Amplifier
BBA300
The R&S®BBA300 broadband amplifiers are a new generation of highly compact solid-state broadband amplifiers designed for high availability. They feature extremely wide, continuous frequency bands extending up into the high microwave range, along with high linearity, outstanding noise power density and excellent harmonic characteristics. They also boast high system configuration and operational settings flexibility.
-
product
RF Components
Passive RF components from MegaPhase cover a wide range of frequencies, power levels and applications. MegaPhase offers a variety of directional couplers, power dividers/combiners and quad hybrids in narrow band and ultra-broadband designs ranging from 0.5 MHz to 46 GHz. The in house engineering team brings decades of experience and knowledge designing and manufacturing RF components for military, commercial and space applications.
-
product
Gated Short Wave Infrared Camera System
LIVAR® M506
The LIVAR M506 Gated SWIR Camera System is ideal for covert operations and target identification, supporting lasers from 1.0 1.6 m. Cost-effective, compact and lightweight, this range-gated, two-dimensional imaging camera operates in the eye-safe Short Wave Infrared (SWIR) band, provides day and night coverage, and supports mounted and dismounted operations. The camera system includes the camera, High Voltage Power Supply (HVPS) and Thermoelectric Cooler Controller (TECC). An optional high-PRF version is available that allows the use of low-power, high-PRF diode lasers with the camera in accumulation mode.
