Filter Results By:
Products
Applications
Manufacturers
Butterworth Filters
Refine signal, providing the flattest possible frequency in the passband, with a monotonic response.
See Also: Bessel Filters
- Frequency Devices Inc.
product
Low-Pass Filters
Is a filter that passes signals with a frequency lower than a selected cutoff frequency and attenuates signals with frequencies higher than the cutoff frequency. The exact frequency response of the filter depends on the filter design.
-
product
NI-5783, 40 MHz Bandwidth Transceiver Adapter Module for FlexRIO
784364-02
The NI‑5783 has DC‑coupled inputs with two variants: an elliptic filter variant optimized for frequency-domain applications and a Butterworth filter variant optimized for time-domain applications. The NI‑5783 is particularly well suited for applications in software defined radio, electronic warfare, high-performance machine control, and medical imaging. The NI‑5783 is compatible only with the PXI FPGA Module for FlexRIO modules that have a Kintex‑7 FPGA and the stand-alone Controller for FlexRIO.
-
product
Analog Filter
SIM965
Stanford Research Systems, Inc.
The SIM965 Analog Filter is ideal for signal conditioning applications where Bessel or Butterworth filters are needed. Bessel filters offer clean step response (negligible overshoot) and linear phase response, while Butterworth filters provide excellent pass-band flatness with some overshoot
-
product
NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module
786999-01
6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.
-
product
Filtered Analog Input Expansion Board
MSXB 048
The MSXB 048 Filtered Analog Input Expansion Board has a four-pole low-pass Butterworth filter on each of its 16 single-ended channels. For DAP applications that require analog filters to take out all above-Nyquist frequencies before signal conversion, it simply replaces the MSXB 037 Analog Input Expansion board. Signal inputs normally connect to the MSXB 048 through a panel-mount DB-37 connector.
-
product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-02
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
product
NI-9252, ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786783-01
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
product
NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module
786999-02
6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.
-
product
NI-5783, 40 MHz Bandwidth Transceiver Adapter Module for FlexRIO
784364-01
The NI‑5783 has DC‑coupled inputs with two variants: an elliptic filter variant optimized for frequency-domain applications and a Butterworth filter variant optimized for time-domain applications. The NI‑5783 is particularly well suited for applications in software defined radio, electronic warfare, high-performance machine control, and medical imaging. The NI‑5783 is compatible only with the PXI FPGA Module for FlexRIO modules that have a Kintex‑7 FPGA and the stand-alone Controller for FlexRIO.
-
product
Filter Building Blocks
Analog Devices offers an extensive line of continuous time and clock tunable (switched capacitor) filter building blocks. These devices were designed to simplify the implementation of band-pass, high-pass, low-pass, notch, or all-pass filters using classical filter realizations (such as Butterworth, Cauer, Bessel, and Chebyshev).
-
product
NI-9253, 50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module
785989-01
50 kS/s/ch, ±20 mA, 24-Bit, 8-Channel C Series Current Input Module - The NI-9253 is an 8-channel analog input module for ComapctDAQ and CompactRIO systems. Each channel provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9253 has several diagnostic features to ensure your system is operating nominally at all times with open channel detection, power supply detection, and configurable thresholds. The NI-9253 has eight LEDs to indicate the status of each channel and the power supply so that a user in the field can easily validate that the system is operating normally. The NI-9253 also features a number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
product
6000 Series Analog I/O Modules
Series 6000 analog I/O modules condition, amplify, filter and digitize signals from virtually any transducer. All modules have conditioning & amplifier per channel and nearly all modules allow for setting bridge completion, shunt calibration, transducer power, gain, etc. individually per channel. Following the conditioning/amplifier stage, multi-pole Bessel or Butterworth analog filters are provided on each channel and can be set or bypassed individually by program control. A number of the modules include a high level analog output providing a conditioned/filtered output to a redundant, external A/D system. A 16-Bit Successive Approximation A/D follows the analog filter stage. Some modules use a single A/D with sample and hold while others have an A/D per channel. Sample rates are programmable per channel to easily accommodate mixing high and low speed measurements into a single data stream. Programmable hardware based warnings and alarms are included in the channel-by-channel architecture and are detected by digital output modules in the system, providing an ultra-low latency control capability directly from the data acquisition system.
-
product
sbRIO-9253, Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module
787433-01
Non-Enclosed, 50 kS/s/ch, 24-Bit, 8-Channel C Series Current Input Module - The sbRIO-9253 is an 8-channel analog input module for CompactRIO Single-Board Controller that provides a ±20 mA input range and 24 bits of resolution at a 50 kS/s sample rate. This module includes diagnostic functionalities to ensure nominal system operations with open-channel detection, power supply detection, and configurable thresholds. You can view the status of each channel and the power supply with eight LEDs. The sbRIO-9253 also features programmable hardware filters for your applications, such as specific Butterworth and comb filters that you can use to reduce the noise in your system.
-
product
NI-9252 , ±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module
786782-01
±10 V, 50 kS/s/ch, 24-Bit, 8-Channel C Series Voltage Input Module - The NI-9252 is an 8-channel analog input module for CompactDAQ and CompactRIO systems. Each channel provides a ±10 V measurement range and 24 bits of resolution at a 50 kS/s sample rate. The NI-9252 features a … number of programmable hardware filters. By choosing the specific Butterworth and comb filters for your application, you can significantly reduce the noise in your system.
-
product
Highpass Filters
Frequency range of this band pass filter is 1,000 MHz to 2.5 GHz and the passband is 1.5 GHz. PE8715 highpass filter is one of over 40,000 RF microwave and millimeter wave components supplied by Pasternack. Our 5 section highpass filter can be bought and shipped worldwide the same-day as with our other in-stock RF parts.
-
product
Notch Filters
Power-Pole Notch Series
POWER-POLE® Notch Filters offer improved performance and power handling over our MINI and MAXI Notch Filters.
-
product
Sine Filters
Sine Wave Output Filter Modules provide satisfactorily smoothed sinusoidal waveform with low residual ripple form square waveform with high voltage spikes, present at the output of motor drives.
-
-
product
Semrock Optical Filters
IDEX Health & Science offers a comprehensive line of Semrock optical filters. We set the standard in performance, quality, and reliability for the life science, point-of-care, clinical diagnostic, and analytical instrumentation industries. We have applied patented design techniques to create some of the most spectrally sophisticated optical filters on the market. Whether you select from our extensive catalog or we design a custom filter to your exact specifications, you can be confident of our uncompromising quality, reliability, and reproducible results.
-
product
Band Pass Filter
PA72BPF
The PA72BPF daughter board is an additional filter board. It typically contains two selectable differential 3rd order elliptic band pass filters. These filter modules are tailored by Applicos to the customers’ requirements. The filters can be used to filter the output signal of the generator daughter boards to achieve an even better distortion and noise suppression.
-
product
Bandpass Filters
These bandpass filters utilize a suspended stripline design to obtain a very compact configuration. Applications include wideband receiver input preselection and output filtering of frequency multiplied RF power sources.
-
product
RF Filters
Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.
-
product
LCL Filters
LCL Type Harmonic Filter Modules are used to filter out the input current harmonics of the Motor Drives having six-pulse diode/thyristor rectifiers, where harmonic current distortion exceeds the limits defined in standards.
-
product
High-Power Tunable Filter
CB503
The need for tunable filter technology originates from the fact that high power communication systems and IED Jammer transmitters severely limit the use of tactical radio communication systems on the battlefield.This clash within the radio’s spectrum during tactical missions is often de-conflicted using fixed high Q, high power RF bandpass and bandstop filters installed prior to mission. This can limit operational effectiveness due to the potentially large number of fixed filters required within the allocated radio communication channels, which need be transported, stored in the field, and fitted by trained personnel. Many of these fixed filters centred within the octave wide tuning range could be replaced by a single high-Q tunable filter.
-
product
Notch Filters
K&L Microwave provides notch filters, also called bandstop or bandreject filters, in multiple topologies built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications, as well as product families. Use the quote cart to request a quote on a specific design. When considering a particular family of parts, use Filter Wizard (a link button will be provided when appropriate) to determine a specific part number within the given family.
-
product
MEMS Tunable Filter
Optoplex’s MEMS Tunable Optical Filter is based on a patented micro-optic design with MEMS tuning technology. It is an integrated module consisting of a MEMS chip, micro-optics and control electronics and interface. When receiving a stream of optical signals of a plurality of wavelengths from the Input-Port (IN), the 2-port tunable optical filter directs a selected channel to the Output-Port (OUT). Wavelength (frequency) tuning is achieved by changing driving voltage applied to the MEMS chip, via the control electronics and the built-in firmware.
-
product
Tunable Filter Spectrometers
MKS Instruments' platform of innovative optical analyzers based on Tunable Filter Spectroscopy (TFS™) provides real-time gas analysis, while delivering customers a substantially lower total cost of ownership. TFS™ can be utilized from UV (Ultra-Violet) through IR (Infra-Red) spectral regions. MKS TFS™ sensor platforms have been on the market since 2008 with more than 2500 systems deployed.
-
product
Tunable Filters from Stock
K&L Microwave offers a variety of Tunable Filter Products to satisfy a broad range of filtering applications. Tunable Bandpass and Bandreject filters provide the best solution for pre-tuning desired signals while rejecting interfering signals. Mechanically-tuned, high Q cavity filters typically allow center frequency to be tuned over at least one octave.
-
product
Switched Filter Banks
Switched Filter Banks typically include multiple filter topologies, including PIN diode and MMIC switch sub-circuits to achieve operational bandwidths of greater than 3 octaves. Pin Diode Based Switched Filter Banks provide the highest level of signal isolation, higher operating power levels, and lower insertion loss and achieve switching speeds of < 40 nanoseconds. GaAs MMIC Based Switched Filter Banks provide switching times as low as 10 nanoseconds with very low power consumption and have the inherent advantage of supporting multi-octave frequency bands with extremely low power consumption.
-
product
SAW Filters & SAW Oscillators
Rich heritage in small form factor, high-rel SAW filters and oscillators for today's military and space markets.
