Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-FU-HV
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
32 Form C High Power Relay Module
DP-cPCI-4035
DP-cPCI-4035 is a cPCI-based 32-channel high power relay. It is designed as general-purpose module. Applications of this module include power routing, relay outputs for soft PLCs, automatic test equipment, hardware simulation and high current measurement routing.
-
product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
783864-02
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
product
PH Meter / Tester, 0pH to 14pH, 0.01, 0.2, 400 ms, 0 °C, 50 °C
72-6783
The 72-6783 is a 0 to 14pH Meter with 12.5mm LCD display. Any combination of pH electrode and male BNC connector can be used. pH meter included with battery.
-
product
Needle Microprobe
MT-29/1HT
Fast-response 29 gauge needle probe, (needle length is 1cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Dummy Load
Dummy load is capable of dissipating four times the legal limit 6 kW for 2 minutes and legal limit 1500 watts key down, forever. It covers the 160 meter to 6 meter bands (actually 1 Mhz-60 MHz continuously). It is a dry dummy load intended for testing amplifiers and station conditions. Two fans on the rear of the unit are automatically turned on when the internal temperature reaches 120°F/49°C . The unit runs off a universal AC supply. Simple to operate and use, the dummy load includes an RF sample output of -60 dBc.
-
product
300-Watt AC/DC Power Supply
56RS3
NAI’s 56RS3 is a 300 Watt AC/DC Power Supply that accepts a three-phase, AC input plus a +270 VDC input. This COTS unit provides a single full-power output (300 Watts) at a baseplate temperature of +85° C or a single 350 Watt output at a baseplate temperature of +70° C.
-
product
NI-9871, 4-Port, RS485/RS422 C Series Serial Interface Module
779892-02
The NI‑9871 adds RS485/RS422 serial ports to CompactRIO systems. The serial ports are accessed directly from the FPGA to offer you flexibility in communicating with serial devices. The module has individual buffers on every port that save FPGA space and simplify programming. The NI‑9871 supports standard start bit, stop bit, and handshaking settings. It uses an external power to provide maximum compatibility and reliability under all serial port conditions.
-
product
Portable Interface Unit
1553-USB-PIU
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
product
sbRIO-9211, Non-Enclosed, 4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module
780877-01
Non-Enclosed, 4-Channel, 14 S/s Aggregate, ±80 mV C Series Temperature Input Module - The sbRIO‑9211 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The sbRIO‑9211 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Non-enclosed modules are designed for OEM applications.
-
product
Portable Leeb Hardness Tester Probes
Beijing TIME High Technology Ltd.
There are 7 kinds of probes to work with Leeb hardness tester for different applications, which is D / DC / D+15 / C / G / E /DL.● Universal Impact Device D - For the majority of hardness testing requirements.● DC - Used in very confined spaces, e.g. in holes, cylinders or for internal measurements on assembled machines.● DL - For measurements in extremely confined spaces or at the base of grooves.● D+15 - For measurements in grooves or recessed surface.● C - Surface hardened components, coatings, thin walled or impact sensitive components (small measuring indentation).● G - Solid heavy or rough components. e.g. heavy castings and forgings.● E - For super hard materials.
-
product
XYZ Color Sensor
AS7261
Calibrated XYZ color sensor provides complete, integrated platform for handheld color analyzers, color calibration and mobile analysis devices. Tri-stimulus XYZ realized by silicon interference filters. UART or I²C slave digital Interface. 16-bit ADC with digital access. Programmable LED drivers. 20-pin LGA package 4.5mm x 4.7mm x 2.5mm, with built-in aperture. Compact true-color sensing. Applications; Color/CCT sensing, Fluid or reagent analysis, Color point comparison, Display calibration.
-
product
NI-9238, ±500 mV, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
783311-01
±500 mV, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9238 performs differential analog input. The measurement range is compatible with many low-voltage sensors such as current shunts and current transducers in high-current applications. When used with higher-voltage C Series Voltage Input Modules, the NI‑9238 can measure power and energy consumption for applications such as appliance test, industrial machine monitoring, power quality analysis, phasor measurements, and harmonic analysis.
-
product
NI-9220, ±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Modul
782615-01
±10 V, 100 kS/s/ch, 16-Bit, Simultaneous Input, 16-Channel C Series Voltage Input Module - The NI‑9220 performs simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. The module is capable of generating 3.2 MB/s of data at … the maximum sampling rate. There are two connector options for the NI‑9220: a 36-position spring-terminal connector and a 37‑position D‑SUB connector.
-
product
Extreme Temperature Active Probe, 1.5 GHz
N2797A
Testing devices over extreme temperature ranges is quite common these days. The N2797A single-ended active probe is the industry’s first low-cost high input impedance active probe with rugged probe tips for environmental chamber testing of ICs and devices. It gives the ability to probe signals at drastic temperature swings ranging from –40 °C to +85 °C. The probe provides 1.5 GHz of bandwidth and a 2 m long cable.
-
product
Modular Open Systems Approach (MOSA) Solutions
NAI’s Modular Open Systems Approach (MOSA) solutions provide customers with pre-configured, pre-validated, rugged military embedded solutions that save development time and cost while reducing program risk. These Flexible, Adaptable, Configurable, Modular and Expandable Systems Eliminate custom designs and redesigns by taking advantage of NAI’s Configurable Open Systems Architecture (COSA). NAI's full suite of MOSA Solutions are ARM® Cortex®-A53 processor-based and are ruggedized to withstand -40° C to +71° C and qualified to MIL-STD-1275D & MIL-STD-704A with 50 ms holdup (VITA 62 power supply); MIL-STD-461F and MIL-STD-810G.
-
product
Pico-ITX SBC With Intel® Atom® Processor E3845/E3827, LVDS/ VGA (HDMI), LAN And Audio
PICO840
The PICO840 ultra-small Pico-ITX embedded SBC supports the quad-core Intel® Atom® processor (code name: Bay Trail-I) and supporting DDR3L-1066/1333 MHz system memory up to 8 GB. Considering different environments, this industrial-grade Pico-ITX mainboard is built to withstand extreme temperature, ranging from -40°C to +70°C (-40°F to +158°F). Moreover, with superior integration and power efficiency, this compact size single board computer enables system developers and OEMs to create smaller, lighter, quieter devices than ever and embrace the new possibilities across POS systems, mobile medical monitor, compact panel PCs as well as multiple embedded computer, system and appliance segments.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, 2 COM, 2 LANs And DIO (2-in/1-out)
IFB122
The IFB122 is an extremely compact RISC-based DIN-rail industrial IoT gateway powered by the low-power Freescale i.MX 6UL-2 processor in the ARM® Cortex™-A7 micro architecture. Designed to meet the challenges in critical environments, it supports extended operating temperature ranging from -40°C to 70°C, flexible wide voltage range 9V - 48V DC power input, and can withstand vibration up to 5G. One PCI Express Mini Card slot, one SIM card slot, and two internal antennas are available for Wi-Fi and 3G/4G connections. With the abilities to transmit data and manage various devices, the IP40-rated ready-to-run IFB122 is definitely a cost-effective solution for remote control/monitoring management applications such as unmanned control room, industrial machine, automatic parking lot, traffic cabinet, etc.
-
product
Environmental Chamber/Stability Chamber - One Door Model
HC20
This is a Environmental test chamber/ Stability chamber/Laboratory incubator single door model capable of performing in wide temperature range(0°c to 70°c) with precise temperature control over the entire range.Humidity option is available , capable of maintaining 10% to 90%. Sensor Info–All units come with Rotronic hc2a-s model or equivalent
-
product
Gauge Type T Thermocouple Wire
W-TW-40P
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
product
MCB Thermal Trip Calibration Test Bench (IEC 60898 Cl 9.10.1.2, Annex I.1, IS)
The test system is designed and customized to carry out 2.55*Intest as per Table 7 (test c) of IEC 60898 (also mentioned for routine testing of MCBs. The test is done at dc current to exactly analyze and correct the bimetallic properties of the MCB as far as thermal tripping is concerned. The unit comes with a pneumatically operated test fixture with in-built dc stepper motor that is controlled by a micro controller / PC to calibrate the breaker into a narrow tripping band programmed by the user.
-
product
Current Transducer
IN 1000-S
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
product
Thermo-Hygrometer
*Display ambient temperature from -30°C to + 49.8°C*Key chain holder*Water resistant*Keychain (Optional)*Battery powered : 2 x 1.5V (L1154 / LR44 / AG13)
-
product
NI-9265, 4-Channel C Series Current Output Module
779334-01
4-Channel C Series Current Output Module - The NI‑9265 is ideal for interfacing and controlling industrial current-driven actuators at high rates. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing … outputs to ensure safety and avoid driving actuators at system power on. The NI‑9265 requires an external power supply and includes a channel‑to‑earth ground double isolation barrier for safety and noise immunity.
-
product
Handheld Water Quality Meters
LAQUA PH220
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers) - 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- °C & °F temperature readings- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrode and calibration solutions in carrying case- 3 years meter warranty
-
product
USB3 Vision Cameras
xiQ
*Ultra compact mini camera- Only 26.4 x 26.4 x 21.2 mm and mere 27grams (1)*Cool - Low power consumption with 1.0 to 1.8 W and minimal heat dissipation*Fastest - High speed, high frame rate: 500fps at VGA and 90fps at 4Mpix resolutions*AIA standard - USB3 Vision standard compliant*Supported - USB3 under Windows 7 and 10, macOS, Linux, ARM and various Machine Vision Libraries*Industry standard interface - Compatible with USB 3.1 Gen1 SuperSpeed specification*Powerful potential - 5 Gbit/s interface 400 MB/s data throughput*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Cost efficient - Excellent value for the price, low TCO and fast ROI*Software interfaces - GenICam / GenTL and highly optimized API / SDK for Image Processing*Easy deployment - Range of accessories and widest hardware and software interoperability*Time proven - In production since the end of 2011*User friendly - Intuitive and simple to use API, easy switch from C to CS mount and more*Highly Customizable - Available in Board level (single PCB) and with different connector types
-
product
C Series Voltage And Current Input Module
The C Series Voltage and Current Input Module features up to 16 input channels with built-in noise rejection. You can use this module to combine the two most common inputs to reduce the overall number of modules you need in your measurement system.The C Series Voltage and Current Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Fanless Embedded System With Intel® Core™ I5-6300U 2.4 GHz/i3-6100U 2.3 GHz/Celeron® 3955U 2.0 GHz, 2 HDMI, 2 GbE LANs, 4 USB 3.0, 2 COM And 9 - 36 VDC
eBOX565-500-FL
The eBOX565-500-FL is designed to support the 6th generation Intel® Core™ i5-6300U or Celeron® 3955U processor with one 260-pin DDR4-2133 SO-DIMM socket with up to 16GB system memory. The eBOX565-500-FL is designed for reliable use in industrial environments with an IP40-rated enclosure, a wide range 9 to 36 VDC power input, a wide temperature ranges from -10°C to 50°C (14°F to 122°F), as well as up to 3G vibration endurance. To fulfill various needs, the palm-sized industrial embedded computer, which measures 141.6 x 106 x 73 mm in size, provides rich I/O connectivity including two HDMI ports, one RS-232/422/485 port, one RS-232 port, four USB 3.0 ports, two Gigabit Ethernet ports, and two SMA type connector openings for antenna. One PCI Express Mini Card slot enables the addition of Wi-Fi, 3G, or LTE wireless cards.
-
product
85W to 120W - Single Output
HQA Series
*Standard Quarter Brick Footprint*9-40 Vdc, 18-40 Vdc Inputs*3.3, 5, 12, 15, 24, 28, 48 Vdc Outputs*2250 Vdc Isolation*-55 to 115°C Baseplate temperature*MIL-STD-461; 1275; 704; DO-160*No Optocouplers used
-
product
High-Performance Handheld Infrared Camera
FLIR T865
The FLIR T865 thermal imaging camera is a non-contact inspection tool with 180° rotating optical block that allows users to safely and comfortably assess the condition of critical electrical and mechanical equipment in utility and manufacturing applications. With advanced features including unmatched temperature measurements down to -40°C, accuracy as good as 1°C/1%, 1-Touch Level/Span contrast enhancement, and laser–assisted autofocus, you'll get highly accurate temperature measurements every time. Pair the T865 with a 6 FOV IR lens to perform inspections on small targets from long distances. The on-board Inspection Route system helps you record temperature data and imagery in a logical sequence for faster troubleshooting and repair. The T865 also features FLIR Ignite for automatic uploading of images directly from the camera to the cloud for easy, secure storage and sharing. Adding a FLIR T865 camera to a condition monitoring/predictive maintenance program can help reduce maintenance costs, improve system efficiency and reliability, and prevent downtime due to outages.
-
product
Coax, Contact, Receiver, 75 Ohm, RG179
610104157
Primary mating contact 610103169. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact - 5 mΩOuter Shield - 3 mΩCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
