Filter Results By:
Products
Applications
Manufacturers
-
product
Cable Identification System
After excavation, sometimes it is confusing to identify the right cable from a bunch of cables. Cable Identification is very important for the safety of field personnel – Cutting a wrong cable can be fatal. So, we require a Cable Identification System to identify the wanted cable.
-
product
Cable Identification & Phasing
VCi-3™
The VCi-3™ system is designed for cable and phase identification, mainly for installation or maintenance purposes on three-phase electrical networks during power shutdowns.The transmitter module injects a low current on the cable conductors by direct contact or magnetic clamps methods. A voice message is recorded by the user and will be transmitted along with digital signals. Groundings stay connected at both ends of the three-phase circuit during the test. The detector module is used at the other end of the cable system.
-
product
Cable Identification System & Cable Phasing System
Impulse Phaser
With the introduction of direct buried, solid dielectric primary voltage cables, the IMPULSE PHASER has come into greater prominence for safely and accurately identifying buried primary cables, including jacketed neutral designs. The IMPULSE PHASER has been accurately used on paper insulated, lead covered feeders in excess of 20 miles and even on submarine cable 300 feet underwater.
-
product
Cable Identification Instrument
HTDS-H / 410
Wuhan Huatian Electric Power Automation Co., Ltd.
It is mainly used to accurately identify one target cable from multiple cables.
-
product
Cable Identification System
KSG 200 / KSG 200 T
BAUR Prüf- und Messtechnik GmbH
Cable identification withBAUR KSG 200. The KSG 200 cable identification system is used to identify single- and multi-core cables in a cable bundle or cable loom. By using the KSG 200, the risk of accidentally cutting a live phase is significantly reduced.* Cable identification on all types of de-energised cables* Reliable verification of the cable identification by means of the highly precise three-factor-analysis ATP* Safe cable identification on live low-voltage cables* Connection technology according to CAT IV/600 V
-
product
Cable Identifier
K&S Engineering and Scientific Ltd
K&S Engineering and Scientific LTD's Cable Identifier Set offers the user a compact, portable solution for cable identification. Depending on the user preference, the Cable Function Generator and Cable Identifier Unit can be jointly housed in a rugged briefcase, or alternatively, for the user requiring a more rugged unit, can be delivered as two individual units each with their own carry-case. With the Cable Identifier Set, power optimum levels are selected by means of a rotary switch and the power levels are displayed on a meter located on the Cable Function Generator. As the Cable Identifier Unit is capable of detecting magnetic fields around mains cables it has the added advantage of the user being able to use this as a stand-alone unit to detect power cable configuration.
-
product
Cable Fault Locators
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
product
Cable and Pipe Locator
PT-14
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Network, Port ID And Cable Tester
One for All PH-400
The One For All is an all-in-one network tester, tone generator, cable tester, and port ID finder. It comes with a remote unit, allowing pin-by-pin tests of installed cables in addition to patch cables. The office ID feature allows the user to check the ID number of up to 100 networks or patch panel outlets without labeling the cables manually, and the tone generator traces cable using a tone detectable by any market tone probe. The network tester blinks the network hub or NIC port light for the cable being tested, allowing easy cable and outlet identification; and it identifies network speed (10 Mbps vs. 10/100 Mbps vs. 10/100/1000 Mbps) and activity. Line tester included for detect live circuits and preventing damage to the tester.
-
product
LAN Cable Multifunction Tester
TCT-2690PRO
LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.
-
product
Live Cable Identification Instrument
HTDS-V / 411
Wuhan Huatian Electric Power Automation Co., Ltd.
A special instrument used to identify a particular cable from a bundle of cables.
-
product
Energized Cable Identification System
LCI™
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
product
Low Frequency Generator
LFG-2500
• tracing – finding the route and burial depth of the underground utilities;• fault location – pinpointing phase-to-sheath and interphase short-circuit faults;• cable identification – identifying a correct cable in a bunch.
-
product
LAN Tester - RJ45, Coax, Tone
CZ20350
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Multi-function Cable Tester
NCT-100-S
*NCT-100-S Multi-Function Cable Tester Kit can help you quickly find network cables with OOK audio during network construction and maintenance. *Use TDR diagnostic technology to quickly and accurately locate fault points and accurately measure wiring diagrams and lines. Cable identification, etc.
-
product
Low Frequency Generator
LFG-50
• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
Coaxial Cable Tester
6106
Peaceful Thriving Enterprise Co Ltd
This device is designed to test the connection of F type coaxial cable. The testing includes continuity and cable mapping. The tester includes 4 mapping terminals with different color and a F type adapter, which are very helpful for cable identification.
-
product
LAN Tester
RJ45
This easy to operate LAN tester enables you to test your wiring and connections at installation or after maintenance, making it one of the most convenient tools on the market. With the press of a single button you can automatically run a barrage of tests, including tests for Continuity, Opens, Shorts, Crosses and Splits. You can also identify which pairs require correction; The unit will scan all combinations without you having to do anything other than initiate the test. Even cable shield is tested for continuity! Building on the features provided by other testers such as the CZ20250, this LAN tester will also test coax networks and provide a tracing tone for cable identification. And it tests for all these at lightning speed, saving you as much time as possible.
-
product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Ferrules, 0.5m
40-972-037-0.5m-FU
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
Cable Assembly, Receiver, QuadraPaddle, 72", 100-Pin Male SCSI
540009040540
Cable Assembly, Receiver, QuadraPaddle, 72", 100-Pin Male SCSI
-
product
68-Pin VHDCI Cable Assembly, Male to Male, 2m
A068VMR-068VMR-6C200
This 2m long male to male cable assembly is suited for direct connection to various products using the 68 Way VHDCI connector.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Male (Male Screwlocks), 0.5m
40-970B-200-0.5m-MM
This male to male 0.5m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by male screwlocks.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Cut Ends, 2m, HV
A009DF4-C-HA200
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
product
Cable Assembly, Receiver, Mini Power/TriPaddle, 48", 9-Pin DIN and 4 Banana Plugs
540039010611
Cable Assembly, Receiver, Mini Power/TriPaddle, 48", 9-Pin DIN and 4 Banana Plugs
-
product
Cable Assembly, Receiver, 36", TriPaddle, to 37 Pin Female D-Sub
540016020203
Cable Assembly, Receiver, 36", TriPaddle, to 37 Pin Female D-Sub
-
product
50 Ohm SMA to SMA Cable Assembly
40-977-521-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Cut Ends, 2 Amp, 2m, 250 Port
A500RMR-C-5C200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products. Unterminated connections are provided at the other end of the cable for a variety of applications. Screwlocks enable the SEARAY connector to be secured to its mating product.
-
product
Cable Assembly, 50-Pin D-Type, Female to Female, 0.5m HV, Exit Away From Pin 1
40-970-050-0.5m-FF-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Cut Ends, 0.5m
A026HM5-C-0A050
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. Please ensure appropriate electrical safety precautions are observed when using this product.
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 0.5m, 500 Port
A500RMR-500RMR-0A050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
