Filter Results By:
Products
Applications
Manufacturers
- TEAM SOLUTIONS, INC.
product
HandyScope HS5: 200 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-220XM-W5
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 200 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
product
Vector Network Analyzer
Bode 100
With the multifunctional Bode 100 you get an exact picture of your electronic circuits and components in a frequency range from 1 Hz to 40 MHz. The Bode 100 is not only a state of the art Vector Network Analyzer, it also works as: Frequency Response Analyzer, Impedance Meter, Gain Phase Meter, Sine Wave Generator.
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (m) 50 Ohm
CK520A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Vector Network Analyzers
One of the most important measurement tasks in radio engineering is the analysis of electrical circuits. A network analyzer is an instrument that is designed to solve this problem with high accuracy and efficiency. The circuits that can be analyzed with network analyzers have a wide range of applications ranging from simple devices such as filters and amplifiers to complex modules used in communications satellites. PLANAR specializes in the development and production of vector network analyzers that combine the capabilities of scalar network analyzers that measure not only the amplitude components of the main characteristics of the system (gain, loss, standing wave ratio, etc.), but also allow measurements of the amplitude and phase characteristics of the system .
-
product
Frequency Expansion Modules
bsw TestSystems & Consulting AG
Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.
-
product
Launch Analyzer
2440
The 2440 Launch Analyzer is the first fully automated test system for characterizing the optical power distribution of the light produced by VCSEL laser sources, multimode fiber test equipment and launch cords utilized in multimode fiber links. Built on over 20 years of experience testing the transmission and geometric properties of muitimode fibers, the 2440 is the ideal solution for ensuring that source launches comply with applicable international component specifications and measurement standards. The 2440 can be configured for measurements in either or both the 850 and 1300 nm windows.
-
product
Radio Vector Tester
Wuhan Sunma Technology Co., Ltd.
Radio & Vector Network Analyzer adopts the advanced digital and RF combination design technology, fundamental wave frequency mixing technology, digital IF processing technology, intelligent power management technology, etc. It comes with features of high precision, small size, light weight, battery power, can measure SWR, Return Loss, Cable Loss, Impedance, DTF, etc, is used to the field test of cable, feeder, and the reflection parameters test of RF components in science and teaching. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
product
Near Field Probes 30 MHz up to 3 GHz
RF1 set
The RF1 near field probe set consists of 4 passive near field probes for making measurements in the development phase of E-field and magnetic field in the ranges of 30 MHz to 3 GHz on electronic assemblies. The probe heads of the RF1 set allow for measurements close to the electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors in order to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through a trained special use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They do not have an internal terminating resistance.
-
product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
product
Mixed Signal Oscilloscopes
A Mixed Signal Oscilloscope (MSO) is a combination Logic Analyzer and Oscilloscope. Since all inputs sample simultaneously, it is easy to see the timing relationships of the digital and analog components of your circuit. The extra channels also allow for more complex triggering. All of our MSOs have Oscilloscope triggering, Logic Analyzer triggering, SPI triggering and I2C triggering.
-
product
PNA Microwave Network Analyzer
N5227B
Meet your toughest measurement challenges with the highest performing microwave network analyzer in the industry Measure S-parameters with the smallest uncertainty and highest stability Efficiently characterize active components with applications that simplify setups Meet your specific budget and measurement needs by customizing to just the right level of performance Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
Continuous Gas Analyzer
CT5100
Emerson CT5000 series, providing the most comprehensive analysis available as it can detect down to sub ppm level for a range of components, while simplifying operation and significantly reducing costs. Unlike traditional continuous gas analyzers, the CT5100 can measure up to 12 critical component gases and potential pollutants simultaneously within a single system – meeting local, state, national, and international regulatory requirements.
-
product
RF Components
Using a Vector Network Analyzer (VNA) for RF component testing for design and manufacturing is based on how the component performs. The analyzer is used in multiple ways from design to manufacturing to tuning, field monitoring and maintenance of antennas, filters, mixers, amplifiers, circulators, isolators, and other RF components. Key considerations component designers should pay attention to when finding an analyzer that fits their needs is a great dynamic range, low trace noise, and fast measurement speed.
-
product
Medical Devices
As more medical devices become wireless, manufacturers will be looking for compact and affordable testing solutions for wireless components. Copper Mountain Technologies’ USB vector network analyzers provide portable, cost-effective network analysis solutions for medical wireless device applications.
-
product
Gas Analysis
Accurate measurement of gases and their concentrations is critical in many applications, and often poses a major challenge. Sensors' experience with different measurement principles, including NDIR, NDUV, and thermal conductivity, along with the ability to provide special combinations of these techniques within our products, enables us to tackle these challenges. In addition, our experience goes into every detail of our gas analyzers, ensuring reliable results, even under harsh conditions. Our skilled team of experts is happy to assist you in finding the optimized solution for your measurement requirements, with either off-the-shelf components or a customized solution.
-
product
Flue Gas Multi-Component Gas Concentration Analyzer
NSA-3080
The NSA-3080 is infrared gas analyzer for monitoring stationary sources The NSA-3080 can measure up to five components NOx, SO2, CO, CO2, and O2 with a high degree of accuracy. NSA-3080 uses the ratio infrared absorption method, and it ensures highly stable measurements. The slim cubicle structure used makes maintenance and daily inspections extremely easy to perform. Highly reliable sampling can also be performed with ease.
-
product
4-in-1 OSLT Calibration Kit, DC to 26.5 GHz, Type-3.5 mm (f) 50 Ohm
CK521A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
PXIe Vector Network Analyzer Source, 1 MHz To 6 GHz
M9389A
The M9389A PXIe vector network analyzer source is a component for the M9485A PXIe multiport vector network analyzer. The M9389A configuration includes two PXIe modules (M9310A source output, M9309A synthesizer) and its control is provided through the M9385A software front panel (SFP). The M9485A provides a true multiport VNA with up to 12-ports in one chassis and up to 24 ports in two chassis.
-
product
PNA-L Network Analyzers
The Keysight PNA-L network analyzers help you with your general-purpose network analysis needs. The PNA-L network analyzers give you efficiency and flexibility in both manufacturing and R&D applications. The PNA-L VNA covers various industries ranging from mobile telecommunications, wireless LAN component production, and aerospace and defense. The PNA-L network analyzers balance value and performance using the Keysight PNA network analyzer's core firmware.
-
product
On-Board Systems
OBS-ONE series
HORIBA developed the OBS-ONE series on-board emission measurement system in response to new requirements for exhaust emissions measurement from vehicles being driven on public roads (Portable Emissions Measurement Systems - PEMS). This development has been made possible by reducing the dimensions and power consumption of laboratory grade analyzers and ensuring that the system components have excellent vibration resistance. The OBS-ONE series continuously measures not only the concentration of CO, CO2, THC and NOx, but also measures exhaust fl ow rate and A/F ratio to calculate mass emission and fuel economy.
-
product
CX4000 – FTIR Gas Analyzer
Gasmet CX4000 is an industrial multi-component FTIR gas analyzer for continuous emission monitoring applications, integrated into a Continuous Emissions Monitoring system (CEMS II e). It can be used to measure up to 50 components simultaneously, and additional gases can be easily added without any hardware changes. The corrosion-resistant sample cell is heated up to 180 °C, which makes CX4000 an ideal tool for analyzing trace concentrations of pollutants in wet, corrosive gas mixtures.
-
product
110 GHz Lightwave Component Analyzer
N4372E
The N4372E lightwave component analyzer helps you with optoelectronic tests with its measurement capability of 110 GHz in an extended wavelength range. It also offers RX testing up to 110 GHz in the full 1260 nm to 1620 nm range. It has a built-in optical power meter that enables you to check and control the operating power. The N4372E lightwave component analyzer's optical transmitter input port connects to an auxiliary tunable laser to verify S-parameters over wavelength.
-
product
Portable Fuel Analysis
MINISCAN IR Vision
The MINISCAN IR VISION is a high speed, compact and robust FTIR fuel analyzer for the comprehensive and automatic measurement of gasoline, jet and diesel fuels. The analyzer is configured to measure more than 100 fuel parameters and components for fuel blending, for quality inspection and to check compliance with fuel specifications directly at the point of sale.
-
product
Portable Gas Analyzer
PG-300 Series
The PG-300 is a compact and lightweight stack gas analyzer that can simultaneously measure up to five separate gas components. Its capability of providing precise measurement has been proven for field measurements and also for laboratory applications. The PG-300 series also offers the capability to measure methane (CH4). A 20% weight reduction over previous PG models and integration of shock-resistant side guards make the PG-300 a robust analyzer for use in the field. An optional electronic cooler unit is available for long-term measurements for severe monitoring applications as gas turbines, boilers, and incinerators PG-300 series versatility makes the analyzers suitable for investigating environmental problems, evaluating catalyst performance, and for controlling process gas streams.
-
product
ChemWiz Analyzer Development Kit
Full spectrum chemometric analysis for multiple components can now be performed using the ChemWiz® Analyzer Development Kit (ADK). This software toolkit, when combined with StellarNet spectrometer instrumentation and SpectraWiz operating software, enables rapid development of complex analyzers needed to provide custom measurement solutions for many applications.
-
product
Wound Component EST Analyzer
19036
Chroma Systems Solutions, Inc.
The industry’s first Wound Component Electrical Safety Test (EST) Analyzer that combines impulse winding, AC/DC hipot, insulation resistance and DC resistance test measurement functions. Chroma’s 19036 Wound Component EST Analyzer has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement with a maximum output of up to 40 channels. Capable of outputting and measuring AC100mA/DC 20mA, Chroma’s 19036 is suitable for testing to high power motor standards such as UL 1004-1.
-
product
Impedance Analysis For E5061B-3L5 LF-RF Network Analyzer
E5007A
The E5007A provides the impedance analysis (ZA) firmware for the E5061B LF-RF network analyzer. This option enables the analyzer to measure impedance parameters of electronic components such as capacitors, inductors, and resonators. The combination of NA and ZA capabilities further enhances the analyzer’s versatility as a general R&D tool. Basic ZA functionalities including fixture compensation and equivalent circuit analysis are supported by the firmware. The DC biased impedance measurement is possible with the built-in DC bias source provided by the E5061B-3L3/3L4/3L51.
-
product
4-in-1 OSLT Calibration Kit, DC to 40 GHz, 2.92 mm (m)
CK562A
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
product
Optical Modulation Analyzer and High-speed Digitizer Test Solution
M8290A
The M8290A is a flexible solution platform for 400G coherent component and transmitter test. It incorporates a 92 GSa/s modular optical modulation analyzer and a 92 GSa/s 4-channel electrical digitizer. Besides these modules an additional arbitrary waveform generator module up to 92 GSa/s, such as the M8196A, can be added to the same AXIe chassis. This setup results in a compact and flexible coherent test solution that can be used together with additional specialized solution software for Integrated Coherent Receiver (ICR) and Analog Coherent Optical (ACO) module characterization.
-
product
GSX Monitor And Analyzer For Skype And Business
Monitor, Report and Alert on the Components and Services that Really Matter when Using Microsoft Skype for Business services. Keep your Skype for Business under control with GSX Solutions by monitoring server status as well as the services delivered to business lines. GSX Monitor & Analyzer streamlines communication by delivering the critical information you need to proactively manage Skype for Business and avoid any system outages.
-
product
Real Time Spectrum Analyzers
RSA600 Series
Visualize and characterize your device or component with the precise and accurate RSA603A and RSA607A USB Spectrum Analyzers, packed with features to aid in wireless integration, EMI, and IoT projects.
