Filter Results By:
Products
Applications
Manufacturers
Similar Topics: DoS
DOS
-
product
Microprocessor Development System
DS-48
# Real-Time and Transparent In-Circuit Emulator# Supports Philips Telecom Derivatives# Adaptable to 8051 Derivatives# Emulates 1.5V to 6V Microcontrollers# Maximum Frequency of 40MHz# 8K of Internal Memory# DOS and MS-Windows Debuggers# 32K Trace Memory and Logic Analyzer "on the Fly"# 8K Hardware and Conditional Breakpoints
-
product
Low Cost Emulator
EB-51
# Emulates 80C51 Microcontrollers and Derivatives# Real-Time Operation up to 40 MHz# 3.3V or 5V Voltage Operation# Source-Level Debugger for C, PLM and Assembler# DOS and MS-Windows Software# Support for ROMless and ROMed Microcontrollers# 64K of Code and 64K of Data Memory# Data Memory with Mapping Capabilities# Performance Analyzer# Real-Time and Conditional Breakpoints
-
product
1U Quad Bit Sync for Data Rates up to 40 Mbps
LS-44-QBS
The LS-44-QBS contains up to 4 Lumistar LS-40-DB25 Bit Synchronizer Daughterboards in a 1U RackMount chassis with status lights on the front panel and all interconnections through the rear. The design contains an internal computer which runsoff DOS or Windows depending on the version selected. The DOS version boots quickly without the delays required for Windows startup. The Windows version offers networking. The unit can be connected directly to the optional 1U slideout keyboard/display, for setup resulting in only 2U of total rack height. For applications that require many bit synchronizers, a 1U keyboard/Display with KVM switch allows 32 bit synchronizers in 9U of rack height. When power is applied, the computer will operate with the last configuration unless the operator wishes to change the setup. For setup, the keyboard/display is pulled out and the display is flipped up to monitor the process. When the bit synchronizer setup is completed, the keyboard/display canbe closed up since the status can be monitored on the front panel without an external display.
-
product
DOS Decoder
CODE300-32
Is a software based demodulator, decoder, an analyzer which runs under all actual Microsoft Windows operating systems. CODE300-32 continues our long experience with data decoders and anlyzer,
-
product
ISA bus GPIB Controller Card
Model 488-PC2
* Adds GPIB Controller capability to any PC with an ISA bus.* Fast data transfer rate, > 300kbytes per second.* Drivers for MS DOS, Windows 3.1, Windows 95 and Windows 98. * IEEE-488.2 linkable libraries for Quick Basic, MS Visual Basic, Borkand C/C++ andMicrosoft C/C++.* Functions as System Controller, Controller-in-charge or a GPIB Device.* Replaces most generic ISA 7210 Cards and NI PC2a cards.* Includes interactive keyboard Control Utility for controlling instruments from the computer keyboard without writing a program.
-
product
Software
Spectrum Lab
Spectrum Analyzer with Waterfall Display and real-time audio processing.This program started as a simple FFT program running under DOS a long time ago, but it is now a specialized audio analyzer, filter, frequency converter, hum filter, data logger etc.
-
product
UDP Test Tool, Flood Generator, VoIP Readiness Test Tool
The Multiprotocol Network Tester is a freeware, open source tool which enables you to measure quality of your IP network. It can also be used to generate UDP flood or to simulate UDP DoS attack. SIP call is usually established using a SIP session with a bidirectional RTP stream. SIP and RTP protocols are based on UDP transport protocol. UDP uses a simple transmission model without implicit reliability, ordering and data integrity. Each single UDP packet is transferred independently. The quality of a SIP call depends on delays and loss of IP packets in a network. Long delays lead to large RTP jitter and bad sound quality of a SIP call.
-
product
Smart Polyglot - Wireless Probe
Signals & Systems India Private Limited
Smart Polyglot is designed to talk to meters of all protocols – PACT, ANSI, IEC. Not only does it talk over optical media, it interfaces with IR, IrDA meters as well, making it the only device that talks to any type of meter in any language.The Smart Polyglot has a wireless Bluetooth interface and enables seamless use with any DOS, Android, or Windows based devices with Bluetooth support. This Smart Polyglot Bluetooth probe can detect the commands from Bluetooth connected devices and establish a connection automatically for meter reading applications.
-
product
Interface Adapter
DMX-10
DMX-10 is, all-in-one ready to use PCIEx to I2C/SPI/GPIO Interface adapter based on system with FPGA and 1x PCIEx PHY. DMX-10 converts PCIEx transactions into the I2C, SPI master or slave transactions and GPIO control functions. DMX-10 turns your PC running Windows, DOS, Linux, MacOS or any embedded OS with PCI support into comprehensive general purpose bus master or slave adapter.
-
product
Security Testing
We protect your business from cyber attacksSecure online transactionsPrevent unauthorized accessMinimize the risk of data lossEnhance resistance to DoS attacks
-
product
Fifo Serial Analyzer for DOS
FLL
FLL is a DOS based protocol analyzer for debugging serial asynchronous communication. FLL uses the standard COM1 and COM2 ports of a PC and does not require any other hardware except for the physical connection to the line.
-
product
Noise Dosimeter
doseBadge5
The doseBadge5 is the next generation doseBadge noise dosimeter from Cirrus. It provides all of the unique features of the original doseBadge such as no controls, cables or displays with a range of new functions and features allowing it to be used for compliance with any occupational noise standard. Wireless communication to the dBLink App (for Android and iOS) or the doseBadge5 Wand allows the instrument to be configured and controlled without user intervention. Measurements can be scheduled to start, pause and stop automatically with the timer functions allowing the doseBadge5 to be deployed quickly and easily.
-
product
Liquid Handling
Dosimat plus
Taking care of all kinds of dosing and liquid handling tasks, Dosimat plus instruments are indispensable in many modern laboratories. Used as an independent system, the Dosimat plus is a manually controlled dosing instrument. If you are already using a Titrino or Titrino plus titrator in your lab, you can use the Dosimat plus as an automated dosing device for your titrator.
-
product
Occupational Noise Measurements
doseBadge
The doseBadge is the original wireless personal noise dosimeter. It is the ideal tool to carry out occupational and industrial hygiene noise measurements and provides a unique solution for these applications.
