Filter Results By:
Products
Applications
Manufacturers
DWDM
Dense Wavelength Division Multiplexing
-
product
DWDM Channel Analyzer
AE700
AE700 is a DWDM Channel Analyzer for the installation and maintenance of DWDM systems. The handheld unit is able to measure wavelengths in the c-band, which is from 1530 to 1565 nm. The AE700 also supports optical signal to ratio (OSNR) which is essential for verifying signal quality. The measurements can be displayed in both graphical or list formats.
-
product
Optical Performance Monitor
Optoplex Optical performance monitor (OPM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical performance monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controlling network elements so as to optimize operational performance. In particular, Optoplex Optical performance monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength and power. See the following schematic diagram for OPM working principle.
-
product
(100×130×19mm) C-Band DWDM Pre-Amplifier EDFA Module
WPA4300-FM04
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai WPA4300-FM04 series with 100 × 130 × 19mm Compact package, is a digital control circuit with DWDM full function preamplifier module. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, low noise, excellent gain flatness characteristics and transient characteristics. Suitable for C-Band 44 or 88 wave wave DWDM system applications.
-
product
100GHz DWDM Module(4,8,16 Channel)
Flyin Optronics’ 100GHz dense wavelength division multiplexer (DWDM) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add and drop at the ITU wavelengths. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
VOA MUX/DEMUX (DWDM) With VOA Dense Wavelength Division Multiplexer
DWDV-1000 (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDV-1000 series, integrate of DWDM and Electronically controlled variable optical attenuator (VOA) in 1RU or 3U chassis, each channel of DWDM has one high-resolution electronically controlled variable optical attenuator, adjust the optical power. Compact and simple device structure reducing the number of connections between devices, improve the system parameters and device reliability. It can be easily and flexibly used in DWDM system inter-channel power adjustment and automatic balance, optical add-drop multiplexing (OADM).
-
product
Fixed Laser Source Module
Keysight offers a broad choice of fixed laser sources, which are available as single-wavelength and dual-wavelength modules as part of the Keysight Lightwave Solution Platform. The Keysight 8165xA Fabry-Perot laser sources can be used in conjunction with optical power meter modules for insertion loss, optical return loss and PDL measurement of broadband components and fiber. The Keysight 81663A Distributed Feedback Laser Sources are best suited for amplifier test and WDM system test applications. Keysight covers PON and common WDM wavelengths with its 81663A Distributed Feedback (DFB) laser source modules. The precise tunability around ITU-grid center wavelength gives you the flexibility to match test setups to the latest requirements of the DWDM-system. The fine-tuning allows to shift the center wavelength from one DWDM transmission channel to the adjacent channel in dense WDM systems. The built-in isolator ensures highest laser stability, even when reflections are present in the optical path.
-
product
Pluggable Optical Line System
POLS
Use our compact pluggable modules to provide up to 8 DWDM channels to enable high-capacity optical inter-datacenter links for internet service and cloud hosting providers.
-
product
100G,200G 1X2 DWDM Device (3Ports)
Flyin optronics’ 100GHz/200GHz 1x2 wavelength multiplexer utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging to achieve optical add or drop at a ITU wavelength. It provides ITU channel center wavelength, low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path . It can be used for wavelength add/drop in telecommunication network system.
-
product
(125×150×20mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM05 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
EDFA Optic Amplifiers
Wuhan Sunma Technology Co., Ltd.
With the feature of high input power, high output power, and medium optical gain, the booster amplifier operates at the transmission side of the link to amplify aggregated optical input power for reach extension.SunmaFiber booster amplifier is a low-noise, gain-flattened C-band optical erbium doped fiber amplifier (EDFA) designed to cost-effectively extend the optical link power budget for building long distance DWDM solutions.SunmaFiber also offers switches, routers and fiber converters including 10/100M, 10/100/1000M and 10G fiber converters, SFP fiber converters, manageable/unmanageable fiber converters, OEO fiber converters, POE fiber converters, fiber converter cards, and fiber converter chassis; transmitting distance from 2km(MM) to 150km(SM) with SC or LC or FC connectors.
-
product
Splitters, WDM, CWDM, DWDM
OPTOKON manufactures an extensive range of reliable and field-proven fiber optic components designed to increase system capacity. To be cost-effective, these compact solutions assist service providers, dark fiber developers, and enterprises to increase fiber capacity while keeping growth flexibility and high ROI. By providing the necessary platforms for a smooth and effective transition into optical networks they fulfill high bandwidth needs while cutting implementation, upkeep, and growth costs.
-
product
Compact & Robust Tunable Laser
WSL-110
Designed for use in fiber optic transmission testing, our WSL-110 can also be used for DWDM component evaluation and coherent communications testing. The WSL-110 features grid tuning and gridless tuning options, allowing any wavelength to be accessed.
-
product
Optical Channel Monitor
Optoplex Optical channel monitor (OCM) uses proprietary thin-film interference filter technology combined with a micro-actuator and high-speed electronics. Optical channel monitor is used to measure critical information data on optical transmission signals in DWDM networks for monitoring signal dynamics, determining system functionality, identifying performance change, and providing feedback for controling network elements so as to optimize operational performance. In particular, Optoplex Optical channel monitor can automatically scan the C-, L- or C+L-band wavelength range and precisely measure channel wavelength, power, and optical signal-to-noise ratio (OSNR). See the following schematic diagram for OCM working principle.
-
product
100GHz DWDM Optical Add/Drop Multiplexer (CATV Overlay Multiplexer)
OADM-1001-VOA (100GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai OADM-1001-VOA is an optical Add-Drop multiplexer with 100GHz channel interval. It is based on mature thin film filter technology, sealed with metal shell, and featured with low insertion loss, high isolation, wide channel and flexible configuration. It is the ideal device to Add(insertion Add)/Drop(Tape-out Drop) a specific wavelength(OADM) in optical fiber DWDM system. OADM-1001-VOA configures a manual-adjust optical attenuation, for adjust the equilibrium the optical power between insert channel and main signal channel, which is conveniently used for VOD overlay in CATV system.
-
product
Clock and Data Recovery/Retiming
Analog Devices provides single rate, multiple rate, and continuous tuning clock and data recovery (CDR) ICs for metro, long haul, DWDM, FSO, instrumentation, and other applications. Our any rate CDR ICs allow easy integration into protocol agnostic applications, automatically locking onto incoming data streams at any rate, from 10 Mbps to 2.7 Gbps or from 6.5 Mbps to 11.3 Gbps, without the aid of a reference clock while reporting the acquired data rate over the I2C interface. With a proprietary dual loop design, our any rate CDR ICs feature fast locking with superior jitter performance.
-
product
Dense Wavelength-Division Multiplexing
DWDM
Dense Wavelength-Division Multiplexing (DWDM) entails transmitting signals at multiple closely spaced wavelengths through the same fiber. ACP offers DWDMs with channel spacing of 200, 100, or 50GHz; corresponding to about 1.6nm, 0.8nm, or 0.4nm respectively.
-
product
C & L-Band Separate Raman Fiber Amplifier
RFA7000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
100GHz Dense Wavelength Division Multiplexer
DWDM-1000
Hangzhou Huatai Optic Tech. Co., Ltd.
DWDM series is based on mature thin film filtering technology and adopt metal sealing technology to encapsulate. It has the feature of flat channel bandwidth, flexible channel configuration, low insert loss and high isolation. The flexibility of channel configuration and modularized design make it convenient for system upgrading and expanding. All the Huatai products have no epoxy glue in optical line and can be used in high power optical communication system.
-
product
Optical Power Meter with Optical Head
GM8012 + 2 X GM8300X
The UC8820 + 2 X UC8820X optical power meter with optical head offer superior performance for the test of DWDM components, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications. It is special design for volume production line application.
-
product
Tunable Laser Source Module
Keysight's has a wide range of tunable laser sources to fit your needs for various applications. In addition to the proven 81600B tunable laser source family, Keysight recently introduced a new family of tunable laser sources - the 8160xx family. The 8160xx tunable laser sources offer the full wavelength range from 1260 nm to 1650 nm with no wavelength gaps. All 8160xx tunable laser sources are modules for the Keysight 8164B lightwave measurement system mainframe. This provides test instrumentation with maximum flexibility. Investing in the Keysight 8160xx family of tunable laser sources can realize the cost efficiency and performance required to test components for coarse and dense wavelength division multiplexing (CWDM, DWDM) and passive optical networks (PON).
-
product
Optical Spectrum Analyzer
S6362D
Saluki S6362D is a high-resolution, large-dynamic, high-speed, high-performance optical spectrum analyzer. It is perfect for testing 600 nm to 1700 nm optical systems, such as DWDM and optical amplifiers. It can also be used for optical active and passive device testing, such as LED, FP-LD, DFB-LD, optical transceivers and optical fibers and fiber gratings and other optical devices.
-
product
Multi-Wavelength Meter
86122C
With an absolute wavelength accuracy of 0.2 ppm and 0.15 ppm differential accuracy, the new Keysight 86122C Multi-Wavelength Meter belongs in the top class of wavelength meters available for optical communication testing. Its wavelength range of 1270 to 1650 nm covers all fiber-to-the-home, metro and long-haul transmission systems. The instrument can measure the spectra of up to 1,000 laser lines at once, which is more than sufficient for fully populated dense-wavelength-division multiplexed systems (DWDM).
-
product
L-Band Separate Raman Fiber Amplifier
RFA6000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
100GHz Single Fiber Bi-Direction Dense WDM
DWDM-1200
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai DWDM-1204, DWDM-1208 dense DWDM DWDM, which is based on mature thin film filtering technology, It has the feature of low insertion loss, high isolation and flexible channel configuration. It can bi-direction transmit 4 channel(1204) or 8 channel(1208) on one fiber up stream/down stream.
-
product
C-Band DWDM Line Amplifier EDFA (WLA-C)
HWA4200 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HWA4200 series, is designed for C-Band 44 waves or 88 waves DWDM system design Line Amplifier gain flatness. Products using the most excellent optical performance, the most advanced electronic control technology and comprehensive software features, has a wide operating wavelength range, Low noise, excellent gain flatness characteristics and transient characteristics.
-
product
1310nm/1550nm Fused Biconical Taper WDM
SWD1315
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai SWD1315 single mode DWDM adopt fused bi-conical taper technical with low insertion loss, channel flatness features. Mainly used in optical network 1310nm and 1550nm combination and halve.
-
product
Multiplexers (MUX)
WDM
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
-
product
Hybrid Raman/Er-doped Fiber Amplifier
HFA5000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600nm.
-
product
80-CH 50G Athermal AWG
Athermal AWG(AAWG) have equivalent performance to standard Thermal AWG(TAWG) but require no electrical power for stabilization. They can be used as direct replacements for Thin Film Filters(Filter type DWDM module) for cases where no power is available, also suitable for outdoor applications over -30 to +70 degree in access networks. Flyin’s Athermal AWG(AAWG) provide excellent optical performance, high reliability, ease of fiber handling and power saving solution in a compact package. Different input and output fibers, such as SM fibers, MM fibers and PM fiber can be selected to meet different applications. We can just offer 19” 1U rackmount package for 50G AWG products.
-
product
Band DWDM EDFA
MSA Module C
Amonics now packages one of its most popular product lines, C-band DWDM Erbium-doped Fiber Amplifiers (EDFAs), into standard MSA size. The same reliable, stable and durable EDFAs are thus readily available for system integration of a wider range of applications. The devices provides the usual alarms and status indicators, with an integrated RS232 computer interface for easy control, diagnostic functions and data acquisition. This MSA series will be expanded to cover EDFAs of different specifications in our product range in order to meet the growing demands.
