Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
LXI WTB Adaptor, Thru line
60-982-001
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
product
Microwave Wideband APD-TIA Receivers
MR12 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR12 series microwave wideband optical receiver, adopts high Sensitivity APD diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
product
3 GHz Programmable Delay Line
PADL3
The PADL3 is a single channel programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 3 GHz
-
product
Microwave Delay Line
E501
The Eastern OptX Series E501 / Microwave Delay Line is a high performance turnkey solution for radar and communications market. The E501 allows for ultra wide bandwidth, low loss, high isolation and immunity from EMI and EMP with timedelays up to 250 usec at frequencies up to 18 GHz.
-
product
5 Gb/s Programmable Digital Delay Line
QPDDL5
The QPDDL5 series delay lines are four channel precision time delay generators for digital signals. Delays are controlled precisely in 5 or 10 ps increments at data rates up to 5 billion bits per second or clock rates exceeding 2.5 GHz. Each of the four channels is independently programmable.
-
product
ARM LPC2364 Board
MS 1541
- 128KB On chip Flash- 16*2 line LCD Module interface- Two CAN channel at 1MPBS- Ethernet interface which supports 10/100 MBPS- Full Modem RS232 interface- RS485 interface- RTC (Real Time Clock)- 2048 bits serial EEPROM with data protect and sequential read.- 24 ULN outputs of 12V level.- Eight 110V DC inputs interface.- Six digital inputs interface- Four on board keys interface- Power delay circuit for external use- ON board inspection circuit
-
product
10 Gb/s Programmable Digital Delay Line
QPDDL10
The QPDDL10 series delay lines are four channel precision time delay generators for digital signals. Delays are controlled precisely in 5 ps increments at data rates up to 10 billion bits per second or clock rates exceeding 5 GHz. Each of the four channels is independently programmable.
-
product
Synchronization And ASOPS Systems
The asynchronous optical sampling (ASOPS) technique allows high-speed scanning over some nanoseconds of time delay without a mechanical delay line. The SYNCRO-RRE, also available as stand-alone unit, provides state-of-the art phase lock electronics.
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
10 Gb/s Programmable Digital Delay Line
PDDL10
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
product
Fiber Optic Modem
VCH-608
The VCH-608 fiber optic modem is designed to receive and transmit via a fiber optic communication line (FOCL) signals of frequency and time standards (TSV) :- pulse signals 1 Hz (1 PPS) with delay compensation,- harmonic electrical signals with a nominal value frequency 100 MHz with phase instability compensation.
-
product
Low Cost Microwave Wideband APD Preamp Receivers
MR11 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR11 series microwave wideband optical receiver, adopts high Sensitivity APD diode and Low Noise Preamplifier IC, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
product
Solder Paste Analyser
SPA 1000
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
product
CCD Spectrometers
The Exemplar® Plus is a high performance smart spectrometer utilizing a low stray light unfolded Czerny-Turner spectrograph. It features a highly sensitive TE Cooled back-thinned (BT) CCD detector which is linearly summed for high dynamic range. Its long focal length, coupled with a high quantum efficiency detector, provides superior data quality over the entire 190-1100nm spectral range. The Exemplar Plus features a high signal to noise ratio, making it ideal for low light level applications, and also features a built-in shutter allowing for dark scan measurements, even while illuminated. As a member of the Exemplar product line, it features on board data processing and USB 3.0 communication. The Exemplar product line is also optimized for multi-channel operation featuring ultra-low trigger delay and gate jitter.
-
product
6 GHz Programmable Delay Line
PADL6
The PADL6 is a programmable delay line instrument designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 6 GHz. Delays are controlled via a TTL level bus.
-
product
Microwave Wideband Direct Modulated DFB Transmitters
MT52 (40KHz~20GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MT52 series microwave wideband direct modulated DFB transmitter, are able to transmit 20G microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc.
-
product
Recorders
* Field calibration of probes* Automatic probe recognition* Field replaceable probes* Battery backup* Independent channel alarms* 60 assorted charts included* LCD display (2 line)* Alarm delay: NO DELAY, 10 mins., 30 mins., 1 hr. or 2 hrs.* Real time data view.
-
product
10G DPSK Demodulator
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5,10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systemsutilized in commercial, defense and space exploration markets. The device plays a key role in improvingsignal quality and performance to meet the expanding demand for higher data rates and more complextransmission formats within current and next generation systems without major capital expenditure.Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. The measured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarization-dependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
product
3 GHz, 4 Channel Programmable Delay Line
QPADL3
The QPADL3 is a programmable delay line instrument with 4 independent channels designed for adjusting the time delay or phase of radio, microwave or even digital signals with bandwidths from DC to 3 GHz.
-
product
25-Seven Systems
The resulting product—Audio Time Manager—became radio’s preeminent solution for real-time compression and time-shifting, and has been used at some of the biggest talk stations in the world. Always on the bleeding edge, 25-Seven then reinvented the profanity delay with Program Delay Manager, adding the unprecedented capability to capture objectionable live content for future review. Now, 25-Seven Systems specializes in audio technologies and products that address unique problems in the industry. Most recently, 25-Seven has produced one of the most disruptive technologies in broadcast history—the Voltair line of water-marking enhancement products, which became one of the hottest and most game-changing products in the industry
-
product
ECHO 8 Ultrasonic Corrosion and Precision Thickness Gage
ECHO 8
Danatronics offers our newest ultrasonic precision thickness gage line, the ECHO 8 series. ECHO 8 represents our most advanced thickness gage ever combining dual and single element transducers all in one small package. ECHO 8 offers a 3.5” high resolution sunlight readable color display with live A-Scan, use of a wide variety of dual, contact, delay line and immersion transducers from 1-20 Mhz as default and custom created and stored applications setups, B-Scan, datalogger with up to 32GB of SD card memory and interface to Microsoft excel. The ECHO 8 is available in 4 models including the ECHO 8, ECHO 8DL, ECHO 8W and ECHO 8DLW. The vibrate on alarm feature is the world’s first and is great for loud environments
-
product
Optical Delay
ODL
The Peregrine Optical Delay Line (ODL) provides an exceptional combination of precision, speed, and optical stability at a low price. It is ideally suited for pump-probe experiments and autocorrelation measurements (both interferometric and intensity methods). Advanced voice coil technology allows the ODL to be positioned anywhere in its travel range to within 150 nm. That’s 1 fs for a double-pass configuration. The response time is as short as 1 ms. Our 1-cm-travel ODL is interferometrically stable (measured using a 650 nm laser). No backlash, no hysteresis and no drive trains to wear out as with stepper motors. It’s convenient–the ODL can be positioned using digital commands, an analog voltage or a combination of the two. Two 16-bit on-board analog-to-digital converters simplify data collection. Digital inputs and outputs allow master or slave clocking. An executable Windows application is provided to get you up and running in minutes. In addition, DLLs and LabVIEW Vis for integration into your software are also included.
-
product
Microwave Wideband PIN-TIA Receivers
MR22 (40KHz~18GHz)
Hangzhou Huatai Optic Tech. Co., Ltd.
MR22 series microwave wideband optical receiver, adopts High linear PIN diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 18Gb/s high speed communication system.
-
product
Programmable Delay Line Instruments
The XT Series
Our most precise programmable delay line instruments featuring Colby's patented trombone technology
-
product
Programmable Delay Line Instrument
The XR Series
A selection of common step sizes that gives you the broadest signal delay range among all our products
-
product
Model Vector Network Analyzer
DZV-1
Digital Signal Technology, Inc.
DZV-1 is the vector network analyzer which can be measured the impedance and VSWR of the antenna, S Parameter of RF component and devices. It is small and low-priced. So, it is suitable for the production line, laboratory use, various testing applications, and the educational use. The communication between the DZV-1 unit and PC is done via USB, which is also used for power supply. The LOG-MAG characteristic, the phase-characteristic, the group delay frequency characteristics, the Smith chart, the polar coordinates, the SWR characteristic can be displayed on PC.
-
product
Digital Controlled Phase Shifters To 4 GHz
Pulsar's Digital Controlled Phase shifters utilize PIN diodes and delay lines to produce the necessary phase requirements. These digital phase shifters use switched lines to obtain temperature stable phase shift. The phase is specified at the center frequency ± 3.0% and is proportional to frequency over the entire band.
-
product
X-Scan T
The X-Scan T series is a product family of TDI (Time Delay Integration) technology-based X-ray line cameras that are optimized for demanding industrial environments.
-
product
Quality Of Service
Traffic is prioritized according to its importance and some types of traffic are more sensitive to latency, jitter and packet loss than other. Xena offers QoS validation solutions in accordance with RFC 2544 and Y.1564, as well as advanced statistics functions that help users track, analyze and troubleshoot QoS to maintain a high service quality guarantee. Testing that link performance complies with a Service Level Agreement (SLA) includes verifying Frame Transfer Delay (FTD), Frame Delay Variation (FDV) and Frame Loss Ratio (FLR) at the Committed Information Rate (CIR) defined in the SLA. Verifying the SLA with the Xena1564 allows doing the test on a line simultaneously loaded with traffic from other services.
-
product
5 Gb/s Programmable Digital Delay Line
PDDL5
The PDDL5 is a precision time delay generator for digital signals. Delays are controlled precisely in 5, 10 or 20 ps increments from 0 to 5115, 10,230 or 20,460 ps range respectively. Data rates up to 5 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
product
Narrow Band Digital Signal Delay Lines
Advanced Science and Novel Technology, Co., Inc.
Narrowband (11GHz-17GHz) tunable clock phase shifterDelay adjustment range of 140psExhibits low jitter and limited temperature variation over industrial temperature range100MHz of bandwidth for the phase adjustment tuning portsIdeal for high speed proof-of-concept prototypingFully differential CML input interfacesFully differential CML output interface with 800mV single-ended swingLinearized data output for minimized undershoot/overshootSingle +3.3V or -3.3V power supplyPower consumption: 0.91WFabricated in SiGe for high performance, yield, and reliabilityStandard MLF/QFN 24-pin package
