Filter Results By:
Products
Applications
Manufacturers
Digital Input-Output
Input/output of digital values.
-
product
Digital Input/Output and Counter/Timer Card
PCI-DIO-96C3
This is a 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length 5V PCI-bus (or PCI-X bus) slot in X86 type PC’s.
-
-
product
Digital Input/Output Card
IOD-144
This is a 144-bit full-size card. A Programmable Peripheral Interface chip, type 8255-5 provides three 8-bit ports (A, B, and C) for each 24-bit group. Each port can be independently programmed for either input or output. Port C can also be configured as two 4-bit ports. These cards fully implement Mode 0 of the 8255 PPI chip. (Consult the factory if you desire to operate in Mode 1.) Type LS245 bi-directional transceivers sink 24 mA (optionally 64 mA) and source 15 mA. These transceiver buffers provide hysteresis correction on inputs and added drive capability on outputs. The direction of the transceivers is set by software.
-
product
Digital Input/Output Expander (Normally-Open Relay Contact Outputs)
ENVIROMUX-DI16DOR16
Adds 16 digital inputs and 16 digital normally-open relay contact outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for normally-open relay contact outputs. Accepts 26 to 16AWG wire. Potential free. Rated switching load: 0.5A @ 125 VAC, 1.0A @ ±30VDC. Fused. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Includes 5V/3A power supply. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.78 in (165x79x45 mm). Regulatory approvals: RoHS.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C/i(DIOi480)
The D480C/i offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
Digital Input/Output Cards
PCI-DIO Series 24 and 48
The PCI-DIO-48/48S, PCI-DIO-48JP/JPS, PCI-DIO-48JPL/JPLS, PCI-DIO-48H/HS and PCI-DIO-24S are 24- and 48-bit parallel digital input/output cards designed for use in PCI-Bus computers. The card is 6.9 inches (175 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
product
Digital Input / Output Data Acquisition (DAQ) Products
In many cases, we only need to know a simple status about the device we are trying to collect data from, whether something is true or false, on or off, in one position or another. In these cases, we can determine what we need to know using a digital input, or control these things by a digital output. Digital I/O can fit into many applications.
-
product
Digital Input/Output Expander (Open-Collector Outputs)
ENVIROMUX-DI16DO16
Adds 16 digital inputs and 16 digital open-collector outputs to the ENVIROMUX-2D/5D/16D. Interfaces with the ENVIROMUX-2D/5D/16D via the RJ45 Sensor Port. Digital inputs: 16 screw terminal pairs for connecting dry contact devices; One screw terminal pair for tachometer; 0 to 255 Hz. Accepts 26 to 16AWG wire. Potential free. Voltage range: 0 to +36VDC. Over-voltage surge protected. Digital outputs: 16 screw terminal pairs for open-collector outputs. Accepts 26 to 16AWG wire. Rated sink current: 500 mA per output. +5VDC, 22kΩ pull-ups. Voltage range: 0 to +24VDC. Over-voltage surge protected. Supports CAT5/5e/6 cable up to 500 ft. (152.4 m). Powered by ENVIROMUX-2D/5D/16D. Compatible with ENVIROMUX-2D/5D/16D. Dimensions WxDxH: 6.49x3.10x1.08 in (165x79x27 mm). Regulatory approvals: RoHS.
-
product
32-CH 80 MB/s High-Speed Digital I/O Card
PCIe-7300A
ADLINK PCIe-7300A is an ultra-high-speed digital I/O card. It consists of 32 digital input/output channels. High performance designs and state-of-the-art technology make this card ideal for a wide range of applications, such as high-speed data transfer, digital pattern generation and digital pattern capture applications, and logic analyzer applications. Trigger signals are available to start the data acquisition of pattern generation.
-
product
ADC 12-bit @ 2.6 GSPS and DAC 14-bit @ 5.6 GSPS, FMC
FMC216
The FMC216 is an FPGA Mezzanine Card (FMC) per VITA 57 specification. The FMC216 utilizes AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a DAC AD9129 providing 14-bit conversion rates of up to 5.6 GSPS. The analog input/output, digital output, clock and trigger interfaces of the FMC216 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
product
96-CH High-Driving DIO Card
PCIe-7396
The PCIe-7396 is a 96-bit parallel digital input/output (DIO) card esigned for industrial applications. The plug and play feature of PCI Express Bus architecture makes it easy for users to install the PCIe-7396 on their systems quickly.
-
product
48-Channel DIO Function Card
ProDAQ 3610
The ProDAQ 3610 high-speed DIO function card is a high-density card that fits into ProDAQ VXIbus motherboards and LXI function card carriers. This high-speed DIO card has 48 channels and is designed for demanding applications ranging from normal slow digital input/output to high-speed pattern generation and pattern recognition. The card provides the user with 384 input/output channels if eight DIO function cards are fitted to one ProDAQ motherboard.
-
product
USB Modular Isolated Digital Input/Output
U2600A Series
The Keysight U2600A Series U2600A Series USB Modular Isolated Digital Input/Output Devices are high performance modules that comprise of three models U2651A isolated 32-bit DI and 32-bit DO, U2652A isolated 64-bit DI and U2653A isolated 64-bit DO. The U2600A Series provides up to eight channels with 64-bit of high density opto-isolated digital input and digital output for USB 2.0 interface-based industrial applications like driving relays, actuator, or valve. The U2600A Series targets a wide range of application both in industrial automation and education.
-
product
Intelligent A/D I/O Unit
RAD242
Model RAD242 is an intelligent, two-differential-channel, 24-bit analog-input interface unit that includes a Delta-Sigma A/D converter. The converter has a digital output filter with adjustable notch frequency from 10 Hz to 2000 Hz. The pod also has 13 bits of digital input/output. A precision 10 VDC voltage that can be used for transducer excitation is available at connector pin 5. As much as 60 mA current can be provided. It is packaged in a NEMA 4 enclosure for remote installation in harsh environments. RAD242 also provides a user-definable interrupt input and counter/timer input. An optional RAD Firmware Development Kit is available if you wish to use those user-programmable input lines or to develop a custom program.
-
product
Modbus Digital Input Output Modules
DAT3100 Series
The Datexel DAT3100 series is a range of Modbus digital input output modules. These cards or modules have the ability to accept digital voltage inputs and provide an output by the way of relays, NPN or PNP transistors. The DAT3100 devices can communicate with RS485 or RS232 on a Modbus or ASCII protocol making the DAT3100 series a very economical solution to large and small scale Data Acquisition. Combining these digital input output devices with the DAT9000 controllers and the DAT3000 analog input output modules make Datexel the smart choice where Data Acquisition is needed.
-
product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
product
PMC Digital IO Board
MS 1815
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*128 channel digital I/O signal*Input/output ON state=3.5V to 5.0 max at -24mA*Input/output OFF state= 0.8max at 24mA*16 groups of 8 channels can be programmed as input/output*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
product
PMC w/ 16x/8x ADC, 8x/4x DAC & 14x Digital I/O
TPMC532
The TPMC532 provides 16 or 8 channels of simultaneous sampling true differential bipolar 16-bit analog input, 8 or 4 channels of simultaneous update single-ended unipolar/bipolar 16-bit analog output and 14 channels of tri-state 5V-tolerant TTL digital input/output.
-
product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C
The D480C offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
product
Low Profile Isolated Digital Input/Output Card
LPCI-IIRO-8
The LPCI-IIRO-8 is a half-size Low-Profile PCI bus compatible card that provides isolated digital input and output interface for PCI-Bus computers. The card has eight optically-isolated digital inputs for AC or DC control signals and eight electromechanical relay outputs. LPCI-IIRO-8 occupies four consecutive 8-bit registers in I/O space.
-
product
Digital I/O Card
PCI-DIO-120
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
-
product
256 Digital Input/Output Channels
CP387
The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concept allows multiple digital I/O types to be configured within a single module to match the application requirements.
-
product
256 Channel Digital Input / Interrupt Output Module
DP-VXI-3099
DP-VXI-3099 is a high density module that provides 256 channels of digital input/interrupt and/or output for large scale digital input monitoring and control.
-
product
48-CH DIO & Timer/Counter Cards
cPCI-7248/7249R
- PICMG 2.0 Rev 2.1- 48-CH digital TTL/DTL input/output- Emulates 4/2/1 industry standard 8255 PPI (mode 0)- Direct interface with OPTO-22 compatible I/O modules Output port status read back- On board 8254 timer/counter chip
-
product
Digital Port
ZET 7160
*Logical analyzer*Digital input/output, 4 bits, 0/5 V*CAN 2.0 Interface
-
product
96 Channel Isolated Digital Input / Interrupt Output Module
DP-cPCI-3096
96 Channel Isolated Digital Input / Interrupt Output Module
-
product
64 Channel Isolated Digital Input/Interrupt/Output Module
DP-VME-3636
DP-VME-3636 is a 64-Channel Isolated Digital Input/Interupt/Output Module. This module provides 32 channel digital input and 32 channel digital output with isolation. Channels are divided in 2 groups of 16 channels each and are routed to rear I/O. 16 non-isolated TTL channels are available.The module is used for digital interface, status setting, status monitoring, automatic test equipment, and high density industrial automation.
-
product
Digital Expansion Board
MSXB 013
Digital Expansion Boards. The MSXB 013 Digital Input/Output Expansion Board expands 16 digital input lines and 16 digital output lines to 64 digital input lines and 64 digital output lines.
-
product
Modbus RTU Analog Input Modules
The Datexel range of Modbus RTU analog input cards for both RS485 and RS232 with Modbus or ASCII protocol can be combined with the DAT9000 series of Modbus Masters. A choice of input cards or modules are available and have various optional inputs such as Voltage, Current, Thermocouples, RTD, and Resistance. Also a choice of 2, 4, 8 channel options are available. The DAT3011 is a Modbus RTU Slave with 1 selectable universal input (Thermocouples, RTD, mV, RTD's or Resistance), 2 x 4-20mA or 0-10V input and 2 x4-20mA outputs. The DAT3011 also has 3 digital inputs and 3 relay outputs. Each module is isolated from each other and is set up using the DAT3000 software Development package which is free of charge from the Datexel download web page. Datexel also has universal input modules. An 8 channel analog input card is available making the DAT3000 series a very economical solution to large and small scale Data Acquisition. Combining these analog input cards with the analog output cards, the digital input/output cards and the communication devices make Datexel the smart choice where Data Acquisition is required.
-
product
USB Digital Input/Output Module
USB-DIO-32
The USB-DIO-32 is an ideal solution for adding embedded, portable, easy-to-install digital I/O and counter capabilities to any computer with a USB port. The USB-DIO-32 is a USB 2.0 device, offering the highest speed available with the USB bus. It is fully compatible with both USB 1.1 and USB 2.0 ports. The board is plug-and-play allowing quick connect or disconnect whenever you need additional I/O on your USB port.
