Filter Results By:
Products
Applications
Manufacturers
- Taylor Dynamometer, Inc.
product
550 HP Water Brake Chassis Dynamometer
CM-51S
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
product
Chassis Dynamometer Smoke Testers
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
product
Display-Only Dynamometer Testing Instrument
DynTek-PC
The DynTek-PC for engine dynamometers is a display-only system intended for basic engine dynamometer testing requirements. This system provides for the measurement of torque in either tension or compression (both clockwise and counter-clockwise engine rotation) and speed from a standard Magnetic Pickup. The system is designed to set on a table or desktop near the PC.
-
product
Power Amplifier
5241
The Model 5241 is a voltage-controlled power amplifier designed exclusively for Magtrol's Model HD-825 Hysteresis Dynamometer. Because of its double braking system, the HD-825 requires more than 4 amps of power in order to reach full torque. The 5241 (which can provide up to 5 amps of output current) is necessary in order to amplify the power between a 6200 or DSP6001 Controller (which both have a maximum current output of 1 amp) and the HD-825 Dynamometer.
-
product
Portable Engine Dynamometers
Cost-effective Portable Engine Dynos from Taylor Dynamometer are water brake style systems for diesel applications up to 1,250 hp (932 kW) and 3,000 ft-lb (4,068 N) of torque. Mount yours right on the engine in minutes for fast, convenient and reliable testing.
-
product
AccuDyne™ AC Dynamometer Systems
SAKOR Technologies offers the AccuDyne™ series of AC motoring dynamometers. These 4-quadrant dynos offer full motoring as well as loading capabilities. AccuDyne dynamometers can be used for testing active components such as engines and electric motors as well as passive components such as transmissions, generators and alternators. AccuDyne dynamometers are available in models from 5 kW through 3 MW. SAKOR Technologies configures each AccuDyne system to meet customer-specific requirements.
-
product
Towing Dynamometer
RS-90K
RS-90K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-90K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-90K is designed to maintain 90,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Dynamometer
I-Series
AW I-Series dynamometers are excellent for diesel engine testing as well as other applications. The electronic load control system on this hydraulic activated dynamometer allows for precise and steady control of Power and RPM levels.
-
product
Engine Dynamometer
DX33
Power: 750 hp (559 kW)Torque: 2,413 lb-ft (3,271 Nm)Speed: 4,000 rpmWater Use*: 55 gpm (208.2 lpm)Inertia Value**: 62.4 lb·ft2 (2.6 kg·m2)Shipping Weight: 1,648 lb (748 kg)Rotation: bi-directional
-
product
Engine Dynamometer
DE200
Power: 268 hp (200 kW)Torque: 590 lb-ft (800 Nm)Speed: 8,000 rpmWater Use*: 37 gpm (140.1 lpm)Inertia Value: 8.28 lb·ft2 (0.349 kg·m2)Shipping Weight: 1,863 lb (845 kg)Rotation: bi-directional*No Cooling System
-
product
Engine Dynamometer
DE720
Power: 966 hp (720 kW)Torque: 3,320 lb-ft (4,500 Nm)Speed: 3,750 rpmWater Use*: 124 gpm (469.4 lpm)Inertia Value: 126 lb·ft2 (5.3 kg·m2)Shipping Weight: 9,259 lb (4,200 kg)Rotation: bi-directional*No Cooling System
-
product
Four-Wheel Drive Dingle Roller Dynanometer for Cars with Axle Load of up to 2.4T, for Installation in an Existing LPS 3000 Dynanometer
MSR 500/2 CAR 4WD (LPS 3000) | VP 230038
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD is suitable for installation in an existing LPS 3000 base.
-
product
Performance Dynamometer
The MD-250-HD was designed to be a performance dynamometer first, with the added benefit of being able to test 2-wheel-drive heavy-duty vehicles such as truck, buses and commercial vehicles. No other dyno in its class offers more value or better in-house motor vehicle testing capabilities than the Mustang MD-250-HD. For starters, the MD-250-HD can boasts a 1,500 horsepower measurement capacity at a top speed of 175 mph and a powerful air-cooled eddy current brake provides the MD-250-HD with 900-hp worth of loading capacity for steady state testing.
-
product
Towing Dynos for Compact to Mid-Sized Light-Duty Vehicles
Designed to maintain 1,214 to 1,798 lb (5,400 to 8,000 N) of constant drawbar pull, our towing dynamometers for compact to mid-sized light-duty vehicles feature aluminum frame, independent suspension, aerodynamic body and wireless touchscreen controller.
-
product
Water Brake Dynamometers
TD Series
With a versatile variety of six models, TD Series Water Brake Dynos offer are well-suited for both steady state and modest transient testing in a wide range of medium- to heavy-duty applications.
-
product
Engine Dynamometer
H3606
Power: 2,000 hp (1,491 kW)Torque: 23,873 lb-ft (32,367 Nm)Speed: 2,550 rpmWater Use*: 146 gpm (552.7 lpm)Inertia Value**: 311.4 lb·ft2 (13.12 kg·m2)Shipping Weight: 3,339 lb (1,515 kg)*No Cooling System**With Companion Flange
-
product
Engine Dynamometer
DX36
Power: 1,500 hp (1,119 kW)Torque: 4,825 lb-ft (6,542 Nm)Speed: 4,000 rpmWater Use*: 109 gpm (412.6 lpm)Inertia Value**: 121.6 lb·ft2 (5.1 kg·m2)Shipping Weight: 2,240 lb (1,016 kg)Rotation: bi-directional
-
product
Eddy Current Dynamometer
EC Series
Specifically designed for small displacement diesel engines, the Eddy Current (EC-Series) engine dynamometer features in-line eddy current absorption units in a robust, compact frame. The air-cooled eddy current absorbers eliminate the need for an expensive water recirculation system and most engines being tested can be cooled with a standard closed-circuit radiator system. This compact air-cooled design results in a minimal environmental impact and the ability to be easily relocated with no need for a permanent installation. When combined with PowerNet LT, our fully automated dynamometer control system, all of your testing needs can be performed at the touch of a button.
-
product
Dynamometer
Water Brake Series
The Water Brake (WB) Series Dynamometers are designed with aggressive rotor fin technology that allows for higher torque without the need for multiple rotors. The 0-4000 RPM range and high torque capacity make this dynamometer series an excellent choice for testing a wide range of motors from low RPM DC motors to 2 pole AC motors.
-
product
Hybrid & Electric Vehicle Dynamometer Testing
SAKOR Technologies Hybrid/Electric Vehicle Powertrain Dynamometer Test System (HEViDyne), winner of the SAE 2008 Technical Award for Hybrid/Electric Vehicle Testing Technology, is a comprehensive solution for performance, efficiency, and durability testing of all types of hybrid and electric vehicle drivetrains, including:*Hybrid assist (parallel hybrid)*Gasoline or diesel/electric (serial hybrid)*Fully electric vehicles
-
product
Emissions Dynamometers
MD-100-M-2WD
High throughput demands of Centralized Emission Inspection require the use of rugged and durable emission inspection equipment. Designed from inception to withstand punishing use and misuse, Mustang Dynamometer has set the performance standards of equipment manufactured and used worldwide for centralized emissions testing. Our pioneering experience has led us to be the world leader in the design and manufacturing of rugged inspection and maintenance hardware and software for the I/M industry. We have centralized testing lanes installed all over the world in climates from cold to hot and from wet to dry. By the end of 2020 we estimate that our equipment will have performed nearly 1.5 billion vehicle tests. Continuous improvement leads us to innovative solutions based on our knowledge of design, service, maintenance, ergonomics and overall functional capabilities. Mustang I/M Centralized Emission Inspection equipment is designed for our customer’s demands.
-
product
Engine Dynamometer
DE400
Power: 536 hp (400 kW)Torque: 1,475 lb-ft (2,000 Nm)Speed: 8,000 rpmWater Use*: 74 gpm (280.1 lpm)Inertia Value: 26 lb·ft2 (1.107 kg·m2)Shipping Weight: 4,012 lb (1,820 kg)Rotation: bi-directional*No Cooling System
-
product
DynEDGE Controller
The DynEDGE controller offers an integrated, multi-loop control and data acquisition system in an off-the-shelf solution for dynamometer applications, including system modernizations, new installations, turnkey systems, and complete test cell control and data acquisition systems. The controller provides both speed and torque control with four control channels that can be configured for ±100 mA, ±10 V, and ±20 mA.
-
product
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KG
FM-204M50KG
Guangzhou Landtek Instruments Co. Ltd.
LANDTEK Digital Muscle Dynamometer Muscle Strength Tester FM-204M50KGApplications:Making job task analysis and ergonomic analysis simple and accurate, it is ideal for workplace design, strength assessment and ergonomic research.Details:Force Rang:±50kgf,±490N,±110LbfResolution:0.01kgf,0.1N,0.1LbfAccuracy:±0.5%FS ± 1DigitUnit:kgf, gf, N, LbfMeasurement State:Peak Value Measurement, Real Time MeasurementDisplay:2 Reversed 4 Digit LCDPower Off:10 Minutes Auto Power Off, Manual Power OffBacklight:BacklightSafe Load:150%FS (Buzzer Alarm Over 110%FS)Power Supply:2x1.5 AA(UM-3) Battery or 5VDC Power SupplyOperating:0°C~40°CConditions:< 80%Surrounding:No Vibration Source or Corrosive Medium AroundWeight:705 gSize:host machine:170mm*72mm*35mmhandspike:315mm*Φ30mm Instrument stents：155mm*95mm*35mmAccessories:Standard Accessories:ManualCarrying CaseInstrument stents4 M3*18 screwsE-1005Optional Accessories:External USB power supply cableE-1004For quotation please feel free to contact Lisa Li. Thank you.
-
product
Engine Dynamometer
DX33-HS
Power: 750 hp (559 kW)Torque: 2,413 lb-ft (3,271 Nm)Speed: 6,000 rpmWater Use*: 55 gpm (208.2 lpm)Inertia Value**: 62.4 lb·ft2 (2.6 kg·m2)Shipping Weight: 1,648 lb (748 kg)Rotation: bi-directional
-
product
Towing Dynamometer
RSL-15K
RSL-15K Towing Dynamometer is designed for testing today’s full-sized cars, to mid and full-sized SUVs. The unique design of the RSL-15K allows it to be used for a wide range of vehicle weights. Built with an all-aluminum frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-15K uses two eddy current absorbers for power absorption. The power is provided by batteries and an alternator.
-
product
AWD Dynamometers
MD-AWD-800
Mustang designed the MD-AWD-800-DE-24×2 Series to be a dyno that could be easily adapted to fit virtually any testing scenario without ever having to compromise. In AWD mode, the 800 Series XL can test AWD vehicles with wheelbases up to 134” long, enough to handle Hummer H1s. In 2WD mode, the 800 Series uses a single 24” diameter roller with a low base mechanical inertia to allow you to test the lightest vehicles out there.
-
product
Towing Dynamometer
RS-125K
RS-125K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-125K is built with a heavy-duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-125K is designed to maintain 125,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds
-
product
Powertrain
The MOTOMEA Electric Powertrain Dynamometer is part of a fully integrated modular system with hardware-in-the-loop testing. System capabilities include drive cycle and virtual test driving. Powertrain testing capabilities also include battery testing and simulation using bidirectional DC power supply.
-
product
1100 HP Water Brake Chassis Dynamometer
TD-36
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 13,200 lb (5,987 kg)Capacity: 1,100 hp at 45 mph (820 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in. (1219 to 1880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
-
product
1650 HP Water Brake Chassis Dynamometer
TD-36X3
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 22,000 lb (9,979 kg)Capacity: 1,650 hp at 45 mph (1,230 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 6 fixed rolls to accommodate axle spreads from 48 to 74 in. (1,219 to 1,880 mm) tandem centers and 50 to 64 in. (1,270 to 1,626 mm) tridem centersPit Required Depth: 35 in. (889 mm)
