Filter Results By:
Products
Applications
Manufacturers
EMI Receivers
measure conducted and radiated emissions for compliance to EMC standards.
See Also: EMI, RFI, Near Field Probes
- Virginia Panel Corporation
product
Cable Assembly, Receiver, TriPaddle/Coax, 20", 68-PIN Male VHDCI, 4 SMA Plugs, 2 SMB Plugs
540170010143
Cable Assembly, Receiver, TriPaddle/Coax, 20", 68-PIN Male VHDCI, 4 SMA Plugs, 2 SMB Plugs.
-
product
Phase Noise Measurement Application
N9068A
One-button measurements for analyzing phase noise in frequency domain (log plot) and time domain (spot frequency)Compatible with phase noise measurement personality in Keysight PSA and ESA spectrum analyzers Runs inside the PXA, MXA, EXA signal analyzers and MXE EMI receiver
-
product
Radiated Emission
High accuracy CISPR 16-1-1 EMI receivers and high precision calibrated antennas for radiated emission measurements.
-
product
Attenuators And Pulse Limiters
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
product
Talon 26 GHz Sentinel Intelligent Signal Scanning RTX Extreme Recorder
Talon RTX 2684
- Search and capture system using Pentek's Sentinel™ Intelligent Signal Scanner- Captures RF signals from 1 GHz to 26 GHz- Capture and scan bandwidths up to 500 MHz- Selectable threshold triggered or manual record modes- 12-bit A/Ds with 57.5 dB SNR & 72 dB SFDR- Built-in DDC with selectable decimations of 4, 8 and 16- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight: about 23 lb (10.4 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow® GUI, SystemFlow API, and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
product
ITA, 9025, 25 Module, EMI, with 8" Enclosure
410104304
This 9025 ITA comes with an 8" enclosure for ease of system integration. The ITA is designed to work with the 9025 EMI receiver.
-
product
EMI Receiver
KH3939
Beijing KeHuan Century EMC Technology Co,.LTD
KH3939 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3939 receiver is from 9kHz to 300MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be carried out. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing. The KH3939 receiver uses a USB interface for data transmission, and supports USBinterface peripheral devices such as printers, mice, keyboards, etc. The machine is equipped with a high-speed and large-capacity hard disk, which stores a variety of external device data, and supports plug and play. External test equipment. The software is self-developed by our company, using windows as the carrier, users who are familiar with the operation of windows can quickly get started. The machine can independently carry out test work without additional control equipment for control operations, which fundamentally solves the problem of interference sources. The measurement results can be input to the hard disk in the receiver or stored in a floppy disk through a floppy drive or printed out directly or savedusing a USB storage device. The detailed measurement report can be printed directly according to user needs without additional editing.
-
product
Absorbing Clamp
AB-CLP
• EMI Receiver equipped with absorbing clamp can indirectly test radiated interference power of household electrical appliance, power tool and similar electrical appliance with frequency from 30~300MHz.
-
product
EMI and EMC Test System
EMI receiver system. It is a main test system for EMI (Electro Magnetic Interference) testing. The EMI-9KB is produced by the full closure structure and strong electro-conductibility material, which has high shielding effect. Due to the new technology for the EMI Test System, it solved the instrument self-EMI problem.
-
product
8-Channel 250 MS/sec RF/IF Extreme 1/2 ATR Recorder
Talon RTX 2590
- Rugged 1/2 ATR MIL-spec chassis- Designed to MIL-STD-810 for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Designed to MIL-STD-461 for radiated and conducted RF- EMI power line filter- Compact and lightweight design - 22 lb (10kg)- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- RF/IF recording with eight phase coherent 250 MHz 16-bit A/Ds- Sustained real-time record rates up to 4 GB/s- QuickPac drive packs add a valuable convenience to the 1/2 ATR recorder with up to 61 TB data storage- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
product
Receiver, G20, 20 Module, 6.75" Series Adapters, EMI
310120193
Receiver, G20, 20 Module, 6.75" Series Adapters, EMI
-
product
EMC Test Equipment
TDEMI G series
TDEMI stands for a novel generation of EMI measurement systems providing real-time analysis and enabling the user to perform high-quality emission measurements in a fractional amount of time compared to conventional EMI receiver technology. Ultra-fast Analog-to-Digital Conversion as well as real-time signal processing allows to emulate the behavior of instruments like oscilloscopes, receivers and spectrum analyzers. Due to the TDEMI's powerful signal processing hardware platform, corresponding to a computation power of approx. 80 conventional. PCs, such measurements are extremely fast in comparison to state of the art solutions.
-
product
EMC- EMI test Equipments
Our AFJ FFT 3100 & 3300 EMI Receivers cover the full frequency range from 9kHz to 3GHz.To allow a greater flexibility GTemCell can provide either a single or multiple solution of receivers to cover the most common standards and regulations such as CISPR, EN, IEC, FCC etc.
-
product
Protective Cover, G20x, Receiver, EMI
310113693
G20x offers the features of the G20 system, and adds an additional 8 modules in an extended tier for higher I/O needs. This solution uses 6.75" Series Pull-Thru Adapters.
-
product
200 MS/sec RF/IF Extreme 1/2 ATR Recorder
Talon RTX 2586
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- RF/IF recording with phase coherent 200 MHz 16-bit A/Ds and DDCs- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow GUI, API and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
product
EMI Test Receiver
ESL
The R&S®ESL EMI test receiver combines two instruments in one, measuring EMC disturbances in accordance with the relevant standards and also serving as a full-featured spectrum analyzer for diverse lab applications. The combination of very good RF characteristics and all of the important functions needed for fast, precise measurement and evaluation of the EMC of a device under test in accordance with commercial standards is unmatched in this instrument class.
-
product
PXE EMI Test Receiver, 1 Hz to 44 GHz
N9048B
Keysight's N9048B PXE is a standards-compliant EMI test receiver equipped with an RF pre-selector and LNA designs. Shorten your overall test time and easily perform gapless signal capture and analysis with real-time scan (RTS) capabilities.
-
product
EMI Receiver
KH3931
Beijing KeHuan Century EMC Technology Co,.LTD
* Detection frequency range: 9KHz-30MHz * Frequency stability: 1X10-6 * Frequency resolution: (9kHz ~ 150kHz): 30Hz; (150kHz ~ 30MHz): 1kHz * Test error: ±2dB * Corresponding characteristics of pulse: in line with national standard GB/T6113.1-1995 * Detection time constant: in line with national standard GB/T6113.1-1995
-
product
EMI64k Automation Software Suite
The EMI receiver families TDEMI® of GAUSS INSTRUMENTS® provide a huge fully CISPR compliant real-time bandwidth and therefore allow to speed up your measurements tremendously and to reduce the measurement uncertainty significantly - both at the same time. By using the full automation software suite EMI64k from GAUSS INSTRUMENTS the test procedures according to the CISPR 16-2-3 standard for the FFT-based measuring instruments as well as conventional testing (pre-scan and final maximization) and further EMC Standards are available. In comparison to the previously conventional pre-scan and final measurement strategy, the overall test quality can be significantly increased whereas the testing times are reduced by orders of magnitudes.
-
product
3.6 GS/sec Ultra Wideband RF/IF Extreme 1/2 ATR Recorder
Talon RTX 2589
- Rugged 1/2 ATR MIL-spec chassis- Designed for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 22 lb (10kg)- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Capable of recording RF/IF frequencies to 2.8 GHz- Ultra Wideband recording with 3.6 GHz 12-bit A/D- Selectable 1.8 GHz dual channel mode- Up to 61 TB of solid state storage in removable QuickPac- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
product
EMI Test Receiver
KH3938B
Beijing KeHuan Century EMC Technology Co,.LTD
Is a fully automatic radio disturbance test receiver and is the main tool for EMI testing. KH3938B receivers frequency range 9kHz-1GHz, in accordance with: 2010 and GB / T6113.101-2016 development standards designed to meet the requirements of the standard-compatible, can be used to power emission test, Sao conduction disturbance voltage test, radiated disturbance within 1G test. The receiver has the advantages of fast test speed , strong maneuverability, stable performance, and convenient test data processing.
-
product
EMI Receiver
KH3935
Beijing KeHuan Century EMC Technology Co,.LTD
KH3935 type EMI test receiver interference test receiver is fully automatic, is EMI major tool for testing. The frequency range of the KH3935 receiver is from 9kHz to 30MHz , which satisfies the power line disturbance power test. After configuring the artificial power network, the power terminal disturbance voltage test can be performed. The machine has fast test speed, strong maneuverability, stable performance, Advantages such as convenient test data processing.
-
product
Antenna Impedance Converter
The low noise impedance matching equipment has a high impedance input with minimized capacity. With the 50 Ω output it can be used with common EMI receivers or spectrum analyzers to measure the emissions received by an antenna on a vehicle.
-
product
EMI Test Receivers
EMI test receivers; extremely accurate instruments designed to detect electromagnetic emissions rigorously, to ensure all emissions conform to the Standard being tested to. Configured to set up running the required tests for parameters defined by the Standards as simply as possible, including automated test routines. R&S EMI test receivers can be much more too, with a full signal and spectrum analyzer in the same instrument.
-
product
RS-232 and RS-562 Transceivers
Analog Devices offers single, dual, and combination transceivers of up to five RS-232/RS-562 drivers and receivers for 1.8 V to 5.5 V power supplies. Data terminal equipment (DTE) or data communications equipment (DCE) configurations are also available in 3.3 V or 5 V versions. Galvanically isolated modules break ground loops and provide a convenient, self-powered, isolated, low EMI solution that drastically reduces component count and design complexity.
-
product
EMI Test Receiver
ESR
The R&S®ESR is an EMI test receiver build to measure electromagnetic disturbances using conventional stepped scans or ultrafast FFT based time domain scans. It also functions as a powerful signal and spectrum analyzer. The receiver features real-time spectrum analysis with a wide range of diagnostic tools for detailed analysis of disturbance signals and their history.
-
product
MXE EMI Test Receiver, 3 Hz to 44 GHz
N9038B
The Keysight N9038B is a standards-compliant MXE EMI test receiver and diagnostic signal analyzer built on an upgradeable platform. You choose the frequency coverage you need to fully test devices with outstanding accuracy and sensitivity across required ranges.
-
product
Receiver, ICon EMI , With Protective Cover And Strain Relief
310123102
Includes all of the standard features of the iCon, in addition to Electro-Magnetic Interference (EMI) protection. An earth ground terminal is included on the and a "mate first, break last" feature connects the earth ground circuit. The earth ground terminal on the strain relief prevents user shock and injury.
-
product
Serial FPDP Extreme 1/2 ATR Recorder
Talon RTX 2596
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed, conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Four-channel Serial FPDP record/playback- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- Single-mode and multi-mode fiber interfaces available- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
product
EMC Emission Measurements
AFJ manufactures a complete range of RF emission test equipment for EMC applications.Our FFT EMI Receivers cover the frequency range from 9kHz to 3GHz.
-
product
Receiver, 9025, 25 Module, EMI Gasket
310104431
The 25 Module Receiver is a rugged system devised to accommodate medium I/O. With high contact point availability, the 25 Module Receiver is suited for larger test and measurement systems. This 9025 offers a gasket for EMI applications.
